User manual

Snap roll
Automated programming
Note:
This menu is hidden depending on the basic
settings of the "Model Sel" or "Model type"
menu.
In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the blue function menu. Use a
fi nger or the provided stylus to touch the "Snap roll"
menu item:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Idle LOW
Prog.MIX
Aile diff
Snap roll
Flap sett
Airbrake
Trainer
Telemetry
Touch
Some pilots like to automatically program snap rolls
when fl ying.
Flight-phase-dependent settings
If you have created Quick Links in the submenu
"Q.Link", page 132, and have assigned an appropri-
ate name, it appears at the top right in green font such
as "NORMAL". Activate the corresponding switches if
desired to switch between Quick Links:
RUDD
CTL
ON
INC
RES
DEC
ON
ON
INH
ELEV
BACK
NORMAL
Graubele
S
MODE AILE
ACT
ON
–100%
R/U
R/D
L/U
L/D
INH
INH
INH
–100%
–100%
–100%
+100%
+100%
+100%
–100%
+100%
+100%
+100%
–100%
The automated programming described here for the
mz-18 HoTT and mz-24 HoTT transmitters enables
up to four pre-programmed snap settings (positive right/
negative right and positive left/negative left) per Quick
Link. The position of the switch assigned to the indivi-
dual presets determines the respective fi gure program
in which the control stick signals are set at a fi xed value
independent of the momentary control stick positions.
That is, all aileron, elevator and rudder servos move
as if the relevant control stick had been shifted to the
preset position.
As usual, you can activate settings within a range of
±150% in the blue value fi eld activated by a fi nger or the
provided stylus with the three buttons at the right egde
of the display, for example:
RUDD
CTL
ON
INC
RES
DEC
ON
ON
INH
ELEV
BACK
NORMAL
Graubele
S
MODE AILE
ACT
ON
–100%
R/U
R/D
L/U
L/D
INH
INH
INH
–100%
–100%
–100%
+100%
+100%
+100%
–100%
+100%
+100%
+100%
–100%
In general, the individual fi gure programs are activated
and deactivated by switching the corresponding value
fi eld in the "ACT" column from INH to ON or vice
versa, by touching them with a fi nger or the provided
stylus, for example:
RUDD
CTL
ON
INC
RES
DEC
ON
ON
ON
ELEV
BACK
NORMAL
Graubele
S
MODE AILE
ACT
ON
–100%
R/U
R/D
L/U
L/D
ON
ON
ON
–100%
–100%
–100%
+100%
+100%
+100%
–100%
+100%
+100%
+100%
–100%
Finally, you should assign each activated fi gure pro-
gram, as described in the section "Control, switch and
control switch assignment" on page 38, a control with
which you can switch on and off the fi gure programs
during fl ight.
WARNING:
Never switch on one of these fi gure programs
accidentally, especially during fl ight! If the
programs are switched on at the wrong
location or time, it can cause signifi cant property
damage and/or injury.
After you have fi nished making your settings, touch
the BACK button at the top left of the display to return
to the menu selection:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Idle LOW
Prog.MIX
Aile diff
Snap roll
Flap sett
Airbrake
Trainer
Telemetry
149
Airplane model function menu - Snap roll
S1006_mz-24.3.en.indd 149 17.12.2014 15:22:20