DIGITAL AUTOMATIC BLOOD PRESSURE MONITOR USER MANUAL MODEL : MD5900 / MD5910 / MD5920 / MD5930 MD5940 / MD5950 / MD5960 / MD5970 MD5980 / MD5990
INTRODUCTION Thank you for purchasing this blood pressure monitor. Please read this manual thoroughly before use. Contact your physician if you have any queries about your blood pressure. This fully automatic instrument utilizes the non-invasive oscillometric method, which detects your blood movement through you brachial artery, for measuring your blood pressure and pulse rate, and the result will display on a digital panel. Without using a stethoscope, you can get the readings promptly and easily.
SAFETY NOTES WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. WARNING • Consult your physician before starting to measure your blood pressure.
SAFETY NOTES • Please note that technically related measuring tolerances are possible. Please see the section “TECHNICAL SPECIFICATION”. • Any cuff related blood pressure measurement in high repetition rates, can lead to severe measurement side effects, e.g. - A nerve compression with temporary wrist/ hand paralysis - The release of an arterial or venous thrombus, which can cause a life threatening situation. Please contact your physician about the specific risks of cuff pressure in your specific case.
SAFETY NOTES • Proper cuff size is important for accurate measurements. Only use the device on adults who have the right upper arm circumference for this unit. See “TECHNICAL SPECIFICATION” for suitable arm circumferences. • Electromagnetic interference: Avoid strong electrical or electromagnetic fields in the direct vicinity of the device (e.g. mobile phones, microwave ovens) while it is in operation, an inaccurate measurements may result.
SAFETY NOTES CAUTION • This device should not be used when your arm has been wounded/ injured or when a catheter has been inserted. Such use may result in injury. • Remove any kind of arm jewellery or the like before taking a measurement. This could cause bruises. • Do not place the arm cuff over heavy clothing (e.g.
MAINTENANCE AND STORAGE • The blood pressure monitor is constructed by precision electronic components. Accuracy of readings and the instrument’s service life depend on careful handling. Protect the unit against hard knocks (e.g. dropping the unit), moisture, water, dirt, dust, chemicals, extreme hot or cold temperatures, major temperature fluctuations, direct exposure to sunlight and heat sources which are too close (e.g. stoves, heating radiators). This may damage the unit.
PART IDENTIFICATION WHO Indicator Arm Cuff Display Air Connector Plug Start / Stop Button Index Mark Air Hose Air socket Memory Button USB port for power supply Battery Door 7
DISPLAY READINGS Battery Indicator Date Severe Hypertension Time AM PM Systolic Pressure Moderate Hypertension Bluetooth Icon Mild Hypertension Memory Average of Previous Measurement Diastolic Pressure Irregular Heartbeat Indicator High Normal Normal USER Optimal Pulse Rate 8
INSTALL/ CHANGE BATTERIES 1. Push the battery cover located on the bottom side on the unit as shown in the figure. 2. Remove old batteries and insert new ones. Use LR03 or AAA alkaline batteries and use batteries of the same type only. 3. Make sure the battery polarities (+) and (-) match the making on the battery compartment. 4. Place back the battery door. NOTE: • Insert the batteries as shown in the battery compartment. If not, the device will not work or even be damaged.
USING ADAPTOR (Accessory item sold separately) 1. Plug the power adaptor into a 100-240 V, 50/60Hz power socket. 2. Plug the Micro USB plug into the USB port at the device. Micro USB port is for power supply only. The USB port can’t be used for data downloading. 3. the optional adaptor shall comply with the requirement of standard IEC60601-1 and 2MOPP protection. USB Cable Power Adaptor Wall Socket NOTE: • If you need an adapter, you may purchase it separately.
TO SET DATE / TIME (Model: MD5900 / MD5910 / MD5940 / MD5950) When new batteries are installed 1. “YEAR” will blink on the display. 2. Press [M] key to set the current Year. 3. Press [ ] key to confirm and then "MONTH" will start to blink. 4. Press [M] key to set the current Month. 5. Press [ ] key to confirm and then "DAY" will start to blink. 6. Press [M] key to set the current Day. 7. Press [ ] key to confirm and then "HOUR" will start to blink. 8. Press [M] key to set the current Hour. 9.
TO SET DATE / TIME / LANGUAGE / VOLUME (Model: MD5920 / MD5930 / MD5960 / MD5970) When new batteries are installed 1. “YEAR” will blink on the display. 2. Press [M] key to set the current Year. 3. Press [ ] key to confirm and then "MONTH" will start to blink. 4. Press [M] key to set the current Month. 5. Press [ ] key to confirm and then "DAY" will start to blink. 6. Press [M] key to set the current Day. 7. Press [ ] key to confirm and then "HOUR" will start to blink. 8.
TO SET DATE / TIME / BLUETOOTH (Model: MD5980) When new batteries are installed Bluetooth “On” 1. “YEAR” will blink on the display. 2. Press [M] key to set the current Year. 3. Press [ ] key to confirm and then "MONTH" will start to blink. 4. Press [M] key to set the current Month. 5. Press [ ] key to confirm and then "DAY" will start to blink. 6. Press [M] key to set the current Day. 7. Press [ ] key to confirm and then "HOUR" will start to blink. 8. Press [M] key to set the current Hour. 9.
TO SET DATE / TIME / LANGUAGE / VOLUME / BLUETOOTH (Model: MD5990) When new batteries are installed 1. “YEAR” will blink on the display. 2. Press [M] key to set the current Year. 3. Press [ ] key to confirm and then "MONTH" will start to blink. 4. Press [M] key to set the current Month. 5. Press [ ] key to confirm and then "DAY" will start to blink. 6. Press [M] key to set the current Day. 7. Press [ ] key to confirm and then "HOUR" will start to blink. 8. Press [M] key to set the current Hour. 9.
TO APPLY ARM CUFF 1. Pass the end of the cuff furthest from the tubing through the metal ring to form a loop. The smooth cloth should be the inside of the cuff loop. 2. Put your left arm through the cuff loop. The bottom of the cuff should be approximately 2 – 3 cm above the elbow. The white artery mark on the cuff should lie over the brachial artery on the inside of the arm. The tube should run down the centre of arm and even with the middle finger. Do not place the arm cuff over heavy clothing (e.g.
BEFORE MEASURING BLOOD PRESSURE 1. Apply the arm cuff following the instruction in “TO APPLY ARM CUFF”. 2. Rest at least for 5 minutes before each measurement. Otherwise there may be erroneous results. 3. Sit down in a comfortable position, which your legs should be uncrossed, feet should be feet on the floor and your back should be supported by a chair. At the same time your arm should be supported on a flat surface which the cuff is on a level with your heart. 4. Relax your arm and turn your palm upward.
TO MEASURE YOUR BLOOD PRESSURE 1. Follow the instruction in “BEFORE MEASURING BLOOD PRESSURE” to make yourself ready. 2. Press [ ] button to turn the device from clock mode to standby mode. Press and hold [ ] button to enter user selection mode (Model: MD5940/ MD5950/ MD5960/ MD5970/ MD5980/ MD5990) Press [M] button to to select user memory 1 or 2. Confirm selection by pressing [ ] button. Record number and User ID are displayed 3. Press [ ] to start the blood pressure measurement. 4.
PRESSURE BAR INDICATOR The indicator monitors the progress of pressure during measurement.
WHO CLASSIFICATION INDICATOR Each of the six segments of the bar indicator corresponds to the WHO blood pressure classification.
TO RECALL AVERAGE AND PREVIOUS MEASUREMENT DATA This device has a memory capability to store the measurement readings for each user. Every time you complete the measurement, the device automatically stores the measurement result. 1. Press [M] button in standby mode to enter the memory mode, the average blood pressure for all measurements is displayed. 2. Press [M] button to view average data for lastest 7 days AM record (5:00 - 9:00 am). 3.
TO DELETE MEASUREMENT DATA 1. Press [M] button simultaneously when the device is showing average or previous measurement data of selected user. 2. Press and hold [M] button for 5 seconds until [CL] [--] are shown. 3. Press [M] button to confirm and [CL] [00] are shown. All measurement data for the selected user will be deleted.
TRANSFER MEASUREMENT DATA TO SMART DEVICE (Model: MD5980 / MD5990) For the first time use 1. Download and install the free “G.LAB Health” app on your smart device. 2. Turn on the Bluetooth feature of the smart device. 3. Open the “G.LAB Health” app on your smart device and sign up a new account. 4. Make sure the Bluetooth feature of the monitor is on. To turn on/off the Bluetooth feature of the monitor, press [ ] or [M] button to standby mode. Press and hold [M] button to enter the setting mode. 5.
WHAT IS AN IRREGULAR HEARTBEAT This blood pressure monitor provides a blood pressure and pulse rate measurement even when an irregular heartbeat occurs. An irregular heartbeat is defined as a heartbeat that varies by 25% from the average of all heartbeats during the blood pressure measurement. It is important that you are relaxed, remain still and do not talk during measurements. NOTE: • We recommend you to contact your physician if you see this [ ] indicator frequently.
ABOUT BLOOD PRESSURE What Is Blood Pressure? Blood pressure is the force exerted by blood against the walls of the arteries. Systolic pressure occurs when the heart contracts. Diastolic pressure occurs when the heart expands. Blood pressure is measured in millimeters of mercury (mmHg). One’s natural blood pressure is represented by the fundamental pressure, which is measured first thing in the morning while one is still at rest and before eating.
TROUBLESHOOTING Batteries are drained Replace all batteries with new ones Battery polarities are not in the correct position Re-install the batteries with their negative and positive ends matching their indicated in the battery compartment Loose in plug or contact with outlet (IF AC adaptor is used) Check the wiring to make sure plug & outlet are properly secured The cuff position is not correct Sit comfortably and still.
TROUBLESHOOTING The unit does not measure If you have a very weak or irregular heart beat, the device may have difficultly in determining your blood pressure There is a measuring Error Sit comfortably and still. Fasten the cuff again carefully ERROR code 5 (E5) appears Cuff over inflated The measurement range is over 300 mmHg. It is recommended to see the doctor as soon as possible. ERROR code 6 (E6) appears Low battery The battery power is too low to function. Replace the batteries with new ones.
TECHNICAL SPECIFICATION Display Measurement Range Accuracy Resolution Measurement Method Power Source Optional AC Adaptor Service Life Operating Temperature / Humidity Storage Temperature / Humidity Operation, storage and transport atmospheric pressure Outer Dimensions Arm Circumference Accessories Classification Key to symbols : LCD Display : Systolic Pressure: 60-250 mmHg ; Diastolic Pressure: 30-200 mmHg Pulse : 40-180 beats/minute ; Cuff Range: 0-300mmHg : Pressure : +/-3 mmHg Pulse : +/-5% of reading
SYMBOLS Function / Meaning Symbols SN Serial Number Manufacturer Type BF: Device, cuff and tubing are designed to provide special protection against electrical shocks.
Appendix I Guidance and manufacturer’s declaration - electromagnetic emissions The Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/ MD5990) is intended for use in the electromagnetic environment specified below. The customer or the user of the Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/ MD5990) should assure that it is used in such an environment.
Appendix II Guidance and manufacturer’s declaration - electromagnetic Immunity The Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) is intended for use in the electromagnetic environment specified below. The customer or the user of the Sphygmomanometer (MD5900/ MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) should assure that it is used in such an environment.
Appendix III Guidance and manufacturer’s declaration - electromagnetic Immunity The Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) is intended for use in the electromagnetic environment specified below. The customer or the user of the Sphygmomanometer (MD5900/ MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) should assure that it is used in such an environment.
Appendix IV Recommended separation distances between portable and mobile RF communications equipment and the Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) The Sphygmomanometer (MD5900/MD5910/MD5920/MD5930/MD5940/MD5950/MD5960/MD5970/MD5980/MD5990) is intended for use in the electromagnetic environment specified below.
Appendix V This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Appendix VI WARNING • If any：a list of all cables and maximum lengths of cables (if applicable), transducers and other ACCESSORIES that are replaceable by the RESPONSIBLE ORGANIZATION and that are likely to affect compliance of the ME EQUIPMENT or ME SYSTEM with the requirements of Clause 7 (EMISSIONS) and Clause 8 (IMMUNITY). ACCESSORIES may be specified either generically (e.g. shielded cable, load impedance) or specifically (e.g. by MANUFACTURER and EQUIPMENT OR TYPE REFERENCE).
Symbol for the marking of electrical and electronics devices according to Directive 2002/96/EC. The device, accessories and the packaging have to be disposed of waste correctly at the end of the usage. Please follow Local Ordinances or Regulations for disposal. Grandway Technology (Shenzhen) Limited No. 5, the Second Industrial Zone, Zhukeng Community, Longtian Street, Pingshan District, Shenzhen, 518118 The People’s Republic of China Shanghai International Holding Corp.
