User manual

flap servos.
Since all values are set separately, the aileron
deflections of the flaps can also be different.
Adapt the individual values as described above, for
example:
THERMAL
Graubele
RES
+055%
+055%
+055%
+055%
ON
AILE >> FLAP
+033%
+033%
+033%
+033%
CTL
RATE A
RATE B
FLAP2
FLAP3
FLAP4
BACK
S
INC
DEC
FLAP1
Note:
The available setting options depend on the
number of flaps selected in the "Model Sel" or
"Model Type" menu.
After you have finished making your settings, touch
the BACK button at the top left to return to the mixer
selection:
SET
CTL
ON
ON
BACK
NORMAL
Graubele
S
FLAP-TYPE ACT
ON
FLAP
AILE >> FLAP
ELEV >> FLAP
FLAP >> ELEV
INH
INH
INH
>>
>>
>>
>>
ELEV >> FLAP line
To support the elevator in tight curves and aerobatics,
the flap function can be included by controlling the
elevator with this mixer. Select the mixing direction so
that the flaps move downward when the elevator is
pulled (up), and conversely upward when the elevator is
pushed (down), that is, in an opposite direction.
A symmetrical or an asymmetrical effect can be defined
for each flap pair. Values of ±125% are possible. By
default, uniform values of +30% are set for the aileron …
SPEED
Graubele
RES
+030%
+030%
+030%
+030%
ON
ELEV >> FLAP
+030%
+030%
+030%
+030%
CTL
RATE A
RATE B
AILE2
AILE3
AILE4
BACK
S
INC
DEC
AILE1
… and the flaps:
SPEED
Graubele
RES
+030%
+030%
+030%
+030%
ON
ELEV >> FLAP
+030%
+030%
+030%
+030%
CTL
RATE A
RATE B
FLAP2
FLAP3
FLAP4
BACK
S
INC
DEC
FLAP1
Adapt the individual values as described under "FLAP
line".
Note:
The available setting options depend on the
number of flaps selected in the "Model Sel" or
"Model Type" menu.
After you have finished making your settings, touch
the BACK button at the top left to return to the mixer
selection:
SET
CTL
ON
ON
BACK
SPEED
Graubele
S
FLAP-TYPE ACT
ON
FLAP
AILE >> FLAP
ELEV >> FLAP
FLAP >> ELEV
INH
INH
INH
>>
>>
>>
>>
FLAP >> ELEV line
When setting flaps, upward or downward torque can
arise about the transverse axis. It may also be desirable
for the model to pick up the pace somewhat when
slightly elevating the flaps. Both of these reactions can
be achieved with the mixer.
When setting the flaps, you can use this mixer to
have the position of the aileron automatically track the
flaps depending on the set value. The setting can be
symmetrical or asymmetrical to the neutral point of the
flap control.
The adjustment range is ±125%. With this mixer, normal
settings lie within the single-digit to low double -digit
range. By default, 0% is uniformly set:
SPEED
Graubele
RES
000%
000%
ELEV
NEXT
RATE A
RATE B
ON
ELEV >> FLAP
CTL
BACK
S
INC
DEC
Adapt the individual values as described at the
beginning of this section under "FLAP line".
After you have finished making your settings, touch
the BACK button at the top left to return to the mixer
selection:
154
Airplane model function menu - Flap MIX
S1006_mz-24.3.en.indd 154 17.12.2014 15:22:24