User manual

be connected to a TEACH transmitter, the transmitter
immediately reacts with acoustical alarms to switches
connected during the switch assignment. At the same
time, a warning message flashes every second at the
top left in the transmitter's main display (see the figure
at the end of the section, "Wireless HoTT system").
Open the switch that has just been assigned.
First, in the value field under "TYPE", change the
default RF to DSC-T in the bottom line to the right in
order to switch the DSC connector to "signal input":
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
PUPIL
PUPIL
PUPIL
PUPIL
TEACH
TEACH
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
SW8
OFF
DSC-T
CTL
BIND
TYPE
The model to be controlled by the PUPIL must be
programmed with all its functions including trim and any
mixed functions in a model memory of the mz-18 HoTT
or mz-24 HoTT TEACH transmitter. The HoTT receiver
of the relevant model must also be bound to the TEACH
transmitter since it is responsible for controlling the
model even in PUPIL mode.
A mz-18 HoTT or mz-24 HoTT TEACH transmitter
can be connected to any suitable PUPIL transmitter,
including transmitters with a classic 35/40 MHz range.
For example, a mz-18 HoTT or mz-24 HoTT TEACH
transmitter can be connected to a mc-24 PUPIL
transmitter.
If the connection to the PUPIL is not made
with a two-pin DSC socket but rather a three-
pin Trainer jack by Graupner, for a correct
connection to a PUPIL transmitter, the modulation
type PPM(10, 16, 18 or 24) must be set in the PUPIL
transmitter independent of the type of modulation
used in the TEACH transmitter.
PUPIL transmitter settings
The model to be controlled by the PUPIL must be
programmed with all its functions including trim and any
mixed functions in a model memory of the mz-18 HoTT
or mz-24 HoTT TEACH transmitter. If applicable, the
HoTT receiver of the relevant model must also be bound
to the TEACH transmitter. In principle, a HoTT PUPIL
transmitter can be connected to a TEACH transmitter
with the classic 35/40 MHz range since the required
PPM signal by the TEACH transmitter is applied to the
DSC socket of a HoTT transmitter.
Almost any transmitter from the past and current
Graupner product line with at least four control functions
can be used as the PUPIL transmitter. The PUPIL
transmitter should however be equipped with the
current connection module for PUPIL transmitters. The
module should be connected to the transmitter board in
accordance with the provided installation instructions.
The specified cable is used to connect to the TEACH
transmitter (see the next two pages).
More information can be found in the main Graupner FS
catalogue and on the Internet at www.graupner.de.
The control functions of the PUPIL
transmitter must act directly on the control
channels, i.e., the receiver outputs, without
any intermediate mixers.
With transmitters of the series "mc", "mx" or "mz", it is
best to assign the model name "PUPIL" to a free model
memory activated with the required model type ("wing"
or "heli"), and adapt the control arrangement (mode 1 …
4) and "THR min or PITC min front/rear" to the PUPIL's
preferences. All other settings as well as mixing and
coupling functions are made in the TEACH transmitter
and are transmitted by the TEACH transmitter to the
receiver.
With transmitters of the "mz" series, also use a finger
or the provided stylus to touch the value field under
"TYPE" in the bottom line of the "Trainer" submenu at
the bottom right of display to switch it to DSC-S and
hence switch the rear DSC transmitter connector to
"signal output":
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
PUPIL
PUPIL
PUPIL
PUPIL
TEACH
TEACH
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
SW8
OFF
DSC-S
CTL
BIND
TYPE
With a mx-20 HoTT, mc-16 HoTT, mc-20 HoTT
or mc-3 2 HoTT PUPIL transmitter, adapt the
modulation types to the number of control channels to
be transferred in the line "DSC OUTPUT" of the "BASE"
menu. For example, the signal package with modulation
type "PPM10" only contains control channels 1 … 5,
and channels 6 and higher are not included. In order for
the PUPIL to use one or more of channels 5 and above,
select one of the modulation types that includes the
required channels. If in addition PUPIL mode is to be
used with an existing model memory instead of a newly
initialized one in one of the aforementioned transmitters,
make sure to enter "HoTT" in the "Module" line of the
"BASE" menu. Otherwise, the PPM signal at the DSC
socket may be inverted.
In the case of older transmitters of the "D" and "FM"
type, check the servo direction and control mode
and change them if necessary by switching the
corresponding cables. If necessary, switch off all the
mixers or set them to zero.
If you wish to assign other control functions to the
TEACH transmitter in addition to the functions of the
two control sticks (1 … 4), assign control elements to
the inputs in the "Channel set" menu of the PUPIL
transmitter that correspond to the released function
inputs 5 … 12 in the "Trainer" menu of the TEACH
transmitter.
108
Function menu - Trainer
S1006_mz-24.3.en.indd 108 17.12.2014 15:21:58