User's Manual

MSP Modular Divider Valves
Page 10
L10102
Notes
Right/Left Hand determined when 1.
viewing front of divider valve
assembly. (Divider valve assembly
placed on fl at surface with inlet at
top.)
Valves are specifi ed starting from 2.
inlet section.
When valve is crossported, its outlet 3.
is plugged and output is diverted to
next valve away from inlet.
Last valve in divider assembly, 4.
farthest from inlet, cannot be
crossported.
Single valve can be crossported on 5.
one side only.
When valve is a single, only one 6.
outlet in its subplate can be used,
other outlet must be plugged.
Cycle pins are available on MS (20, 7.
25, 30, 35, and 40) valves only.
All divider valve assemblies must 8.
have a minimum of 3 working
valves.
Bypass block cannot be supplied 9.
on divider valve with 3 subplates.
Bypass block is not a working valve.
Divider systems should be limited to 10.
fi rst and second stages only. Third
staging is not recommended. Refer
to Trabon Bulletins L20101, L20105
and L20115 for further information
on system design.
BY P
Caution
XXX - XXX - XX - X - X - XX - X - XX
SERIES OF FEEDER
MSP - STANDARD INDUSTRIAL TO 3500 PSI
MSV - SYNTHETIC INDUSTRIAL TO 3500 PSI
(VITON SEALS)
INLET/OUTLET PORT TYPES
SAE - STRAIGHT THREAD O-Ring SEAL
NPT - NPSF PIPE THREAD
BPS - BRITISH PARALLEL PIPE O-Ring SEAL (LSO 1179)
MET - METRIC THREAD O-Ring (ISO 6149)
INLET SECTION OPTIONS
MS - MS DIVIDER INLET
MH - MS DIVIDER INLET W/BLEED SCREWS
SH - MS DIVIDER W/SHUNT/SHUT-OFF (115 VAC)
SD - MS DIVIDER W/SHUNT/SHUT-OFF (24 VDC)
ZL - ZERO LEAK SHUT-OF (115 VAC)
ZF - ZERO LEAK SHUT-OFF (24 VDC)
DIVIDER VALVE ACCESSORY OPTIONS
P - ASSEMBLY OF PERFORMANCE INDICATORS IN ALL WORKING OUTLETS
B - ASSEMBLY OF PERFORMANCE INDICATORS AND CHECK VALVES IN ALL
WORKING OUTLETS
C - EXTERNAL CHECK VALVES IN ALL WORKING OUTLETS
E - SPP END SECTION W/PLUG IN 1/8-27 NPSF PORT FOR MANUAL LUBE FITTING -
563279 - (510-770-332)
NUMBER OF SECTIONS
3 - THREE 6 - SIX
4 - FOUR 7 - SEVEN
5 - FIVE 8 - EIGHT
VALVE CAPACITY MS VALVE BLOCK
BP - BYPASS
05 - .005 cu.in. (.082 cm
3
)
10 - .010 cu.in. (.164 cm
3
)
15 - .015 cu.in. (.246 cm
3
)
20 - .020 cu.in. (.328 cm
3
)
25 - .025 cu.in. (.410 cm
3
)
30 - .030 cu.in. (492 cm
3
)
35 - .035 cu.in. (.574 cm
3
)
40 - .040 cu.in. (.656 cm
3
)
TYPE OF VALVE BLOCK
T - TWIN VALVE
S - SINGLE VALVE - RH OUTLET
L - SINGLE VALVE - LH OUTLET
B - TWIN VALE W/CYCLE PIN RIGHT
C - SINGLE VALVE W/CYCLE PIN RIGHT - RH OUTLET
D - SINGLE VALVE W/CYCLE PIN RIGHT - LH OUTLET
H - TWIN VALVE W/CYCLE PIN LEFT
J - SINGLE VALVE W/CYCLE PIN LEFT - RH OUTLET
K - SINGLE VALVE W/CYCLE PIN LEFT - LH OUTLET
CROSSPORTING OPTION
CR - RIGHT HAND SIDE
CL - LEFT HAND SIDE
CB - BOTH SIDES
Ordering Example
5-section MSP Divider Valve Assembly, standard seals, SAE ports and
performance indicators in each working outlet. Consisting of:
1 - .030 Twin Valve with Cycle Pin Right Side
1 - .040 Single Valve - Crossport Right Side
1 - .040 Single Valve - Right Hand Outlet
1 - .020 Twin Valve
1 - Bypass Block
Ordering Code - MSP-SAE-MS-P-5-30B-40SCR-40S-20T-BP
How to Order
Ordering Information