Failure to follow these warnings and the assembly instructions could result in serious injury or death. Stroller OWNERS MANUAL Model No. Serial No. Dear Customer, Please fill in the model and serial numbers above from the label on the rear leg of your new stroller. Never leave child unattended. Always keep your child in view. Avoid serious injury from falling or sliding out. Always use seat belt. Never place child in the stroller with head toward front of the stroller.
Failure to follow these warnings and the assembly instructions could result in serious injury or death. Stroller OWNERS MANUAL Model No. Serial No. Dear Customer, Please fill in the model and serial numbers above from the label on the rear leg of your new stroller. Never leave child unattended. Always keep your child in view. Avoid serious injury from falling or sliding out. Always use seat belt. Never place child in the stroller with head toward front of the stroller.
PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your stroller. If any parts are missing, call Customer Service at 1-800-345-4109 or visit our Internet website, www.gracobaby.com. THIS PRODUCT REQUIRES ADULT ASSEMBLY. Step 4. Step 1. Pull firmly on each axle mount to be sure it is securely attached. Flatten stroller carton to protect floor. Step 2. If the axle mounts do not snap on the legs, they may be facing the wrong way.
PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your stroller. If any parts are missing, call Customer Service at 1-800-345-4109 or visit our Internet website, www.gracobaby.com. THIS PRODUCT REQUIRES ADULT ASSEMBLY. Step 4. Step 1. Pull firmly on each axle mount to be sure it is securely attached. Flatten stroller carton to protect floor. Step 2. If the axle mounts do not snap on the legs, they may be facing the wrong way.
To Unfold Stroller To Secure Your Child To Fold Stroller Step 1. Avoid serious injury from falling or sliding out. Always use seat belt. Before folding the stroller: 1. Fold the canopy. 2. Lock the front swivels (on certain models). Release storage latch located by the stroller handle and begin opening stroller. Storage latch Step 2. Continue unfolding until both latches lock. Your stroller may have a single button buckle, double button buckle, or two-buckle seat belt.
To Unfold Stroller To Secure Your Child To Fold Stroller Step 1. Avoid serious injury from falling or sliding out. Always use seat belt. Before folding the stroller: 1. Fold the canopy. 2. Lock the front swivels (on certain models). Release storage latch located by the stroller handle and begin opening stroller. Storage latch Step 2. Continue unfolding until both latches lock. Your stroller may have a single button buckle, double button buckle, or two-buckle seat belt.
The following optional features are found only on certain models: To Attach the Graco® Safety Seat* Improper use of this stroller with a carrier may result in serious injury or death. To Use Bottle Holders* Do not use this stroller with carriers or safety seats other than Graco® Travel System models. Two mesh pockets are provided in rear of basket for infant bottle storage. Read the manual provided with your Graco® Travel System Safety Seat before using the Travel System.
The following optional features are found only on certain models: To Attach the Graco® Safety Seat* Improper use of this stroller with a carrier may result in serious injury or death. To Use Bottle Holders* Do not use this stroller with carriers or safety seats other than Graco® Travel System models. Two mesh pockets are provided in rear of basket for infant bottle storage. Read the manual provided with your Graco® Travel System Safety Seat before using the Travel System.
Infant Safety Seat/Carrier OWNER'S MANUAL Even if using this seat seems easy to figure out on your own, it is very important to read this manual. Your child’s safety depends on you installing and using this seat correctly. READ THIS MANUAL! Return this manual to the storage pocket on the back of the safety seat for quick reference.
2 Table of Contents 1. Warnings to Parents and Other Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Registering Your Safety Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 3.1 About Your Child . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Adjusting the Features and Components of the Safety Seat . . . . . . . . . . . . . 21-29 5.1 Features and Components: 3-Point Harness . . . . . . . . . . . . . . . . . . . . . 22-23, 26 5.2 Features and Components: 5-Point Harness . . . . . . . . . . . . . . . . . . . . . . . . . 24-26 5.3 Removing and Attaching the Safety Seat Base. . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.4 Adjusting the Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Our goal is to make every product the best it can be! We are also committed to supporting our products after purchase. If you would like to speak to Graco about your product, please call our Customer Service Department at 1-888-224-6549. Our knowledgeable staff is ready to answer any questions you may have concerning parts, use or maintenance. When you call, please have the model and serial numbers ready so your call may be processed quickly and efficiently.
1. Warnings to Parents and Other Users DO NOT install or use this safety seat until you read and understand the instructions in this manual and in your vehicle owner’s manual. DO NOT let others install or use the safety seat unless they understand how to use it. Failure to properly use this safety seat increases the risk of serious injury or death in a sharp turn, sudden stop or crash. Your child’s safety depends on you installing and using this safety seat correctly. Your child’s safety depends on: 1.
6 2. Registering Your Safety Seat Model No. Serial No. Purchase Date Dear Customer, Please fill in the above information. The model and serial numbers can be found on a label underneath your safety seat. Fill out the prepaid registration postcard attached to the seat pad and mail it today. Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address and serial number to: Graco Children’s Products Inc. P.O.
3. Important Safety Information No safety seat can guarantee protection from injury. However, proper use of this safety seat reduces the risk of serious injury or death to your child. 3.1 About Your Child THIS SAFETY SEAT IS DESIGNED for use only by children who weigh 20 lbs. (9 kg) or less and whose height is 26 inches (66 cm) or less. Using this safety seat with a child who is heavier than 20 lbs. or more than 26 inches in height may increase the risk of serious injury or death.
8 3.2 About Using this Safety Seat in Your Vehicle YOUR CHILD CAN BE INJURED in a vehicle even if you are not in a crash. Common events such as sudden braking and sharp turns can injure your child if the safety seat is not properly installed or if your child is not properly secured in the safety seat. THERE ARE MANY KINDS of vehicles, seat belt systems, and occupant protection systems.
3.3 A Warning About Air Bags NEVER PLACE THIS SAFETY SEAT IN A VEHICLE SEATING LOCATION THAT HAS AN AIR BAG. If an air bag inflates, it can hit the safety seat with great force and cause serious injury or death to your child. Refer to your vehicle owner’s manual for information about air bags and child safety seat installation. 3.4 When the Safety Seat is Not Occupied PARTS OF THE SAFETY SEAT can become very hot if the seat is left in the sun. Contact with these parts can burn your child’s skin.
10 3.5 About the Life and Condition of this Safety Seat REPLACE THE SAFETY SEAT AND BASE after an accident of any kind. An accident can cause damage to the safety seat and base that you cannot see. EVEN IF THE SAFETY SEAT AND BASE are not involved in an accident, stop using both and throw them away six years after the date of manufacture. The date of manufacture can be found on the serial label located on the underside of the safety seat or base.
3.6 Warnings About Using the Safety Seat as a Carrier FALL HAZARD: Child’s movements can slide carrier. Never place carrier near edges of counter tops, tables or other high surfaces. Always stay within arms reach whenever carrier is not on floor/ground. Be sure handle locks into position before lifting carrier. SUFFOCATION HAZARD: Infant Carrier can roll over on soft surfaces and suffocate child. Never place carrier on beds, sofas or other soft surfaces.
12 NEVER PLACE carrier in the top of a shopping cart. Strings and cords can cause strangulation. Keep strings and cords away from child: DO NOT place carrier near a window where cords from blinds or drapes can strangle a child. DO NOT hang strings on or over the carrier. DO NOT place items with a string around a child’s neck, such as hood strings, pacifier cords, etc. DO NOT attach strings to toys.
4. Selecting a Suitable Location for the Safety Seat Some seating positions in your vehicle may not be safe locations for this safety seat. In fact, some vehicles do not have any seating positions that can be used safely. Improper placement of the safety seat increases the risk of serious injury or death. Follow the instructions in this section and in your vehicle owner’s manual to select a location for the safety seat.
14 We recommend that, whenever possible, you secure the safety seat in the center position of the seat directly behind the front seats Ê. We also recommend that an adult ride in the rear seat to watch the child. If the driver is the only adult present, a child who must be closely watched may need to ride in the front seat, but should only do so if there is no passenger-side air bag and all of the other vehicle seat and seat belt requirements listed below are met. Ê 4.
THE VEHICLE SEAT MUST FACE FORWARD. DO NOT place safety seat in a rear-facing vehicle seat Ì or a side-facing vehicle seat Í. ONLY use this safety seat on vehicle seats with seat backs that lock in an upright position. Do not use seats that can fold down without having to release a lock or latch of some kind. These seats can fly forward and strike the child in a sudden stop or crash.
16 4.3 Be Sure Your Vehicle Seat Belt is Safe to Use The vehicle seat belt must be designed to hold the safety seat tightly at ALL times. There are a variety of seat belt systems that are NOT safe for use with the safety seat because they will not hold the safety seat tightly at all times. We will first describe the seat belts that are not safe for use and then we will describe those that are safe for use.
A. Seat Belt Systems that are NOT Safe for Use with the Safety Seat DO NOT use the following types of vehicle belt systems with your safety seat. They will not hold the safety seat securely in place. The metal locking clip provided with this product will NOT make any of these seat belts safe. DO NOT use a lap belt that stays loose and can move until it locks in a crash or sudden stop Ê. This belt has an Emergency Locking Retractor, E.L.R. It is often seen in combination with a motorized shoulder belt.
18 DO NOT use a seat belt that is attached to the door in any way Ê. This type of belt is designed to open with the door and automatically surround the passenger when the door is closed. This seat belt will NOT safely restrain the safety seat. DO NOT use a seat belt that is anchored forward of the seat crease Ë. This seat belt will NOT safely restrain the safety seat. DO NOT use a shoulder belt that moves along a track to automatically surround the passenger when the door is closed Ì.
B. Seat Belt Systems that are Suitable for Use with the Safety Seat The following vehicle belt systems can be used with your safety seat, IF the seat location meets all other requirements of these instructions AND THOSE IN YOUR VEHICLE OWNER’S MANUAL. Lap belt that is manually adjusted and stays tight Í. This type of seat belt is tightened by Í Lap belt that cannot lengthen once it is buckled Î. This belt has an automatic locking retractor (A.L.R.
20 Lap/shoulder combination belt with a locking latchplate Ê. Once it is buckled, this type of belt has a latchplate that will not allow the lap portion of the belt to loosen. This seat belt does not require a locking clip. Ê Ë Lap/shoulder combination belt with a latchplate that can slide freely along the belt Ë. This type of belt MUST be converted to prevent movement of the lap portion of the belt.
5. Adjusting the Features and Components of the Safety Seat Each model of the safety seat comes with different harness and base options. Please follow the instructions that are appropriate for the model you have purchased. Your seat will have either a 3-point or a 5-point harness. 3-point 5-point Your base will be either adjustable or non-adjustable. To adjust your safety seat properly, it is very important that you follow the instructions for the model you have purchased.
22 5.
Canopy Harness tightener Release handle Locking clip Level indicator Harness anchor buckle Harness slot Mounting notch Owner’s manual pocket Attachment latch Rear View: 3-Point Harness 23
24 5.
Canopy Release handle Mounting notch Locking clip Level indicator Harness slot Owner’s manual pocket Attachment latch Metal junction plate Waist strap anchor buckle Harness adjustment strap Rear View: 5-Point Harness 25
26 Non-adjustable Base Adjustable Base Recline adjustment knob Vehicle belt path Recline adjustment foot Vehicle belt path Level Indicator The level indicator is attached to the side of the safety seat, and indicates whether or not the safety seat is properly reclined. Locking Clip The locking clip is stored on the back of the safety seat. You will need to use it with certain types of vehicle seat belts.
5.3 Removing and Attaching the Safety Seat Base 1. Squeeze base release handle at back of the safety seat to release the attachment latch. Lift safety seat from base as shown Ê. 2. To reattach seat, push it down until the safety seat clicks into base. 3. Pull up on safety seat to be sure it is latched firmly into base. Ê 5.4 Adjusting the Handle The handle can lock into any of three positions for carrying, reclining, or sitting. To adjust the handle: 1.
28 3. Release buttons and rotate handle until it clicks into desired position and both handle adjustment buttons pop out Ê. 4. Push on the handle to be sure it is locked firmly in position. Ê Carrying Reclining Sitting 5.5 Attaching the Canopy The fabric canopy comes disassembled with four identical plastic supports. The supports are straight at one end and are shaped like a “C” at the other end. To assemble and attach the canopy to the safety seat: 1.
2. Slide straight end of another support into the straight end of the support which has been pushed through the canopy Ì. 3. Using remaining supports, repeat steps 1 and 2 for the other canopy tunnel. The canopy will look like the picture Í. 4. On each side of the safety seat, locate the round ridged areas between the safety seat and the base of the handle. Attach “C” ends of canopy supports to the round ridged areas Î.
30 6. Inserting the Harness Straps in the Proper Slots Failure to properly adjust the harness straps for your child increases the risk of serious injury or death in the event of a sharp turn, sudden stop or crash. The harness straps must be properly adjusted to fit your child according to the following instructions. The harness straps must go into the harness slots that are even with or just below your child’s shoulders. To properly adjust the harness to your child: 1.
Ê 2. Place your child in the safety seat so your child’s bottom rests against the back of the safety seat. See diagram 2 on page 38. Determine which pair of harness slots are even with or just below your child’s shoulders Ê. DO NOT use the upper harness slots if they are above your child’s shoulders. They will not hold a small child securely in a sharp turn, sudden stop or crash. Use harness slots even with or just below child’s shoulders 3.
32 Models with 3-Point Harness 1. From the back of the safety seat, push a corner of the harness anchor buckle back into its harness slot. From the front of the safety seat, use the harness strap to pull the buckle through the slot Ê. Harness anchor buckle Ê Harness tightener 2. Insert the harness anchor buckle all the way through the appropriate slot as determined in step 2 on page 31 Ë. 3. From the back of the safety seat, loosen and remove the other harness strap from the harness tightener.
4. Insert the harness strap through the appropriate slot. Thread the harness strap through the tightener exactly as shown in the picture Ì. Ì 5. Inspect the harness straps from the front and back of the safety seat to be sure they are not twisted. Twisted belts can create slack in the harness straps and reduce the protection provided by the safety seat. Í 6. Pull on the harness straps from the front of the safety seat to be sure the straps are secure.
34 Models with 5-Point Harness 1. Locate the harness adjustment button under the seat flap. Depress the harness adjustment button and pull the shoulder straps out to loosen the harness Ê. 2. Behind the seat, pull the adjustment strap down until the metal junction plate is below the owner’s manual pocket. Remove the ends of the two shoulder straps from the metal junction plate Ë. From the front of the seat, pull the straps through the harness slots.
Ì For a smaller baby: Use the lower harness slots (if they are even with or just below your child’s shoulders) and the upper strap loops Ì. The ends of the straps must hang in front of the metal plate as shown in Ì, not in Í. Í Lift up the strap ends to check that the loops are completely within the junction plate slots Î and pull on the straps to be sure the straps are secure.
36 For a larger baby: Use the upper harness slots and the end strap loops Ê. Check that the loops are completely within the junction plate slots and pull on the straps to be sure the straps are secure. Ê 4. Inspect the harness straps from the front and back of the safety seat to be sure they are not twisted. Twisted belts can create slack in the harness straps and reduce the protection provided by the safety seat. 5.
7. Securing Your Child in the Safety Seat/Carrier Failure to properly secure your child in the safety seat/carrier increases the risk of serious injury or death from suffocation or falls, or in the event of a sharp turn, sudden stop or crash. In a crash, the safety seat provides NO protection for your child unless the harness straps are properly secured. Even when used only as a carrier, make sure the harness straps are properly secured. Follow these instructions carefully to properly secure your child. 1.
38 3. Move the safety seat handle to the sitting position (see page 27) and remove the strap from the harness clip as shown Ê. Unbuckle the harness and drape the harness straps over the back or sides of the safety seat. Ê OR 3-Point Strap removed from harness clip 4. Place your child in the safety seat so that the child’s bottom rests against the back of the safety seat Ë. 5. Pull the harness straps down over your child.
Models with 3-Point Harness 6. Buckle the harness to the latch between your child’s legs. Make sure that you hear a “click.” If the harness straps are not buckled, the safety seat provides NO protection for your child. DO NOT use the safety seat if the harness does not latch in place. Call Graco at 1-888-224-6549. 7. From the back of the safety seat, pull the strap through the harness tightener to tighten the straps as shown Ì. Make sure that both straps are flat and tight on your child’s shoulders. 8.
40 Models with 5-Point Harness 6. Insert the two buckle tongues into the harness buckle on the crotch strap. Make sure that you hear each tongue click into the buckle. If the harness straps are not buckled, the safety seat provides NO protection for your child. DO NOT use the safety seat if the harness does not latch in place. Call Graco at 1-888-224-6549. 7. Slide the strap back into the harness clip Ê. This is easier to do when the harness clip is near the buckle. 8.
Models with Either Harness Style 11. Some infants may need extra support to keep their head and body in a comfortable position. Your model may include a head support cushion. To use the cushion, unsnap the sides and resnap them with the harness straps threaded through the slots in the cushion Í. If your model does not include a head support, you may want to use a rolled towel or a blanket. BUT MAKE SURE THAT THESE OBJECTS DO NOT INTERFERE WITH THE HARNESS Î.
42 8. Securing the Safety Seat/Base in Your Vehicle There are many kinds of vehicles, seat belts, and occupant protection systems. As a result, it is not possible for this manual to tell you everything you need to know about putting this safety seat in your vehicle. You must carefully follow the instructions provided by your vehicle manufacturer, in addition to the information in this manual. Before proceeding, be sure you have read and understood section 4.
Preparation and Initial Safety Checks Ê 1. Make sure vehicle is on level ground so that the level indicator, which is attached to the safety seat, can be used to properly recline the safety seat Ê. 2. Make sure you have selected a suitable location for the safety seat as explained in section 4, “Selecting a Suitable Location for the Safety Seat” (page 13). 3. Check again to be sure that the vehicle seat does not have an air bag, and that an adjacent seat’s air bag will not strike the safety seat. 4.
44 Positioning and Securing the Safety Seat/Base 6. Remove safety seat from base, regardless of whether or not you plan on using the base. Squeeze the base release handle at the back of the safety seat and lift the safety seat from the base. 7. If you are going to use the base, place the base in a rear-facing position in a forward-facing vehicle seat Ê. If you are not using the base, place the safety seat in a rear-facing position in a forward-facing vehicle seat Ë.
8. Thread the seat belt: a. If you are using the base, follow diagram Ì. b. If you are not using the base, follow diagram Í. Ì 9. Buckle the seat belt. Make sure the buckle tongue goes into the correct buckle, and not the adjacent one Î. The seat belt should not be twisted or turned.
46 10. Now the vehicle seat belt must be tightened. When tightening the seat belt over the safety seat, make sure there is no slack on either side of the safety seat or between the vehicle belt hooks on the safety seat. When tightening the seat belt through the base, make sure there is no slack on either side of the base or along the base belt path.
11. Tightening a lap-only belt: An automatically adjusted lap belt Ë is tightened by feeding the seat belt back into its retractor while pushing down hard on the safety seat or base. Make sure that seat belt is locked in place and very tight. A manually adjusted lap belt Ì is tightened by pulling on the excess belt while pushing down hard on the safety seat or base. However, you may have trouble tightening the belt because of the upright angle at which you must pull.
48 belt because of the upright angle at which you must pull. You may have to unbuckle the seat belt, estimate a seat belt length that will make the seat belt very tight, then buckle it again. A lap/shoulder combination belt with a latchplate that can slide freely along the belt Ê requires the locking clip, unless your vehicle’s seat belt can be converted in another way that is described in your vehicle owner’s manual.
Ì d. Connect the lap belt to the shoulder belt by placing the locking clip on the belts about ½ inch from the latchplate as shown Ë and Ì. e. Re-buckle the belt and pull hard on the lap belt to be sure it does not move. f. Repeat this procedure if the lap belt is loose or lengthens when pulled. Locking clip goes here, /2 inch from the buckle 1 13. If you are using the base, make sure that there is nothing on top of or in the base that may interfere with attachment of the safety seat.
50 Properly Reclining the Safety Seat/Base For your child’s safety, it is important that your safety seat/base be properly reclined. Attached to the side of your safety seat is a level indicator to help properly recline the safety seat/base on the vehicle seat. Failure to properly recline the safety seat on the vehicle seat increases the risk of serious injury or death. If the safety seat is too upright, a child’s head may drop forward and cause breathing problems.
Adjustable Base: 14. Make sure the safety seat/base is not tilted sideways on the vehicle seat. Check the level indicator. You must look straight on at the indicator. If the indicator shows ONLY blue, the safety seat is properly leveled. If any orange is showing in the level indicator, the safety seat is either too upright or too reclined.
52 Non-adjustable Base: 14. Make sure the safety seat/base is not tilted sideways on the vehicle seat. Check the level indicator. You must look straight on at the indicator. If the indicator shows ONLY blue, the safety seat is properly leveled. If any orange is showing in the level indicator, the safety seat/base is either too upright or too reclined. If the safety seat/base is too upright, place rolled towels as shown until indicator shows ONLY blue Ê.
Without Base: 14. Make sure the safety seat is not tilted sideways on the vehicle seat. Check the level indicator. You must look straight on at the indicator. If the indicator shows ONLY blue, the safety seat is properly leveled. If any orange is showing in the level indicator, the safety seat is either too upright or too reclined. If the safety seat is too upright, place rolled towels as shown until indicator shows ONLY blue Ì.
54 Final Safety Checks 15. If your child is already in the safety seat because you have been using it as a carrier, make sure child is secured with the harness according to section 7, “Securing Your Child in the Safety Seat/Carrier” (page 37). 16.
If you find that your safety seat moves or your vehicle seat belt slips or becomes loose, make sure you have followed steps 1-15 correctly, or see section 4, “Selecting a Suitable Location for the Safety Seat” (page 13). DO NOT USE THIS SEATING LOCATION IF THE SEAT BELT DOES NOT HOLD THE SAFETY SEAT TIGHTLY. 9. Using the Safety Seat in an Airplane This safety seat may be installed in an airplane the same way that it is installed in an automobile.
56 10. Using the Safety Seat with a Graco® Stroller This safety seat can be used with certain models of Graco® LiteRider strollers. Refer to your LiteRider instruction sheet for details about how to attach the safety seat to your stroller. If you do not have an instruction sheet, please call toll-free, 1-888-224-6549 to obtain one, or visit our website, www.gracobaby.com. 11. Cleaning and Maintenance TO REMOVE AND WASH SAFETY SEAT PAD, see following pages.
Models with 3-Point Harness To wash the safety seat pad: Harness anchor buckle 1. From the back of the safety seat, loosen and remove the harness strap from the harness tightener. From the front of the safety seat, pull the harness strap through the slot. 2. From the back of the safety seat, push a corner of the harness anchor buckle back into its harness slot Ê. From the front of the safety Harness seat, use the harness strap to pull the buckle tightener through the slot. 3. Carefully remove the seat pad.
58 Models with 5-Point Harness To wash the safety seat pad: 1. Detach the harness shoulder straps from the junction plate by following the instructions on page 34. 2. Below the owner’s manual pocket, to the left and right, are small anchor buckles attached to the waist straps of the harness. Push aside the small tab that holds the anchor buckles in place Ê and pull the anchor buckles out of their indentations. Push a corner of each anchor buckle back into its slot Ë. 3.
4. Carefully remove the seat pad. DO NOT USE SAFETY SEAT without the seat pad. 5. Machine wash on delicate cycle and drip-dry. DO NOT USE BLEACH. 6. Fit pad into position, then reverse the process above to properly reinstall the harness system. You must: a. Pass the shoulder straps through the appropriate slots and under the owner’s manual pocket, b. Secure the shoulder straps to the metal junction plate, and c.
60 12. Replacement Parts Ordering Safety Seat Parts Complete the form that follows. Your safety seat model and serial numbers MUST be included on the form to ensure proper replacement parts. The numbers can be found on a sticker on the underside of your safety seat. Payment must accompany your order. Parts List: Price:** Seat pad ................................. $ 20.00 Canopy ................................... $ 17.00 Canopy bow ........................... $ 5.00 3-point harness* ....................
Model No. Serial No. Account #: (Both numbers required) Seat pad Canopy Canopy bow 3-point harness 5-point harness Harness clip Locking clip Head support Adjustable base Charge to credit card: Visa MasterCard Discover Expiration date: Signature: Check enclosed (payable to Graco Children’s Products Inc.) SHIP TO: Name Subtotal: Shipping & handling*: $5.00 Address 6% sales tax (PA only): City, State, Zip Total: ( ) Telephone *$15.00 outside the continental U.S.
Graco Children’s Products Inc.