User manual

Telemetry
The menus that fall under the generic term of "Tele-
metry" can be accessed from the blue function menu
of the mz-18 HoTT and mz-24 HoTT transmitters. Use
a fi nger or the provided stylus to touch the "Telemetry"
menu item:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Flap MIX
Aile diff
Flap sett
Prog.MIX
V-Tail
Trainer
Telemetry
Butterfly
Touch
In the basic transmitter display, you can open the
function menu by using a fi nger or the provided stylus to
touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
Basic operation
Basically the "Telemetry" menu corresponds to the
other menus of the mz-18 HoTT and mz-24 HoTT
transmitters:
BACK
Graubele
RX SELECT
SETTING & DATA VIEW
SENSOR
RF STATUS VIEW
VOICE TRIGGER
RX1
>>
>>
>>
>>
The few deviations are described below:
Switch between the individual pages of the "Telemetry"
menu by touching the ENT button (forward or "
")
and ESC (reverse or " ") with a fi nger at a provided
stylus. Corresponding pointers indicating direction can
be found on each page of the display at the top right in
the form of angled brackets ( ), such as:
BACK
Graubele
RECV
GENE
ELEC
VARIO
GPS
DEC
INC
ENT
SET
ESC
ESC
RX SERVO <>
REVERSE : OFF
CENTER : 1500µsec
TRIM : –000µsec
LIMIT– : 150%
>OUTPUT CH: 01
LIMIT+ : 150%
PERIOD : 20msec
If there is only one angled bracket, you are on the fi rst
or last page. You can then only change pages in the
displayed direction.
Menu lines in which parameters can be changed
are indicated by a preceding angle bracket (
) (see
screenshot above). Touch the INC or DEC button to
move the " " pointer one line up or down. Lines which
cannot be jumped cannot be changed.
To change a parameter, use a fi nger or the provided
stylus to touch the SET button at the right edge of
the screen. The corresponding parameter is red. Then
use the INC or DEC buttons to change the value
within the possible range, and accept the value by
touching SET . Touch the ESC button at the top right
of the display to return to the previous page, and touch
the BACK button at the top left of the display to return
to the initial position:
BACK
Graubele
RX SELECT
SETTING & DATA VIEW
SENSOR
RF STATUS VIEW
VOICE TRIGGER
RX1
>>
>>
>>
>>
Use a fi nger or the provided stylus to touch the button in
the desired submenu. If however the following message
appears instead of the desired submenu …
BACK
CLR
ON
TX VOLT
02
4.7V
AUTO LOAD
RX VOLT
00
3.7V
STRENGTH
00
000%
ESC CUR.
00
000.0A
ESC VOLT
00
00.0V
STRENGTH ALARM
ON
… there is no connection with a receiver. Switch on
your receiver, or bind the corresponding receiver as
described on page 74, or activate it as described
under "Important instructions" on the previous page.
115
Function menu - Telemetry
S1006_mz-24.3.en.indd 115 17.12.2014 15:22:02