Instructions - Parts Electric Heated Hose Power Supply Kit 256876 313258C EN Monitor and control fluid temperature in a low voltage heated hose for XM plural-component sprayers feeding a remote XM mix manifold. Not for use in explosive atmospheres. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 2 for a list of components included in the kit and maximum working pressures.
Related Manuals Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connect Power Cable Wires . . . . . . . . . . . . . . . . 5 Connect 24M943 FTS and Power Wires . . .
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode.
Warnings WARNING WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point gun at anyone or at any part of the body. • Do not put your hand over the spray tip. • Do not stop or deflect leaks with your hand, body, glove, or rag. • Do not spray without tip guard and trigger guard installed.
Installation Installation Setup 1. Insert rubber feet of control box through holes in plate (4). Mount control box (2) on the XM frame using plate (4), bolts (7), and nuts (6). Installing this equipment requires access to parts that may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician connect power and ground to power switch terminals; see manual 3A2980 and FIG. 4 on page 6.
Setup 5. Route power cable (3) up through cord grip (JC). 7. Connect power wiring from 1L1 and 3L2 to terminal blocks 1 and 3 in TB1. 6. Connect other end of grounding wire to grounding lug nut (X) inside junction box (J). TB1 J X C JC 3 D 3L2 3L2 1L1 C 2 PE ti20975a FIG.
Setup 8. Set transformer wire taps in hose heat control box (2). See manual 3A2980 to verify tap wire connection. Connect 24M943 FTS and Power Wires 9. Install adapters (16) in dosing valve blocks and use fittings (14, 15, 17, or 18) to connect heated hose (1) fluid inlets. NOTICE Do not coil hose tighter than the minimum bend radius of 3 ft (0.9 m). Do not subject hose to excessive weight, impact, or other abuse. 1. Carefully extend FTS probe (H) into the hose section from the hose heat control.
Troubleshooting/Repair Troubleshooting/Repair See supplied hose heat control manual 3A2980 and power-lock heated hose manual 309572 for troubleshooting and repair procedures.
Parts Parts 6 2 8 5 16 6 14, 15, 17, or 18 14, 15, 17, or 18 7 23 12 7 9a 6 9 4 12 WL E Ref.
GND 1ph 230V 6T3 5L3 S1 2T1 4T2 1L1 3L2 40A DISCONNECT 16 PE 19 L1 GND-3 L2 86 20A FILTER 1100 1050 9 3 CB1 20A 4 CIRCUIT BREAKER 1 2 1101 1051 41 FAN 45 JUMPER TB1 TB4 38 JUMPER 1101-1 1051-1 3 TB2 TB5 1071 4 4 1101-3 TB3 1101-2 1051-3 1051-2 POTENTIOMETER 2 1 3 A2 PROPORTIONAL CONTROLLER 14 26 1051-4 1101-4 1051-5 OS1 INDICATOR 43 2A FUSE 250V F1 11 VR1 1052 1072 4 5 6 7 1053 1 1 11 1161 TEMP CONTROLLER A1 1 2 3 4 T1 1102 12 1162 1191
Technical Data Technical Data Hose Heat Control 24P616 Input Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . 230 Vac, 1 phase, 50/60 Hz, 15A Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-62 Vac, 45 A Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 lb (39 kg) Heated Hose 248908, 248907, 262727, 262728, 262730 Maximum working fluid pressure . . . . . . . . . . . . . . . . . . . 5000 psi (34.
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
