User manual

… the control element assigned to the input 6 in the
submenu "CH set" is switched to the Quick Link trim
function described below in this section. However, a
proportionate influence of the values set in the sub-
menu "D/R,EXP" of the function menu is retained.
In the displays described below, you specify the ef-
fect of the control elements assigned to channel
6 in the menu "CH set", page 92, in the form of
a Quick Link trim on the positions of the ailerons,
flaps,and possibly the elevators.
• CTL option (control/switch)
In the value field in the CTL column, assign a control
or control switch for a specific Quick Link to the mixer
as described in the section "Control, switch and con-
trol switch assignment" on page 38, for example in
the Quick Link "THERMAL":
BACK
NORMAL
Graubele
S
INC
RES
DEC
000%
000%
000%
000%
AILE1 AILE2
ON
ACT CTL
NEXT
SW3
RATE A
RATE B
NOTE:
If you select OFF , you switch off both the
Quick Link trim described here as well as
the values saved in the submenu
"D/R,EXP"! By default, this is 100% per side.
Lines RATE A / B
A symmetrical or an asymmetrical effect can be defined
for each flap pair. If you leave the travel setting in line
CH5 at 100% in the display "CH5-9" or "CH5-12" in
the menu "D/R,EXP", page 136, 5-20% is generally
sufficient.
Switch to the desired Quick Link, and touch the value
field to be set with a finger or the provided stylus:
BACK
NORMAL
Graubele
S
INC
RES
DEC
000%
000%
000%
000%
AILE1 AILE2
ON
ACT CTL
NEXT
SW3
RATE A
RATE B
Touch
The color of the value field switches from red to blue:
BACK
THERMAL
Graubele
S
INC
RES
DEC
000%
000%
000%
000%
AILE1 AILE2
ON
ACT CTL
NEXT
SW3
RATE A
RATE B
In the active (blue) value field, press INC to increase
the current value within a range of ±100% and DEC to
reduce it, for example:
BACK
THERMAL
Graubele
S
INC
RES
DEC
000%
+010%
000%
000%
AILE1 AILE2
ON
ACT CTL
NEXT
SW3
RATE A
RATE B
Use same procedure with the other values to be set, as
well as any inboard aileron "AILE3" and "AILE4".
Touch the RES button to reset a changed value in the
blue (and hence active) field to the default.
After completing the settings for the ailerons, you
can switch to the page for setting the flaps by touch-
ing NEXT at the right edge of the display and enter the
desired settings using the procedure described above,
for example:
Graubele
RES
–
+020%
+020%
+020%
+020%
FLAP1 FLAP2
FLAP3
FLAP4
+025%
+025%
+025%
+025%
RATE A
RATE B
BACK
THERMAL
S
INC
ON
ACT
CTL
NEXT
SW3
DEC
Finally, you can switch to the page for setting the
elevator by touching NEXT at the right edge of
the display and enter the desired settings using the
procedure described above, for example:
Graubele
RES
+005%
+005%
ELEV
SW3
RATE A
RATE B
BACK
THERMAL
S
INC
ON
ACT
CTL
NEXT
DEC
Note:
By default, no control has been assigned to
input 6 in the menu "CH set". However, you
can assign a control or switch at a time at any
time and hence set different flap positions within a quick
link as described in this section.
157
Airplane model function menu - Flap Sett
S1006_mz-24.3.en.indd 157 17.12.2014 15:22:25