manual

See images -
See images -
See images -
See images -
See images -
See images -
See images -
See images -
See images -
15
14
3
13
16
34
32
36
39
62
66
1
8
14
33
31
35
37
60
65
Instructions
Vibration Assembly and Seat Wire
Attaching Tray
Squeeze recline handle on seat and lower
seat before attaching tray.
Line up tray on edge of seat and insert peg
into hole and close tray.
See image
See image
4
5
6
7
Installing Batteries
With baby out of swing, open the battery
compartment lid by inserting a screwdriver into
the coin slot. Insert three “D”-LR20 (1.5V) cell
batteries.
CHECK that the batteries are put in correctly.
Your swing will not run if the batteries are put
in backwards.
48
49
GB
Attaching Bouncer Legs
Attaching Seat Pad
Rear Tube
Assembling Toy Bar
Hanger Tubes
Attaching Carrier
Adjust Recline (3 positions)
Attaching Rear Legs
See image
- Insert rear legs into holes in housings as shown.
Button MUST snap through hole.
17
18
See images -
Use slide adjuster at shoulder and waist for further
adjustment. Repeat on other side.
When changing harness strap slots, MAKE SURE
harness straps are going through same slots in seat
pad.
The harness straps must go into the slot that is
even with or slightly above the shoulders.
Avoid twisting straps.
45
46
47
To Secure Child
40 44
Starting Product
WARNING: avoid serious injury from falling or sliding
out. Always use harness. After fastening buckles, adjust
belts to get a snug fit around your child.
TO TURN PRODUCT ON:Press On /Off button or
press any speed from 1 to 6. When pressing On/Off
button, it automatically starts with the last speed setting
that was selected before the product was turned off.
Observe the swinging motion for a minute. It takes
time for the product to adjust to a setting. Change
setting if needed.
A small, quiet baby will swing higher on each setting
than a larger, more active baby.
Head Support
For Storage
Mix ‘N Move
Vibration
Push buttons to fold.
63
Only use this head support on this swing.
Never use this head support on any other product.
59
See images -
See images -
63
58
64
59
19
Attaching Front Legs
See image
The double buttons must fit into the channels inside
the battery housing.
Button MUST snap through hole.
Swing the leg outward until the single button snaps
its notch. CHECK that the leg is properly attached
by twisting it in the housing.
20
21
22
Repeat step 13 with other housing and leg.
Button MUST snap through hole.
Swing the leg outward until the single button snaps
its notch. CHECK that the leg is properly attached
by twisting it in the housing.
23
24
TIMER— Push “Timer” button to set the timer for
the swing and/or Music/Nature sounds. If the timer
button is not pushed, the swing and/or music/
nature sound will continue to play until the power
on/off button is pushed or the music/nature off
button is pushed.
When using the timer with the product on, if the
button is pushed once, the red speed light will
flash once and timer is set for 10 minutes. Pushing
the timer button a second time will increase the
run time to 20 minutes and the red speed light
will flash twice.
Pushing a third time will increase the time to 30
minutes and the red speed light will flash three
times.
When using the timer with the Music/Nature
sounds on, the timer will set to 10, 20 or 30
minutes as described for the swing, but there
will be no flashing light.
57
Button Functions
SPEED – Press On /Off button or press any speed
from 1 to 6. When pressing On/Off button, it
automatically starts with the last speed setting that
was selected before the swing was turned off.
ON/OFF POWER - Press to turn ON and turn
OFF. Press button to stop swing motion.
MUSIC - Push “Music” button to turn on music.
Push button again to advance to next track. There
are 10 songs.
MUSIC/NATURE OFF - Press button to turn OFF.
VOLUME— Press the plus (+) to raise the volume
and the minus (-) to lower the volume. There are
5 volume settings.
NATURE SOUNDS— Push “Nature” button to
turn on nature sound selection. Each press will
change to the next nature sound. After the 5th
sound is selected, it will return to the first track.
51
52
53
54
55
56
Your seat may be stopped at any time the motor is
running without damaging the motor. Push product to
restart.
If your product motor stops operating by itself, a
protective device may have been activated. Turn off
motor, wait three minutes, then restart swing.
TO TURN PRODUCT OFF: Press On /Off button.
See images -
27
25
Front Tube
Attaching Front Tube to Legs
See image
CHECK that all tubes are securely attached.
CHECK that the parts of the frame are assembled
in the positions shown.
See image
28
29
30
50