Reinforced Inside Ladder Instructions Instructions Manual PNEG-1652 Version: 1.
PNEG-1652 Reinforced Inside Ladder Instructions
Table of Contents Contents Chapter 1 Safety .....................................................................................................................................................4 Safety Guidelines .................................................................................................................................. 4 General Safety Statement .....................................................................................................................
1. Safety Safety Guidelines This manual contains information that is important for you, the owner/operator, to know and understand. This information relates to protecting personal safety and preventing equipment problems. It is the responsibility of the owner/operator to inform anyone operating or working in the area of this equipment of these safety guidelines. To help you recognize this information, we use the symbols that are defined below. Please read the manual and pay attention to these sections.
1. Safety General Safety Statement Our foremost concern is your safety and the safety of others associated with grain handling equipment. This manual is to help you understand safe operating procedures and some problems that may be encountered by the operator and other personnel. As owner and/or operator, you are responsible to know what requirements, hazards and precautions exist and inform all personnel associated with the equipment or in the area. Safety precautions may be required from the personnel.
1. Safety Safety Instructions Our foremost concern is your safety and the safety of others associated with this equipment. We want to keep you as a customer. This manual is to help you understand safe operating procedures and some problems that may be encountered by the operator and other personnel. As owner and/or operator, it is your responsibility to know what requirements, hazards, and precautions exist, and to inform all personnel associated with the equipment or in the area.
1. Safety Prepare for Emergencies Be prepared if fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone. Keep Emergency Equipment Quickly Accessible Wear Protective Clothing Wear close-fitting clothing and safety equipment appropriate to the job. Eye Protection Remove all jewelry. Tie long hair up and back. Gloves Wear safety glasses at all times to protect eyes from debris.
2. Safety Decals Roof Damage Warning and Disclaimer The manufacturer does not warrant any roof damage caused by excessive vacuum or internal pressure from fans or other air moving systems. Adequate ventilation and/or “makeup air” devices should be provided for all powered air handling systems. The manufacturer does not recommend the use of downward flow systems (suction). Severe roof damage can result from any blockage of air passages.
2. Safety Decals ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring, 24" porthole door cover and the roof manway cover. If a decal has been damaged or is missing in any of these locations, contact the manufacturer for a free replacement decal. GSI Decals 1004 E. Illinois St. Assumption, IL. 62510 Phone: 1-217-226-4421 Rotating flighting will kill or dismember. Flowing material will trap and suffocate. Crusted material will collapse and suffocate.
2. Safety Decals ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring, 24" porthole door cover and the roof manway cover. If a decal has been damaged or is missing in any of these locations, contact the manufacturer for a free replacement decal. GSI Decals 1004 E. Illinois St. Assumption, IL. 62510 Phone: 1-217-226-4421 WARNING DON’T DO UNLOADING INSTRUCTIONS: 1. Use CENTER FLOOR OUTLET ONLY until NO grain remains above this outlet. 2.
3. Inside Ladder Instructions 2.66'' Commercial Stiffened Figure 3A Outside Stiffened NOTE: Be sure to push ladder sections up and tighten. Do not tighten ladder section splices with ladder sections hanging under their own weight. Now all standoff brackets and straps must be installed every 32" and attached to each 4' section required.
3. Inside Ladder Instructions Inside Ladder Bottom Bracket The bottom ladder section may need to be cut off if the length is too long. Cut the bottom section at least 12" from the bottom of the floor. Attach the bottom inside ladder brackets (LDR-5133) to the last ladder section using the six (6) holes per ladder rail. You may need to drill out the holes in the last ladder section with a 3/8" drill bit.
3. Inside Ladder Instructions 2.66'' Corrugated Farm Bin Figure 3E Inside Starter Bracket and Ladder Placement NOTE: Be sure to push ladder sections up and tighten. Do not tighten ladder section splices with ladder sections hanging under their own weight. Now all standoff brackets and straps must be installed every 32" and attached to each 4' section required.
3. Inside Ladder Instructions Inside Ladder Bottom Bracket The bottom ladder section may need to be cut off if the length is too long. Cut the bottom section at least 12" from the bottom of the floor. Attach the bottom inside ladder brackets (LDR-5133) to the last ladder section using the six (6) holes per ladder rail. You may need to drill out the holes in the last ladder section with a 3/8" drill bit.
3. Inside Ladder Instructions 4.00'' Commercial Stiffened Figure 3I Inside Starter Bracket and Ladder Placement NOTE: Be sure to push ladder sections up and tighten. Do not tighten ladder section splices with ladder sections hanging under their own weight. Now all standoff brackets and straps must be installed every 44" and attached to each 4' section required.
3. Inside Ladder Instructions Inside Ladder Bottom Bracket The bottom ladder section may need to be cut off if the length is too long. Cut the bottom section at least 12" from the bottom of the floor. Attach the bottom inside ladder brackets (LDR-5133) to the last ladder section using the six (6) holes per ladder rail. You may need to drill out the holes in the last ladder section with a 3/8" drill bit.
3. Inside Ladder Instructions 4.00'' Corrugated Farm Bin Figure 3M Inside Starter Bracket and Ladder Placement NOTE: Be sure to push ladder sections up and tighten. Do not tighten ladder section splices with ladder sections hanging under their own weight. Now all standoff brackets and straps must be installed every 44" and attached to each 4' section required.
3. Inside Ladder Instructions Inside Ladder Bottom Bracket The bottom ladder section may need to be cut off if the length is too long. Cut the bottom section at least 12" from the bottom of the floor. Attach the bottom inside ladder brackets (LDR-5133) to the last ladder section using the six (6) holes per ladder rail. You may need to drill out the holes in the last ladder section with a 3/8" drill bit.
4. Warranty GSI Group, LLC Limited Warranty The GSI Group, LLC (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier.
This equipment shall be installed in accordance with the current installation codes and applicable regulations, which should be carefully followed in all cases. Authorities having jurisdiction should be consulted before installations are made. GSI Group 1004 E. Illinois St. Assumption, IL 62510-0020 Phone: 1-217-226-4421 Fax: 1-217-226-4420 www.gsiag.
