User manual

In the basic transmitter display, use a fi nger or the
provided stylus to touch the gear icon labelled "F":
000 000
000
000
mz
000%
000%
000
000
BATT TIME 00: 01: 23
Graubele
M 1
0:01:23
NORMAL
000:00.0
000:00.0
4.1V
RX TX
RX 00.0V
Touch
The display switches to the blue function menu. Use a
fi nger or the provided stylus to touch the "Trainer" menu
item:
BACK
SYSTEM
BASE
FUNCTION
Q.Link
Wing MIX
D/R,EXP
THR.CRV
Flap MIX
Aile diff
Flap sett
Prog.MIX
V-Tail
Trainer
Telemetry
Butterfly
Touch
The mz-18 HoTT and mz-24 HoTT transmitters
come standard with a DSC socket in the rear of the
transmitter. This can be used to connect fl ight simulators
(as described on page 24), but also to integrate the
transmitter into a cable-linked trainer system.
In order to make necessary settings, open the menu
item "Trainer" by touching it with a fi nger or the provided
stylus:
Trainer
Connection between two transmitters with a DSC cable
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
NULL
OFF
RF
CTL
BIND
TYPE
Note:
•
In contrast to the display of the 12-channel
mz-24 HoTT transmitter in this section,
only channels 1 … 9 are offered in the
display of the 9-channel mz-18 HoTT transmitter.
• The above fi gure shows the initial status of this
menu: The PUPIL control has not been released;
neither has a switch been assigned.
TEACH transmitter settings
You can transfer up to nine (mz-18 HoTT) or 12 (mz-
24 HoTT) function inputs, see the defi nition of terms on
page 37, of a mz-18 HoTT TEACH transmitter, and
up to 12 function inputs of a mz-24 HoTT TEACH
transmitter to the PUPIL transmitter either individually or
in any desired combination.
The TEACH value fi elds or buttons identify the
function inputs to which the control functions 1 … 4
(control stick functions for fi xed-wing and helicopter
models) are assigned, as well as the freely assignable
inputs 5 … max. 12 of the "Channel set" menu.
Note:
It does not matter which specifi c controls are
assigned to the control function inputs to be
transferred to the PUPIL. They can only be
assigned in the "Channel set" menu when the trainer
connection is switched off.
Use a fi nger or the provided stylus to touch the control
function inputs 1 to max. 12 to be transferred to the
PUPIL, for example:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
PUPIL
PUPIL
PUPIL
PUPIL
TEACH
TEACH
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
NULL
OFF
RF
CTL
BIND
TYPE
Observe the standard conventions when assigning
control functions:
Channel Function
1 Motor/airbrake or pitch
2 Aileron or roll
3 Elevator or elevation
4 Rudder or tail rotor
To make the transfer, you need to assign a trainer switch
in the value fi eld under "CTL" at the right of the display,
as described in the section "Control, switch and control
switch assignment" on page 38.
It is preferable to use an intermittent switch such as S8
so that you can withdraw the control from the trainer at
anytime:
BACK
Graubele
SERVO
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
PUPIL
PUPIL
PUPIL
PUPIL
TEACH
TEACH
CH 7.
CH 8.
CH 9.
CH 10.
CH 11.
CH 12.
TEACH
TEACH
TEACH
TEACH
TEACH
TEACH
SW8
OFF
RF
CTL
BIND
TYPE
Since at this early point in the trainer system
programming an operable PUPIL transmitter will not
107
Function menu - Trainer
S1006_mz-24.3.en.indd 107 17.12.2014 15:21:57