User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the blue function menu. Use a
fi nger or the provided stylus to touch the "Wing Mix"
menu item:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Flap MIX
Aile diff
Flap sett
Prog.MIX
V-Tail
Trainer
Telemetry
Butterfly
Touch
• Q.Link-dependent settings
If you have created Quick Links in the submenu
"Q.Link", page 132, and have assigned an ap-
propriate name, it appears at the top right in green
font such as "NORMAL". Activate the corresponding
switches if desired to switch between Quick Links.
• ACT column (active)
Within the value fi eld for this column, specify whether
the mixer is generally blocked INH or ON .
Once you set this value fi eld to ON , you can switch
on and off the mixer with a control assigned in the
right column "CTL".
Wing Mix
Adjusting mixers
• "SET" column
To switch to the setting menu, touch the correspond-
ing >> button in the "SET" column with a fi nger or
the provided stylus.
• Ctrl column (control/switch)
In the value fi eld in the Ctrl column, assign a control
or control switch to the mixer as described in section
"Control, switch and control switch assignment" on
page 38.
RUDD >> AILE line (rudder >> aileron)
Frequently, the behaviour of the longitudinal axis is infl u-
enced when the rudder is actuated. This is particularly
problematic in "knife edge fl ying" in which the only lift
is from the fuselage when the rudder is defl ected since
the wings are vertical in this fl ight position. This can
cause a model to rotate as if the aileron were actuated.
A correction is necessary along the longitudinal axis
(aileron) within an adjustable range when the rudders
are controlled.
Of course, the rudder and aileron remain separately
controllable.
The setting range of ±150 % makes it possible to appro-
priately adapt the direction of defl ection. This mixer can
optionally be switched on and off by one of the controls
which cannot be independently reset, or a control switch
if applicable, so that the model can be controlled exclu-
sively using the aileron or rudder.
To set the mixer, use a fi nger or the provided stylus to
touch the middle button in the line "RUDD >> AILE":
MIX.TYPE
RUDD >> AILE
AILE >> RUDD
RUDD >> ELEV
INH
INH
INH
>>
>>
ON
ON
ON
>>
ACT CTLSET
BACK
NORMAL
Graubele
S
Touch
The corresponding setting menu opens:
BACK
NORMAL
Graubele
S
RUDD >> AILE
A
(RATE) B
+100%
+100%
INC
RES
DEC
To enable this, touch the desired value fi eld, such as the
left one, with a fi nger or the provided stylus:
BACK
NORMAL
Graubele
S
RUDD >> AILE
A
(RATE) B
+100%
+100%
INC
RES
DEC
Touch
The color of the fi eld switches from red to blue:
BACK
NORMAL
Graubele
S
RUDD >> AILE
A
(RATE) B
+100%
+100%
INC
RES
DEC
Set the desired value with the INC or DEC button at
the right edge.
Use the same procedure for a value on the plus side of
the control travel, for example:
140
Airplane model function menu - Wing Mix
S1006_mz-24.3.en.indd 140 17.12.2014 15:22:14