Instructions-Parts Alternator Conversion Kit 313293C EN For converting an XM plural-component sprayer wall power supply to a turbine power supply. For professional use only. Not for use in explosive atmospheres. Part No. 256991 Important Safety Instructions Read all warnings and instructions in the XM Plural-Component Sprayer Operation manual. Save these instructions. For patent information, see www.graco.
Related Manuals Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Component Identification . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Remove Power Supply . . . . . . . . . . . . . . . . . . . . 4 Install Alternator . . . . . . . . . . . . . . . . . . . . . . . . . 5 Install Regulator Assembly . . . . . . . . . . . . . . . . . 5 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Identification Component Identification Power Supply Cable Connections Alternator Conversion Kit Cable Connections D D G E J B J F 3 C A B C H r_256991_313293_10 4 r_256991_313293_9 FIG.
Installation Installation 6. Disconnect CAN cable (H) from USB front CAN connector and display module (C). See FIG. 1 on page 3. It is required to remove the power supply before installing the alternator conversion kit. Always have a qualified electrician perform wiring connections. NOTE: Cable (H) will not be used for alternator conversion kit. 7. Disconnect CAN cable (J) from USB module and fluid control module. Do not discard cable (J). CAN cable (J) will be used by alternator conversion kit.
Installation Install Alternator Install Regulator Assembly 1. Use screws (14) to install alternator (1) inside junction box (JB). 1. Position regulator (6) for proper air flow direction. L JB 13 5 12 1 6 ai r 9 10 f lo w K 7 r_256991_313293_1 FIG. 5: Install Regulator Assembly 14 FIG. 3: Install Alternator r_256991_313293_12a 2. Install screw (14) through other end of grounding wire (17), washer (19), and mounting hole beneath the grounding label inside junction box (JB). 2.
Setup Setup Connect Hose Connect Cables 1. Connect tubing (15) between the air regulator outlet fitting (10) and the alternator air inlet (M). Use reference labels located near CAN connectors to properly connect components that are connected with the alternator. Each CAN cable is marked with the part number. The ends with the blue-colored sockets attach to the alternator. See FIG. 1 on page 3 for Alternator Conversion Kit Cable Connections. 1.
Parts Parts 256991, Alternator Conversion Kit 14 1 19 14 18 12 6 5 17 13 10 14 r_256991_313293_11 7 9 Ref. 1 3† 4† 5 6 7 9 10 12 13 14 15† 16† Part Description Qty. 255728 MODULE, alternator 1 15V782 CABLE, I.S. CAN, male/ female, 20 1 in. 15V783 CABLE, male A to female B code, 1 39 in.
Technical Data Technical Data Alternator Module Maximum Air Working Pressure Minimum Air Working Pressure 8 19 psi (1.13 MPa, 1.31 bar) 17 psi (0.13 MPa, 0.
Technical Data 313293C 9
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
