User manual

THR.CRV
Setting the control characteristic of the Throttle/brake control stick
Note:
This menu is hidden when selecting a model
with "NO POWER" in the basic settings of the
"Model Sel" or "Model type" menu.
In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the blue function menu. Use a
fi nger or the provided stylus to touch the "THR.CRV"
menu item:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Flap MIX
Aile diff
Flap sett
Prog.MIX
V-Tail
Trainer
Telemetry
Butterfly
Touch
In this menu, you can adapt the carburettor
characteristic as well as the idle LOW and "motor off"
position of the throttle.
This menu allows you to change the control character-
istic of the throttle control stick independent of whether
the control function acts directly on a servo connected
to control channel 1, or via a number of mixers on
several servos.
Q.Link-dependent settings
If Quick Links are specifi ed in the "Q.Link" menu,
page 132, this option can be adopted depending on
the Quick Link. The name of the Quick Link is displayed
in green at the top right of the display, such as "NOR-
MAL".
First switch to the desired Quick Link, if desired.
Changing the control direction
In the wing program of the mz-18 HoTT and mz-24
HoTT transmitters, the rear throttle position is the
default for the "motor off" position with electric drives,
and "idle LOW" for gas motors. By inverting the throttle
curve, the control direction of the throttle can be
changed as needed from "accelerate from back to front"
to "accelerate from front to back".
Switch on the graphic and numerical display of the
control stick position by touching the ST OFF button
at the bottom left of the display with a fi nger or the
provided stylus, and then activate the Y-coordinate
adjustment option by touching the Y-axis button:
BACK
NORMAL
IN
OUT
POINT
OFF
INC
ENT
DEC
Y-axis
X-axis
ST ON
CURVE
–100%
–100%
000%
L
Graubele
S
Use the throttle to move a vertical green line between
the two endpoints "L" and "H" in the graphic. The mo-
mentary control stick position is also displayed numeri-
cally in the line "IN" (-100 % to +100 %).
Then move the throttle to one of the two end positions
such as the front. The green line moves the right and
disappears under the white frame. At the same time, the
color of the point at the top right changes from green to
red:
NORMAL
ENT
+100%
+100%
+100%
H
Graubele
BACK
IN
OUT
POINT
OFF
INC
DEC
Y-axis
X-axis
ST ON
CURVE
S
Hold down the DEC button at the right edge of the
display with a fi nger or the provided stylus to move the
red point down to a value of 000% in the line "POINT":
NORMAL
ENT
+100%
–100%
000%
H
Graubele
BACK
IN
OUT
POINT
OFF
INC
DEC
Y-axis
X-axis
ST ON
CURVE
S
Then move the throttle to the opposite end position,
such as the rear. The green line moves to the left, and
the points at the ends of the yellow horizontal line
change color:
NORMAL
ENT
–100%
–100%
000%
L
Graubele
BACK
IN
OUT
POINT
OFF
INC
DEC
Y-axis
X-axis
ST ON
CURVE
S
Use a fi nger or the provided stylus to hold down
the INC button at the right side of the display until a
value of +100% is reached in the "POINT" line.
144
Airplane model function menu - THR.CRV
S1006_mz-24.3.en.indd 144 17.12.2014 15:22:17