OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
Contents ◎ BEFORE USE Thank you for purchasing T5/mz-10 HoTT 2.4GHz Radio System. This system is extremely 2P SUPPORT AND SERVICE 2P while using your system, please consult the manual, our online Frequently Asked Questions (on - Customer support 2P the web pages referenced below), your hobby dealer, or the Graupner/SJ Service Center.
NOTICE ◎ FEATURES All instructions, warranties and other collateral documents are subject to change at the sole discretion of Graupner/SJ. For up-to-date product literature, visit http://www.openhobby.com and click on the support tab for this product. 5 channels radio control set with Graupner/SJ HoTT 2.
◎ TRANSMITTER CONTROL IDENTIFICATION TX Handel Antenna RF Trainer Switch 5 Channel Switch Dual Rate Switch Neck Strap Lug Rudder and Elevator Stick Throttle and Elevator Trim Throttle Trim Battery Cover Aileron Stick Power Switch Rudder Trim Aileron Trim Mode Button Direction Button Bind LED Wing Mix LED Channel Reverse LED Charge Socket Data Pin 4
◎ WHAT IS HoTT ◎ ADJUSTBLE STICK LENGTH The control stick is consisted of 2pc of stick levers and it allows you to adjust the control stick’s length as you want. 1. Hold the lever“B”and turn the lever“A” counter clockwise The lock will be released. Lever“A” 2. Turn the lever“B”and adjust the control stick’s length as you want. Turn the lever“A” clockwise, then the lever“A”and“B”are interlocked and fixed.
. Dual Rate 4. Binding You must bind the receiver to the transmitter before the receiver will operate. Binding teaches the receiver the specific code of the transmitter so that it will only connect to it’s corresponding transmitter. 1. Switch on the transmitter and receiver. 2. Press & hold the SET button on the receiver for over 3 sec until the receiver enters BIND mode. 3. Press the MODE button on the transmitter, the system will be connected within a few seconds.
1-2. Failsafe mode - FAILSAFE Move the control sticks on the transmitter to the desired preset failsafe positions. Press & hold the MODE button for over 2 sec and release the button. The Graupner/SJ logo turns solid red, indicating the failsafe mode has been set. Confirm the failsafe setting is correct by turning off the transmitter. The throttle should go to the preset position. - HOLD Function setting LED Enter hold mode by pressing MODE button once from the failsafe mode.
1-2. Pupil setting When using the T5/mz-10 as the pupil transmitter, bind the receiver at the NORMAL mode first. Turn off the transmitter, and still the receiver is turned on, and move transmitter’s RF TRAINER SWITCH to PUPIL position. Press & hold the MODE button and switch on the transmitter. The Graupner/SJ logo repeats to blink a single red with a single beep, indicating that you set PUPIL Mode. After one beep sound twice, a beep doesn’t sound.
◎ SMART BOX When using the optional smart box, the transmitter’s functions can be easy to set up and check the telemetry data. Connect into the DATA socket at the back of the transmitter and switch on the transmitter.
◎ SAFETY APPROVAL Declaration of Conformity (in accordance with ISO/IEC 17050-1) - Product(s): Graupner/SJ T5/mz-10/mz-10 Transmitter Item Number(s): Equipment class: 2 The objects of declaration described above are in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/ EC: EN 62479:2010 EN 60950-1:2006/A11:2009/A1:2010/A12:2011 EN 301 489-1 V1.9.2 EN 301-489-17 V2.2.1 EN 300 328 V1.7.
Caution • This equipment’s aerial must be at least 20 cm from any person when the system is in use. We therefore do not recommend using the equipment at a closer range than 20cm. • Ensure that no other transmitter is closer than 20cm from your equipment, in order to avoid adverse effects on the system’s electrical characteristics and radiation pattern. • The radio control system should not be operated until the Country setting has been set correctly at the transmitter.
