LDX 100 User’s Guide Function: Values: VideoMode Usr: Description: Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 1080p59, 1080p50, 4K59, 4K50, 4K47, 4K29, 4K25, 4K23 Video RX 2 Stream Active Yes, No 1 Pkts in Buffer 1 VideoMode Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 1080p59, 1080p50, 4K59, 4K50, 4K47, 4K29, 4K25, 4K23 Video RX 3 Stream Active Yes, No 1 Pkts in Buffer 1 VideoMode Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 10
Menu references Diagnostics menu Function: Values: Usr: Path Delay 1 Offset to Master -30000..30000 (0) 1 Prio 1 0..255 (0) 1 Prio 2 0..255 (0) 1 Class 0..255 (0) 1 Accuracy 0..255 (0) 1 ID ??? 1 IP ??? 1 Status Listening, Calibrating, Locked, Off 1 Path Delay 1 Offset to Master -30000..30000 (0) 1 Prio 1 0..255 (0) 1 Prio 2 0..255 (0) 1 Class 0..255 (0) 1 Accuracy 0..255 (0) 1 Priority 0..
LDX 100 User’s Guide Function: VideoMode Values: Usr: Description: Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 1080p59, 1080p50, 4K59, 4K50, 4K47, 4K29, 4K25, 4K23 Extern 2 Available Yes, No 1 VideoMode Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 1080p59, 1080p50, 4K59, 4K50, 4K47, 4K29, 4K25, 4K23 Extern 3 Available Yes, No 1 VideoMode Unknown, SD, 1080i59, 1 1080i50, 720p50, 720p50, 1080pfs23, 1080p59, 1080p50, 4K59, 4K50, 4K47, 4K29, 4K25, 4K23 BNC-D Availa
Menu references Diagnostics menu Function: Values: Usr: Cable Status OK, Critic, Error, NoSig 0 Signal Status OK, Critic, Error, NoSig 0 RX Margin -100 dB..100 dB (0 dB) 0 Signal Error Cnt 0..65535 (50) 0 Cable Status OK, Critic, Error, NoSig 0 Signal Status OK, Critic, Error, NoSig 0 RX Margin -100 dB..100 dB (0 dB) 0 Signal Error Cnt 0..
LDX 100 User’s Guide Function: Values: Usr: Stream Locked S Stream RxBuf_1 S Stream RxBuf_2 S Stream RxBuf_3 S Description: Streams Tx Available S Tx Not Used S Rx Requested S Rx Subscribed S Ethernet Tunnel MDIO S SGMII S PhySpeed S Tunnel Active S CAM S XCU S Rx Packets S Tx Packets S C2IP Trunk Rx Packets S Tx Packets S Audio FrontMic Lvl -127..0 (-127) 0 ??? Audio1 Lvl -127..0 (-127) 0 ??? Audio2 Lvl -127..0 (-127) 0 ??? Audio3 Lvl -127..
Menu references Diagnostics menu Function: Values: Usr: ??? 2 Code ??? 2 Version ??? 2 Warning None, Front, Head, Mpb Fpga, Txb Fpga, Fan, Fan+T, !STOP! 2 Fan Mode Off, Var, Manual 2 Fan Profile Silent+, Silent, Default, 2 Cool Manual Speed 3000 rpm..9000 rpm (6000 rpm) 2 Camera -128 C..127 C (0 C) 2 MPB FPGA -128 C..127 C (0 C) 2 -128 C..127 C (0 C) 2 TXB FPGA -128 C..127 C (0 C) 2 Front -128 C..127 C (0 C) 2 Sensor Red -128 C..127 C (0 C) S Sensor Green -128 C..
LDX 100 User’s Guide Function: Values: Usr: -128 C..127 C (0 C) 2 Camera -197 F..261 F (0 F) 2 MPB FPGA -197 F..261 F (0 F) 2 -197 F..261 F (0 F) 2 TXB FPGA -197 F..261 F (0 F) 2 Front -197 F..261 F (0 F) 2 Sensor Red -197 F..261 F (0 F) S Sensor Green -197 F..261 F (0 F) S Sensor Blue -197 F..261 F (0 F) S -197 F..261 F (0 F) 2 Backpanel Description: Temp (F) Sitara Backpanel Front PID 2 Code 2 Status 0..255 (0) 2 0 dB..6 dB (0 dB) S 0 dB..6 dB (0 dB) S 0 dB..
Menu references Diagnostics menu Function: 140 Values: Usr: State ??, NoAccess, Recovered, Init, Valid S Oper.Hours 0..65535 (0) S Oper.Hours (SXP) 0..65535 (0) S Power Cycles 0..65535 (0) S Minimum Temp -128 C..127 C (0 C) S Maximum Temp -128 C..127 C (0 C) S High Temp Warn. 0..
LDX 100 User’s Guide Service menu Function: Values: U: F: Description: Colour bar Off, On 3 - Enable/disable color bar Test Signal Off, On 3 - Enable/disable test signal Test Select SawT, Step 3 - Select Sawtooth or Stepped signal Exec, Busy S - ??? Camera AppLog No, Yes S - Select Yes to include Camera Applog in diagnostics file Config Info No, Yes S - Select Yes to include Camera Config in diagnostics file Settings Info No, Yes S - Select Yes to include Settings Info in diagn
Menu references Service menu Function: Values: U: F: Description: 3200K Calibr Off, On S - Select to run 3200K Calibration 3200K Reset Fact, Cust S - Resets 3200K Calibration data Vref Calibr Off, Running S - Select to run Vref Calibration Status Unknown, Ok, Ready, Busy, Error, Abort, Filter Cap S - Shows status of Vref Calibration Progress 0%..
Connectors Right front side Bottom view Lens connector viewFront finder Mic connector connecor 143
Connectors Front microphone connector Front microphone connector 1 3 Pin Description 1 Audio shield 2 Audio In (+)1) 3 Audio Return (-) Microphone impedance >200 Ω Nominal input level is adjustable from -22 dBu to -64 dBu in the camera menu. Phantom power (+48 V) on this socket can be switched on or off. 2 XLR 3-pin female connector (panel view) 1) Signal at pin 2 of audio input is in phase with signal at pin 2 of audio output.
LDX 100 User’s Guide Right side connector panel Ethernet IP/Trunk REF/AES BNC BNC A BNC B BNC C BNC D BNC E HDMI Ethernet Trunk/IP connector 8-pin standard RJ-45 ethernet connector (panel view) Pin Description 1 Transmit Data 1+ (TX_D1+ ) 2 Transmit Data 1- (TX_D1-) 3 Receive Data 2+ (RX_D2+) 4 BI_D3+ 5 BI_D3- 6 Receive Data 2- (RX_D2-) 7 BI_D4+ 8 BI_D4- Ethernet 10/100/1000 Base-T compliant with IEEE-802.
Connectors REF/AES connector REF/AES connector Can be programmed for Reference input, AES (AES digital audio) input, or TriLvl, Composite reference. BNC connector (panel view) Go to the Configuration > Signals > BNC Ref/AES setting to change the signal for this connector. BNC A to E connectors These BNC connectors can be programmed for different video output signals (1.5G, 3G or 12G). Refer to the table below for the options.
LDX 100 User’s Guide Back panel Hybrid fiber transmission connector C2IP connector SERVICE ONLY C2 IP RS-232 connector USB connector Intercom headset connector RS-232 TX LOCK AUX Auxiliary connector AUDIO 2 CTRL Audio 2 input DC IN 12-17V AUDIO 1 DC Power Output Audio 1 input DC OUT 12V 4A DC Power Input Hybrid fiber transmission connector 1 4 2 Pin Description 1 Optic Fiber channel A 2 Power supply return 3 Optic Fiber channel B 4 Power Manufacturer code: LEMO 3K.
Connectors USB connector USB connector 1 4 USB type A host connector (panel view) Pin Description 1 + 5 VDC 2 Data - 3 Data + 4 GND USB type A connector (host) compatible with USB 2.
LDX 100 User’s Guide DC Power input connector 4 3 2 1 Pin Description 1 GND 2 GND 3 +12 to +17 V 4 +12 to +17 V Pins 1 & 2 are bridged CAUTIONS: input voltage must not exceed 17 V total input current must be <= 16A Pins 3 & 4 are bridged XLR 4-pin male connector (panel view) DC Power output connector 4 3 2 1 Pin Description 1 GND 2 GND 3 +13 to +17 V 4 +13 to +17 V Pins 1 & 2 are bridged Pins 3 & 4 are bridged NOTE: DC Power is not available when the camera is locally powered
Connectors Auxiliary connector Auxiliary connector 1 20 20-pin Hirose female connector (panel view) Pin Description Pin Description 1 Return A 11 Tracker Microphone return 2 Return B 12 Tracker Microphone 3 Tracker intercom to Production 13 GND 4 Tracker intercom to ENG 14 Menu select 5 Tracker telephone left 15 Call indication 6 Tracker telephone return 16 GND 7 Tracker telephone right 17 Menu Up 8 not connected 18 Menu Down 9 Call switch 19 ISO indication 10 +1
LDX 100 User’s Guide RS-232 connector 6 1 2 5 4 3 6-pin Hirose female connector (panel view) Pin Description 1 GND 2 TxD1 (serial connection 1) 3 TxD2 (serial connection 2) 4 GND 5 RxD1 (serial connection 1) 6 RxD2 (serial connection 2) Serial connection 1: can be used for serial (private) data. Serial connection 2: can be used for camera control or pan and tilt systems. Signals are at RS-232 levels, 115 kB/s max.
Connectors C2IP Ethernet connector 152
Video signals XCU mode Configuration hybrid fiber 46 power LDX 100 Camera XCU Universe UXF Base Station To switch the camera to XCU mode, go to Installation > Camera Mode and select XCU. Baseband signals body IP Streams body NativeIP mode Configuration hybrid fiber 2x Single Mode fiber HPE power LDX 100 Camera HPE-300 Hybrid Power Extender Network Switch To switch the camera to NativeIP mode, go to Installation > Camera Mode and select IP.
Video signals IP Streams Broadcast 4K video modes Connector: 4K150/179 (3X) 4K50/59 (1X) “Phases” profile1) "Default" profile1) BNC-A Live combined out HDR (12 Gb/s) Live out HDR (12 Gb/s) BNC-B Phase 1 out HDR (12 Gb/s) Live out 1.5 Gb/s SMPTE 292M/296M or 3 Gb/s SMPTE 425-1 HDR or SDR2) BNC-C Phase 2 out HDR (12 Gb/s) Ext1, 2 or 3 (1.5 Gb/s, 3 Gb/s or 12 Gb/s)3) BNC-D Phase 3 out HDR (12 Gb/s) Ext1, 2 or 3 (270 Mb/s,1.
LDX 100 User’s Guide Incoming IP streams - 3X UHD HDR IP --> CAM @4:2:2; 10 bits @150/179 Hz; - 1X UHD HDR/SDR @4:2:2; 10 bits @50/59 Hz Bandwidth (100 G) single NIC Remarks: (In Native IP mode three video receivers are available. RX1: up to UHD RX2: up to UHD RX3: up to 1080p) ST211020@59.94 ST20226@59.94 UHD only as full raster 211020/21 Source >> Switcher Audio Icom Control Trunk Network connection: V1 I1 C1 T1 Return 1 @4:2:2; 10 bits@50/59 Hz 2160p or 1080p or 1080i 11.10 11.
Video signals Incoming IP streams PTP SMPT2059/ AES67 Precision time protocol, with BGM algorithm. SAP RFC2974 No support for announcements from other Dante nodes on the network. LLDP IEEE802.32012 LLDP is used as advertising only. No LLDP info available of switch port information AMWA/NMOS IS-04/ 05 AMWA NMOS IS-04/05 ARP RFC 826 IGMP V2/V3 RFC2236 /4604 Total ctrl/lock/mon tx: 0.
LDX 100 User’s Guide Outgoing IP streams 3X UHD HDR @4:2:2; 10 bits@150/179 Hz Native IP 100G CAM --> IP Bandwidth Bandwidth Remarks: (100G) (100G) The 100G media network Single NIC Single NIC interface is a single network Destination: Slomo Switch Audio er Icom Control Trunk Network connection: V2 V1 I1 C1 4K phase 1 HDR 2160p 11.10 SMPTE 2110-22 Only 4K phase 2 HDR 2160p 11.10 SMPTE 2110-22 Only 4K phase 3 HDR 2160p 11.10 SMPTE 2110-22 Only 2.
Video signals Outgoing IP streams 2K Live HDR/SDR 1080p or 1080i or 720p Total video tx: Audio/intercom CAM --> IP Destination: Slomo Switch Audio er Icom Control Trunk Network connection: V2 V1 I1 C1 Audio TX 2.77 3.20 13.87 14.30 All downscaling on Main processor board. HDR/SDR user defined. Bandwidth (25 G) A1 2110-30 T1 16 CH Intercom TX Support for 1 ch, 2 ch, 4 ch, 8 ch, 16 ch stream 16 CH Support for 1 ch, 2 ch, 4 ch, 8 ch, 16 ch stream Total Audio/int tx: 0.
LDX 100 User’s Guide IGMP V2/V3 Total Audio/int tx: RFC22 36/ 4604 0.
Video signals Outgoing IP streams 160
Procedures Licenses About licenses/options With Grass Valley licenses it is possible to temporarily or permanently add one or more extra options to your LDX 100 camera. Contact your local Grass Valley representative for information about the availability and prices of the different licenses. Installation procedure Licenses have the form of a .lic file which is a plain text file containing one or more licenses for one or more cameras.
Procedures Calibrations 4 Enter the FinD Licenses menu and select Search Next to start searching for licenses on the USB Flash Drive. • During the search process [...] is shown. 5 When a license is found, select Add License to install it. • License type, duration and start date (only for temporary licenses) are shown. • Up to 5 planned licenses are visible at the same time in the menu. More licenses can be installed; planned licenses show up when they become active.
LDX 100 User’s Guide How to apply To start the Black Calibration procedure proceed as follows: • Switch on power and camera and wait for the system to become fully operational. To ensure the best black performance, wait until the camera has reached its operational temperature. This may take up to 30 minutes, depending on the ambient temperature. ☞ The user level must be set to Service to access the Service menu.
Procedures Formatting the SD Card ☞ The results of the Full Black procedure are NOT stored in the camera’s internal memory: Note Note after switching off the camera the results are reset to their default values. Black Calibration affects all video modes within one of the following clusters of video modes: (720p+1080i+ 1080p in 1X speed), (720p+1080i+1080p in 3X speed) and 4K. The availability of video modes depend on installed licenses.
Installation of (Q)SFP modules (Q)SFP modules configurations Depending on the workflow the optical connections of the camera need to be properly installed. This is done through internal installation of (Q)SFP modules.
Installation of (Q)SFP modules Changing (Q)SFP modules ☞ The inside of the panel holds the cooling pads for the (Q)SFPs. Make sure that they stay in Note Note place and do not get deformed. Keep them free from dirt. • Remove the LC fiber(s) from the dummy SFP module. Make sure the cable (ferrule) ends keep clean. • Carefully remove the inserted (Q)SFP module(s) from their case(s). If two SFP modules are inserted, remove them one by one.
LDX 100 User’s Guide Configuration 1 (1x 25G SFP module) (also valid for 1x 10G/10G+25G dual-rate SFP module) • Remove • Insert fiber A into the top LC socket of the SFP module and insert fiber B into the bottom LC socket of the SFP module: QSFP cage SFP 1 cage SFP 2 cage Configuration 2 (2x 25G BiDi SFP modules) Insert fiber A into the top LC socket of the SFP module and insert fiber B into the top LC socket of the SFP module: QSFP cage SFP 1 cage SFP 2 cage 167
Installation of (Q)SFP modules List of (Q)SFP modules Configuration 3 (1x 100G QSFP module) • Remove the plastic protection cap from the QSFP module (if present). • Place the QSFP (without fibers) into the QSFP cage. • Insert fiber A into the top LC socket of the QSFP module and insert fiber B into the bottom LC socket of the QSFP module. QSFP cage SFP 1 cage SFP 2 cage • Reinstall the right side panel and tighten the four captive screws. Make sure that the screws are fixed hand-tight.
LDX 100 User’s Guide ☞ Make sure that the matching (‘other end’) (Q)SFPs in the IP switch have the same Note Note specifications.
Installation of (Q)SFP modules List of (Q)SFP modules 170
Specifications General Temperature range (operating): -20 °C to +45 °C (-4 °F to 113 °F) Weight: 6.05 kg (13.3 lbs) including handgrip and shoulderpad Dimensions (width x depth x height): 166.5 x 397.7 x 252.3 mm (6.56 x 15.66 x 9.93 in) Power consumption (typ.): 125 W Pick-up device: 3x 2/3” UHD Titan imagers Smear: no vertical smear Shutter: no mechanical shutter Optical system: F1.
Specifications Connectivity Connectivity 172 Microphone input (front): XLR-3 female, balanced, with switchable +48 V phantom power REF/AES BNC connector: Reference input,output or AES digital audio BNC A to E connectors: Video BNC baseband connectors (1.
LDX 100 User’s Guide 252.3 mm 93 mm 153.3 mm Dimensions 5 mm 92.7 mm 74 mm 166.5 mm 379.
Specifications Dimensions 174
Contact Us Grass Valley Technical Support For technical assistance, contact our international support center, at 1-800-547-8949 (US and Canada) or +1 530 478 4148. To obtain a local phone number for the support center nearest you, please consult the Contact Us section of Grass Valley’s website (www.grassvalley.com). An online form for e-mail contact is also available from the website. Corporate Head Office Grass Valley 3499 Douglas-B.
