Grandstream Networks, Inc.
GXV3601 IP Camera Safety Instructions These instructions are intended to assist users with the operation of the GXV3601 and also to instruct on how to avoid dangerous situations or damage to the device. Warnings: Serious injury or death may be caused if any of the warnings below are neglected. Cautions: Injury or damage to the equipment may occur if any of the following caution messages are neglected. Warnings Follow these safeguards to prevent serious injury or death.
GXV3601 IP Camera Contents Welcome .........................................................................................................................................................4 Package Contents ............................................................................................................................................5 Product Overview ...........................................................................................................................................
GXV3601 IP Camera Welcome The GXV3601 is a next generation IP camera for remote monitoring and surveillance over your LAN or internet. The GXV3601 combines best in class IP video technology and SIP protocols for a robust IP surveillance solution. The product features H.264 video streams with up to 30 frames per second in full D1, delivering rich image clarity at rapid transmission rates.
GXV3601 IP Camera Package Contents Items in the package: • • • • GXV3601 IP Camera 12V DC power Adapter 6-pin terminal block connector – 6-pin connector block for connecting external devices, such as infrared detector, smoke detector and etc., to Alarm IN, Alarm OUT and RS485 pins. Quick installation guide Firmware 1.0.4.6 Grandstream Networks, Inc.
GXV3601 IP Camera Product Overview GXV3601 Overview TABLE 1: GXV3601 PRODUCT MODELS Model GXV3601-N GXV3601-HD GXV3601-LL P/N xxx-xx004-xxx xxx-xx009-xxx xxx-xx0011-xxx GXV3601 Side View- (This is only applicable on GXV3601-N) Firmware 1.0.4.6 Grandstream Networks, Inc.
GXV3601 IP Camera GXV3601_LL and GXV3601_HD have no DC driver IRIS GXV3601 Back Panel Indicators and Connectors on Back Panel NETWORK – 10/100 Switch LAN port for connecting to Ethernet. The indicator will be steady for connection and flashing for network activity. AUDIO IN – 3.5mm port for audio input devices (microphone, pickup and etc.). AUDIO OUT – 3.5mm port for audio output devices (speakers, and etc.). VOUT – 1 BNC (Voltage: 1.0V p-p, Resistance 75Ω) port for video output.
GXV3601 IP Camera POWER – The indicator will be solid green if the power is on. GXV3601 Sample Connection Diagram GXV3601 Key Features The table below lists the key features the GXV3601 Supports. Features GXV3601-N GXV3601-HD GXV3601-LL Image Sensor 1/3” Sony Supper HAD CCD 1/3.2”, 2-Megapixel CMOS, 1,600H x 1,200V 1/4”, CMOS, 680H x 512V digital and NTSC/PAL analog outputs Lens Type 1/3” Varifocal 3.5-8mm, CS mount, changeable 1/3”, 3.5-8mm, F1.4, Mega Manual-Iris, CS 1/3”, 3.5-8mm, F1.
GXV3601 IP Camera 720x576 (PAL D1), 352x288 (PAL CIF), 172x144 (PAL QCIF) Max Frame Rate in Max 30fps/25fps at D1 resolution (NTSC/PAL) 20fps for 1,600x900, 30fps for 1,280 x 720, 30fps for 800x450, 640x360, 480x270, 320x180 and 240x135 30fps for VGA & NTSC, 25fps for PAL Video Bit Rate 32 Kbps – 2 Mbps 32 Kbps – 4 Mbps, adjustable (8 Mbps maximum) 32 Kbps – 2 Mbps Video Output 1BNC ( voltage1.0Vp-p, resistance75) N/A 1BNC ( voltage1.0Vp-p, Audio Input Audio Output 3.5mm LINE IN 3.
GXV3601 IP Camera Compliance FCC Part15, Subpart B Class B; EN 55022 Class B, EN61000-3-2, EN61000-3-3, EN 55024, EN60950-1; C-tick AS/NZS CISPR 22, CISPR 24 GXV3601 Lens Specification Parameters GXV3601-N GXV3601-LL GXV3601-HD Lens Mount Lens Format CS 1/3” CS 1/3” CS 1/3” Mega Focal Length Variable focus, 3.5 to 8.0 mm Variable focus, 3.5 to 8.0 mm Variable focus, 3.5 to 8.0 mm 8.28~13.38mm 8.28~13.38mm 1/1.4 1.4~360 1.4~360 Horizontal View Angle IRIS 81 o DC Iris 16.
GXV3601 IP Camera GXV3601 Recommended Lens Specification Parameters Lens Mount CS Recommendation CS mount is commonly used C C/CS adapter ring is needed for C mount Lens Format 1/3” Focal Length Fixed Focus Variable Focus f = 4 mm, f = 6 mm, or f = 8 mm f = 3 to 8 mm; f = 5 to 55 mm Aperture (D/f’) Constant Aperture F = 1.2, F = 1.6 Variable Aperture F1.
GXV3601 IP Camera Installation Guide Minimum Recommended System Requirement • • • • Windows 2000 Server Professional, Windows XP, Windows Vista. CPU: Intel Pentium 4 or higher, 2 GHz. RAM: 1 GB (4 GB recommended for larger systems). Support for DirectX 8.0 and above. . Connect your GXV3601 Using the Power adapter as power supply • • • • Connect an RJ-45 cable to the NETWORK port of the GXV3601. Connect the other end of the RJ-45 cable to your network or PC.
GXV3601 IP Camera Configuring the GXV3601 via Web Browser The GXV3601’s embedded Web server responds to HTTP/HTTPS GET/POST requests. Embedded HTML pages allow you to configure your IP camera through Microsoft Internet Explorer. Access GXV3601 Web Configuration Menu Connect the Camera to DHCP server. 1. Navigate your browser to: http://www.grandstream.com/support/gxv_series_surveillance/general/resources/gs_ search.zip 2. Run the Grandstream GS_Search tool, that you just downloaded.
GXV3601 IP Camera Connect to the Camera using Static IP. If the camera does not get response from DHCP server after 3 minutes, it can be accessed by the default IP 192.168.1.168. 1. Connect your PC to the same network as the GXV3601. 2. Configure the IP address of your PC to: 192.168.1.XXX (1
GXV3601 IP Camera GXV3601 Home Web Page Figure2: Home web page of GXV3601-N and GXV3601-LL Figure3: Home web page of GXV3601-HD Firmware 1.0.4.6 Grandstream Networks, Inc.
GXV3601 IP Camera Items on GXV3601 Home Page 1 Motion Detection 2 Alarm Event 3 4 5 6 Control Console ZOOM FOCUS Default 7 8 9 10 11 SPEED BRIGHTNESS CONTRAST SATURATION View Size 12 13 Play Capture 14 Record 15 16 17 18 Sound Off/On Talk Playback Config If the motion detection alarm is triggered, the indicator will flash red. Click on the indicator to turn off the alarm. If an alarm event is triggered, the indicator will flash red. Click on the indicator to turn off the alarm.
GXV3601 IP Camera host name. And you can select your time zone from the drop-down list or define your own time zone setting. NOTE: If using a host name for the NTP server, a DNS server must be configured under Basic Settings -> Networking. Synchronize with Local Computer - sets the time from the clock on your computer. Set the Time Manually - this option allows you to manually set the time and date.
GXV3601 IP Camera Resolution – The higher the resolution is, the better the video quality is, and higher bandwidth is required. Low -----------------------Æ High Resolution QCIF CIF 2CIF D1 Bit Rate – The number of bits that are conveyed or processed per unit of time. Maximum Frame Rate – The video frame rate is adjustable based on network conditions. Increasing the frame rate will increase the amount of data significantly therefore consuming more bandwidth.
GXV3601 IP Camera compression is a form of data compression designed to reduce the size of audio files. Usually, the higher the audio compression is, the better the audio quality is. Power Frequency - this setting should match the power frequency used in the country to avoid flickering in the image. And it is only available for GXV3601HD GXV3601 Networking Page – Assign an IP to GXV3601 GXV3601 supports IP version 4.
GXV3601 IP Camera port number is needed to access the web GUI, for instance: http://192.168.1.168:8080. NOTE: If the HTTP Port is 80, when you add this device to GSurf or GS_NVR, the RTSP port is 554. If the HTTP Port is changed, when you add this device to GSurf or GS_NVR, please make sure the RTSP port number equals HTTP Port plus 2000. GXV3601 Wifi Page – GXV3601 supports WIFI via wireless dongles. Enable Wifi – Checked to enable Wifi SSID – Click on Scan to view available network.
GXV3601 IP Camera STUN Server – If the device is behind a router, a STUN server is needed to help penetrate the NAT. 4. Click Save to save the changes. You might need to reboot the device to apply all the changes. GXV3601 SIP Page The GXV3601 has the ability to receive phone calls and make phone calls when an alarm event is triggered through motion detection or alarm input. Register the GXV3601 to a SIP server to enable the product to make and receive phone calls.
GXV3601 IP Camera 5. STUN Server – If the device is behind a router, a STUN server is needed to help penetrate the NAT. Stream – To choose between Primary and Secondary stream. Preferred Vocoder – To choose different Vocoder type. Registration Expiration – This parameter allows users to specify the time frequency (in minutes) in which the GXV refreshes its registration with the specified registrar. The default interval is 60 minutes.
GXV3601 IP Camera NOTE: With current firmware, only the first phone number in the list will be called when an alarm is triggered. GXV3601 Status Page System Statistics System Statistics lists hardware and software information, for example, the part number, the software version, about the GXV3601. Hardware Version – This field contains the product’s hardware information. Part Number – This field contains the product part number information. Bootloader Version – Bootloader code version number.
GXV3601 IP Camera GXV3601 User Management Page All current users will be list in the User List section of this page. You can also add and remove users here. Existing User Name –The field lists all of the current users. You can insert or remove users from the list by click on the Add or Update or Delete button. User Name / Password – The user name and password required to login. Privilege – The privilege for the user to access to configuration page.
GXV3601 IP Camera Automatic Upgrade – The default setting is “No.” Choose “Yes” to enable automatic. HTTP/HTTPS/TFTP upgrade and provisioning. When set to “No”, the IP Camera will only perform a HTTP/HTTPS/TFTP upgrade and perform a configuration check once during the boot process. Performing a firmware upgrade: 1. Download the firmware package from http://www.grandstream.com/firmware.html. 2. Unzip the firmware package and copy the files to the firmware upgrade server directory.
GXV3601 IP Camera SSL – Checked if the SMTP server requires a secure connection. Test Email Account Settings – Click the Test button to send a test email from the From E-Mail to the To E-Mail to make sure that SMTP is configured properly. If the receiver can get the test email, then the SMTP settings are ready to go. GXV3601 FTP Page The FTP server is used to store video files if you configure the GXV3601 to record video and upload it to the FTP server when an alarm event or motion detection is triggered.
GXV3601 IP Camera per second in a digitally modulated signal or a line code. Connect a PTZ device to the GXV3601 1. Connect the PTZ device to GXV3601 by following the connection diagram shown below 2. Click Advanced Settings > PTZ; in PTZ page, configure the PTZ Protocol and Baudrate according to your connected PTZ device. 3. Click Save and reboot the device to apply all changes. 4. Use those PTZ buttons on the homepage to tilt, pan the GXV3601 and also adjust the speed.
GXV3601 IP Camera than 15V, this will damage the IP camera. Internally, the Alarm-out uses relays as a switch (30VAC/2A); users can connect devices such as alarm siren or alert light to this port. Under normal circumstances, the circuit is open. When there is an alarm event, the GXV3601 will close the circuit to trigger the alarm. Connect Alarm Input Equipment to the GXV3601 Here are two sample connection diagrams. Connect the alarm equipment to the GXV3601 by following the diagram below.
GXV3601 IP Camera files: SD card, USB Flash drive, or USB hard drive. Voice Alarm to SIP Phone – If this option is selected, the GXV3601 will make calls to the number listed in the Phone List page using the configured SIP account when an alarm is triggered. To use this function, the settings in SIP page must be configured properly. Alarm Output – If this option is selected, the alarm will output via the configured method/equipment when it is triggered.
GXV3601 IP Camera GXV3601 Motion Detection Page The GXV3601 supports Motion Detection. To utilize this feature, please follow the below steps: 1. Setup the motion detection monitored area. 2. Configure the motion detection time schedule. 3. Configure alarm action properly. Setup Motion Detection Monitored Area Enable Motion Detection – If this option is selected, motion detection will be enabled. If something/somebody moves in the motion detection region, an alarm will be triggered.
GXV3601 IP Camera To Edit a Monitored Area 1. In the Select a Region dropdown list, select the region ID. 2. Click Edit. 3. Click on the video, drag and draw you preferred area. 4. Set the Sensitivity. Click the Save button to save the sensitivity. NOTE: The Sensitivity value varies from 0 to 100. The larger the value is, the higher the sensitivity. 5. Click Save to save the settings. Button to save sensitivity only To Remove a Monitored Area 1.
GXV3601 IP Camera GXV3601 System Log This page is used to set up the system log server path and system log level. Once they are correctly configured, the device will send out system log messages to the system log server, which will help perform troubleshooting. Syslog Server – The IP address or URL of System log server. Syslog Level – Select the device to report the log level. Default is None. The level is one of Debug, Info, Warning or Error.
GXV3601 IP Camera IP VIDEO SURVEILLANCE FAQ 1. What is the default IP address of GXV3601/3501/3504? Prior to firmware version 1.0.3.9, the IP address of GXV3501/ 3504/ 3601/ 3611 is 192.168.1.168 at the factory default settings. You can perform a factory reset by pressing the RESET button on the device for 7 seconds. Starting from firmware version 1.0.3.9, the default IP configuration is DHCP. 2.
GXV3601 IP Camera 6. Why does IE indicate to install Grandstream Video Viewer add-on after a firmware upgrade? The add-on was properly installed before the firmware upgrade process. New firmware will often upgrade the add-on as well. To watch the live video stream, you must install the newest version of the add-on. 7. How do you watch secondary video stream? Login to the home page of the GXV3501/ 3504/ 3601 web GUI, click Play to watch the video stream.
GXV3601 IP Camera You must set the video resolution to QCIF to watch the GXV3501/3504 /3601 video stream from a cell phone. Make sure to set the bit rate to 64kbps to ensure the best video quality. 14. Why doesn’t the IP address of the device reset when I click the “Restore” button on the Maintenance page? The GXV3501 /3504 /3601 could be installed in areas that are not easy to access. For example, it could be installed on the roof of a building or the ceiling of an office.
GXV3601 IP Camera 7. Tested PC display adapters.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC 15.
