Instructions - Parts List 311075U EN For spraying or dispensing 1:1 mix ratio materials, including epoxies, polyurethane foam, polyurea coatings, and joint fill materials. For professional use only. Not approved for use in European explosive atmosphere locations. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 4 for a list of models and maximum working pressures.
Contents Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Isocyanate Hazard . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Foam Self-ignition . . . . . . . . . . . . . .
Related Manuals Related Manuals The following manuals are for Reactor E-10 components and accessories. Some are supplied with your package, depending on its configuration. Manuals are also available at www.graco.com. 68 Fusion Mechanical Purge Spray Gun Displacement Pump Part No. Description 311076 Instruction-Parts Manual (English) Fluid Heater Part No. Description 311210 Instruction-Parts Manual (English) Fusion Air Purge Spray Gun Part No.
Models Models The model no., series letter, and serial no. are located on the back of the Reactor E-10. For faster assistance, please have that information ready before calling Customer Service.
Warnings Warnings The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual, refer back to these pages for a description of the specific hazard.
Warnings WARNING SKIN INJECTION HAZARD High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Engage trigger lock when not spraying. • Do not point gun at anyone or at any part of the body. • Do not put your hand over the spray tip. • Do not stop or deflect leaks with your hand, body, glove, or rag.
Warnings WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • This equipment is for professional use only. • Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure in this manual when equipment is not in use. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.
Overview Overview The Reactor E-10 is a portable, electric-powered, 1:1 mix ratio proportioner, for use with a wide variety of coatings, foams, sealants, and adhesives. Materials must be self-leveling and pourable, and may be applied with impingement mix spray guns, disposable mixer guns, or flush-type mix manifolds. Reactor E-10 is gravity-fed from 7 gal. (26.5 liter) supply tanks mounted on the unit. The tanks are translucent to allow monitoring of fluid level.
Isocyanate Hazard Isocyanate Hazard form small, hard, abrasive crystals, which become suspended in the fluid. Eventually a film will form on the surface and the ISO will begin to gel, increasing in viscosity. If used, this partially cured ISO will reduce performance and the life of all wetted parts. Spraying materials containing isocyanates creates potentially harmful mists, vapors, and atomized particulates.
Keep Components A and B Separate Keep Components A and B Separate NOTICE To prevent cross-contamination of the equipment’s wetted parts, never interchange component A (isocyanate) and component B (resin) parts. Changing Materials • When changing materials, flush the equipment multiple times to ensure it is thoroughly clean. • Always clean the fluid inlet strainers after flushing, see page 28. • Check with your material manufacturer for chemical compatibility.
Component Identification Component Identification Key for FIG. 1 A B C D E F G H J K L Supply Tank A Supply Tank B Pump A Pump B Heater A Heater B Fluid Pressure Gauges Recirc/Spray and Overpressure Relief Valves Control Panel; see FIG.
Component Identification Key for FIG. 2 A B C D G H J K L M Supply Tank A Supply Tank B Pump A Pump B Fluid Pressure Gauges Recirc/Spray and Overpressure Relief Valves Control Panel; see FIG.
Controls and Indicators Controls and Indicators ST MP CF HP TD TD TI7016a FIG. 3. Controls and Indicators (heated unit shown) Motor/Pump Control Function Knob • Use knob (CF) to select desired function. Icon Setting Function Stops motor and automatically parks pumps. Slow Slow recirculation Recirc speed. Fast Recirc Fast recirculation speed. Pressure Adjusts fluid pressure Adjust to gun in spray mode.
Controls and Indicators Motor Power Switch/Circuit Breaker Heater Temperature Controls Switch (MP) turns power on to control board and function knob. The switch includes a 20 A circuit breaker. See FIG. 4. Control knobs (HC) set temperature of component A and B heaters. Indicator lights (HL) turn on when thermostats are heating, and off when heater reaches setpoint. Present on heated units only. Heater Power Switch/Circuit Breaker See FIG. 3. Switch (HP) turns power on to heater thermostats.
Setup Setup 1. Locate Reactor E-10 a. b. 2. Locate Reactor E-10 on a level surface. Do not expose Reactor E-10 to rain. a. b. Electrical requirements c. Improper wiring may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician perform any electrical work. Be sure your installation complies with all National, State and Local safety and fire codes. Connect Reactor E-10 to the correct power source for your model. See TABLE 2.
Setup Table 2: Electrical Requirements Model Required Power Source 120 V, 1 phase, 50/60 Hz, two 15 ft (4.5 m) power cords, Heated 240 V, 1 phase, 50/60 Hz, two 15 ft (4.5 m) power cords, Heated Two separate, dedicated circuits rated at minimum of 15 A each Two separate, dedicated circuits rated at minimum of 10 A each Power Cord Connector Two NEMA 5-15T Two IEC 320, with two local adapters: Euro CEE74 Adapter Australia/China Adapter 240 V, 1 phase, 50/60 Hz, one 15 ft (4.
Setup To avoid electric shock, always unplug both cords before servicing Reactor E-10. 1 Ensure no other high amp loads are connected while running Reactor E-10. 2 To verify separate circuits, plug in Reactor E-10 or a worklight and cycle breakers on and off. 1 2 Heater Power 1 Motor Power TI7061a FIG. 5. Use Two Separate Circuits for Two Cord Models 4. 5. Connect fluid hoses 6. Connect main air supply Connect fluid supply hoses to outlet hose connections (R, FIG. 6).
Setup Heated Units S R A (ISO) B (RES) Q Z WL D AIR Nonheated Units R A (ISO) Q B (RES) Z WL D AIR FIG. 6.
Setup 8. 9. Fill wet-cups Fill fluid tanks Keep the felt washers in the pump wet-cups saturated with Graco ISO pump oil, Part No. 217374. The lubricant creates a barrier between the ISO and the atmosphere. NOTICE To prevent cross-contamination of fluids and equipment parts, never interchange component A (isocyanate) and component B (resin) parts or containers. Pump rod and connecting rod move during operation. Moving parts can cause serious injury such as pinching or amputation.
Setup a. Lift hose rack. Remove tank A cover and pour ISO into tank A (red side, with desiccant filter in cover). Replace cover 1 . TI7017a 10. Purge air and flush fluid from lines a. Desiccant filter is blue when fresh, and turns pink when saturated. Be sure shipping plugs are removed from openings on desiccant filter. b. Remove tank B cover and pour resin into tank B (blue side). Replace cover 1 .
Setup e. h. Turn on Motor Power. When clean fluids exit both recirculation tubes (P), set function knob to Stop/Park f. Set Recirc/Spray valves to Recirc. i. g. . Set function knob to Slow Recirc or Fast Recirc OR . j. Replace recirculation tubes in supply tanks. On nonheated units, purge the hoses through the gun without a static mixer installed. For heated units, continue with Startup of Heated Units, page 22. Nonheated units are ready to spray/dispense. Go to Spraying/Dispensing, page 25.
Startup of Heated Units Startup of Heated Units 3. Some models heat the fluid, which can cause equipment surfaces to become very hot. To avoid severe burns: • Do not operate Reactor E-10 without all covers and shrouds in place. • Do not touch hot fluid or equipment. • Allow equipment to cool completely before touching it. • Wear gloves if fluid temperature exceeds 110°F (43°C). 1. Perform Setup, pages 15-21. 2. Set function knob to Slow Recirc 4. 5. or Fast Recirc .
Startup of Heated Units Heatup Guidelines The fluids must be circulated from the pumps through the heaters, hoses, and back to the tanks to ensure warm fluids are supplied to the gun. Heat Management Tips • Heaters perform better with lower flow rates or smaller mix modules. • Triggering the gun for short periods helps maintain efficient heat transfer, keeping material at the desired temperature.
Startup of Heated Units Heating Foam Resins with 245 fa Blowing Agents c. Fill tanks, page 19. d. Set Recirc/Spray valves to Recirc. New foam blowing agents will froth at temperatures above 90°F (33°C) when not under pressure, especially if agitated. Never fill the 7 gal. (26 l) supply tanks beyond the 5 gal. (19 l) line on the tanks, to leave room for some frothing. e. Set function knob to Slow Recirc At High Ambient Temperature (above 75°F/24°C) • Pour resins slowly to avoid frothing.
Spraying/Dispensing Spraying/Dispensing Use lower pressures for joint filling applications. For air operated guns only: Air is supplied to spray gun with gun piston safety lock or trigger safety lock engaged and gun fluid manifold valves A and B closed (if present). If using 2K Manual Dispense Valve, see dispense valve instruction manual. Fusion 1. MD2 4. Check fluid pressure gauges to ensure proper pressure balance.
Pause (Heated Units) 6. Disengage piston safety lock or trigger safety lock. ti10441a Fusion 7. 3. 4. MD2 Test spray onto cardboard or plastic sheet. Verify that material fully cures in the required length of time, and is the correct color. Adjust pressure and temperature to get desired results. Equipment is ready to spray. Set Recirc/Spray valves to Recirc until temperature readouts come back up.
Pressure Relief Procedure Pressure Relief Procedure Shutdown 1. 1. For longer breaks (more than 10 minutes), use the following procedure. If you will be shut down for more than 3 days, first see Flushing, page 29. Engage piston safety lock or trigger safety lock. 2. Fusion 2. MD2 ti10442a Set function knob to Stop/Park If using an impingement mix gun, close gun fluid valves A and B. Doing this will keep the internal parts of the gun cleaner and prevent crossover. . 3. 3.
Maintenance Maintenance • Check pump wet-cups fluid level daily, page 19. • Do not overtighten packing nut/wet-cup. Throat u-cup is not adjustable. • Keep component A from exposure to moisture in atmosphere, to prevent crystallization. • Wipe supply tank lid o-ring and inner rim daily to prevent ISO crystallization. Keep film of grease on o-ring and inside of lid. • Check desiccant filter weekly. Filter is blue when fresh, and turns pink when saturated.
Flushing Flushing 2. Flush equipment only in a well-ventilated area. Do not spray flammable fluids. Do not turn on heaters while flushing with flammable solvents. • Generally, flush if you will be shut down for more than 3 days. Flush more often if material is moisture sensitive and humidity is high in the storage area, or if material may separate or settle out over time. • Flush out old fluid with new fluid, or flush out old fluid with a compatible solvent before introducing new fluid. • 4.
Flushing 7. 8. 9. 10. Set function knob to Stop/Park Purge Gun Hoses (Nonheated Units Only) Wipe out any remaining material from the supply tanks. Fill each supply tank with 1-2 gal. (3.8-7.6 l) of solvent recommended by your material manufacturer. Disconnect hoses from gun and secure back into the tanks for thorough cleaning with solvent. Set function knob to Fast Recirc . Pump solvent through system to waste containers.
Troubleshooting Troubleshooting Status Codes Determine the status code by counting the number of times the status indicator (ST) blinks. ST In this example, B side pressure is higher, so use the B side valve to balance pressures. Turn Recirc/Spray valve only enough to balance pressure. If turned completely, all pressure will bleed off. 3. Check fluid inlet strainers (51a, page 28) and fluid filters at gun. 4. Clean or change restrictor at mixer manifold if using disposable mixer gun kit.
Troubleshooting Status Code 1 and 2 Settings OFF 1 2 3 4 1. Locate switch SW2 on the control board, page 47. TI7023a 1 2 3 4 ON (Default) TI7024a 2. Set the four DIP switches to the desired FIG. 7. DIP Switch (SW2) Settings positions. See FIG. 7 and TABLE 5 on page 32.
Troubleshooting Status Code 5: Excessive Current Draw Status Code 6: High Motor Temperature Shut off unit and contact distributor before resuming operation. Motor is running too hot. 1. Locked rotor; motor unable to turn. Replace motor, page 51. 2. Short on control board. Replace board, page 46. 3. Worn or hung up motor brush causing arcing of brush at commutator. Replace brushes, page 52. 1. Motor temperature too high.
Troubleshooting Troubleshooting Chart PROBLEM Reactor E-10 does not operate. CAUSE No power. SOLUTION Plug in power cord. Cycle Motor Power off then on Motor does not operate. Power turned on with function knob set to a run position. , to reset breaker. Set function knob to Stop/Park , then select desired func- Loose connection on control board. Worn brushes. Fan not working. Broken or misaligned brush springs. Brushes or springs binding in brush holder. Shorted armature.
Troubleshooting PROBLEM Pressure is higher on one side when setting pressure with function knob. CAUSE Pump intake valve partially plugged. Air in hose. Fluid is compressible. Unequal size hoses or unequal hose construction. Pressures are not balanced when Unequal viscosities. running, but pressure is generated and holds on both strokes. Pressure is higher on B side during startup of recirculation, especially in High Recirc mode. Resin froths and overflows tank after refilling hot equipment.
Troubleshooting PROBLEM A side rich; lack of B side. B side rich; lack of A side. No temperature display (heated units only). CAUSE SOLUTION A side gauge is low. B side restriction downstream of gauge. Check gun check valve screen, mix module, or mix manifold restrictor. B side gauge is low. B side material supply problem. Check B side inlet strainer and pump intake valve. A side gauge is low. A side material supply problem. Check A side inlet strainer and pump intake valve. B side gauge is low.
Troubleshooting PROBLEM CAUSE No heat, and heater indicator light Heater Power shut off, or circuit is off. breaker tripped. SOLUTION Cycle Heater Power off then on , to reset circuit breaker. Bad thermostat. With power on, check for continuity at clicks of heater control knob. To replace thermostat, see 311210. Bad overtemperature sensor (this With power on, check for continuis a high temperature limit fuse ity at overtemperature sensor. To and must be replaced if blown). replace sensor, see 311210.
Troubleshooting 38 311075U
Repair Repair Before Beginning Repair Removing Supply Tanks Displacement pump repair and parts information is included in manual 311076, which is supplied with your unit. Repairing this equipment requires access to parts which may cause electric shock or other serious injury if work is not performed properly. Have a qualified electrician connect power and ground to main power switch terminals, see page 15. Be sure to shut off all power to the equipment before repairing. 1. Flush if possible, see page 29.
Repair Recirc/Spray Valves 2. See FIG. 8. Disassemble Recirc/Spray valves. Clean and inspect all parts for damage. Ensure that the seat (503a) and gasket (503b) are positioned inside each valve cartridge (503). 1. See Before Beginning Repair, page 39. Relieve pressure, page 27. 3. Apply PTFE pipe sealant to all tapered pipe threads before reassembling. 4. Reassemble in reverse order, following all notes in FIG. 8.
Repair Displacement Pump To Remove Intake Valve Only Displacement pump repair and parts information is included in manual 311076, which is supplied with your unit. Use dropcloth or rags to protect Reactor E-10 and surrounding area from spills. If pump is not generating any pressure, the intake ball check may be stuck closed with dried material. If the pump is not generating pressure on the downstroke, intake ball check may be stuck open. Either of these conditions can be serviced with the pump in place.
Repair To Remove Entire Pump Assembly 5. Disconnect fluid inlet (C) and outlet (D) lines. Also disconnect steel outlet tube (16) from heater inlet. 217 16 222 6. Remove pump rod cover (222). Push clip up in back and push pin (217) out. Loosen locknut (218) by hitting firmly right-to-left with a non-sparking hammer. Unscrew pump. See manual 311076 for pump repair and parts. D E 7. Install pump in reverse order of disassembly, following all notes in FIG. 9. Clean strainer (51).
Repair Control Module Replace Temperature Display and Sensor (Heated Units Only) Change Display Temperature Units (°F/°C) Unit is shipped with temperature displays set to °F. 1. See Before Beginning Repair, page 39. Relieve pressure, page 27. 2. Remove temperature sensor (424): 1. Shut off Motor Power. Disconnect power supply. a. Remove snap ring (66d) in thermowell housing (66e). See FIG. 10. b. Pull sensor (424) and spacer (66g) out of thermowell housing. 2.
Repair 8. Reassemble in reverse order. Mount temperature display so Heater Power switch off (0) position is at left when facing control panel. (P) faces up. Install knob on shaft so slot (S) engages alignment pin in knob. Push knob onto shaft against detent spring before tightening setscrews (416a). 7. Reconnect potentiometer wires to J2 as shown in FIG. 12. 66e 424 66g 66d TI7067b FIG. 10. Temperature Sensor Replace Function Knob/Potentiometer 1. See Before Beginning Repair, page 39.
Repair Detail of Function Knob/Potentiometer 415 P 404 N S 405 402 404 416a 416 416a 401 N 415 416a TI7076a 416 421 416a 417 *402 *403 409 408 *424 CS 407 CS FC 406 412 FC 410 410* 411 413 424* * These items are not included on the nonheated display. TI6979a FIG. 11.
Repair Control Board Power Bootup Check There is one red LED (D11) on the board. Power must be on to check. See FIG. 12 for location. Function is: • • • • Startup: 1 blink for 60 Hz, 2 blinks for 50 Hz. Motor running: LED on. Motor not running: LED off. Status code (motor not running): LED blinks status code. Control Board Replacement Table 6: Control Board Connectors (see FIG.
Repair Heated Models LINE P1 P1 Motor Power On/Off (20 A Breaker) P2 Heater A Heater Power On/Off (20 A Breaker) LINE P2 Single Cord Models Only J1 Black Twin Flat Cable Fa J9 Red Black Yellow Yellow Red Black Status Indicator Black Sheath Jumper Jumper CONTROL BOARD J7 not used Cycle Counter J11 (120 V Board) J11 J4 Motor Heater B OFF 1 2 3 4 1 2 3 4 5 6 7 8 9 10 Function Knob ON SW2 (see page 32 to adjust J10 D11 not used J14 J15 2 pin red connectors J2 Black White Red J
Repair Fluid Heaters (if supplied) Pressure Transducers Fluid heater repair and parts information is included in manual 311210, which is supplied with heated units. 1. See Before Beginning Repair, page 39. Relieve pressure, page 27. To replace a pressure transducer, see at right. 2. Remove access cover (39) at back of control module to expose control board (406). 3. Disconnect transducer cables from J3 and J8 at board; see FIG. 12, page 47.
Repair Drive Housing Removal B side crankshaft (210) includes the cycle counter magnet (224). When reassembling, be sure to install crankshaft with magnet on B side. If replacing crankshaft, remove magnet (224). Reinstall magnet in center of offset shaft on new crankshaft. Position shaft in Park position. 1. See Before Beginning Repair, page 39. Relieve pressure, page 27. 2. Remove screws (207) and end covers (221, 227), FIG. 14. Examine connecting rod (216).
Repair Cycle Counter Switch Replacement B side drive housing cover (227) includes the cycle counter switch (223), mounted in the cover. When reassembling, be sure to install cover with switch on B side. 223 0.6 in. (15.2 mm) from inside edge 1.0 in. (25.
Repair Electric Motor Test Motor If motor is not locked up by pumps, it can be tested using a 9 V battery. Open recirculating valves, disconnect J4 or J11 from control board, see FIG. 12, page 47. Touch jumpers from battery to motor connections. Motor should turn slowly and smoothly. Removal If replacing a component with electrical cabling, remove one supply tank, page 39. e. Thread motor power switch harness out bottom of control module and cable channel, to free motor. NOTICE Motor is heavy.
Repair Motor Brushes Replace brushes worn to less than 1/2 in. (13 mm). Brushes wear differently on each side of motor; check both sides. Brush Repair Kit 287735 is available; kit includes instruction sheet 406582. Motor commutator should be smooth. If not, resurface commutator or replace motor. 202 37 TI7030a FIG. 15. Fan 1. See Before Beginning Repair, page 39. Relieve pressure, page 27. 2. See instruction sheet 406582, included with Brush Repair Kit 287735.
Repair 311075U 53
Parts Parts Part No. AP9570 or CS9570, 120 V, 15 A, Heated Package Part No. AP9571 or CS9571, 240 V, 10 A, Heated Package Part No.
Parts Part No. 249806, 120 V, 15 A, Nonheated Package, MD2 Part No. 249808, 240 V, 10 A, Nonheated Package, MD2 Part No. 24R984, 120 V, 15 A, Nonheated Package, 2K Dispense Part No. 24R985, 240 V, 10 A, Nonheated Package, 2K Dispense 61 61 101 255325 103 24R021 103 102 249633 WL D 102 24R823 Quantity Ref.
Parts Part No. 249570, 120 V, 15 A, Heated Proportioner Part No. 249571, 240 V, 10 A, Heated Proportioner Part No.
Parts Heated Proportioners Ref. Part Description Qty 1 24R382 CART; see page 67 1 2 24L000 TANK, with lid and outlet fitting; 2 LDPE; includes item 2a 2a 15F895 . O-RING, lid, tank 1 4 111800 SCREW, cap, hex hd; 5/16-18 x 12 5/8 in. (16 mm) 5 24K984 DRYER, desiccant 1 6 24K976 MUFFLER, vent 1 7 101044 WASHER, plain; 1/2 in. (13 mm) 1 8 119973 LANYARD; 14 in.
Parts Ref. 66 66a 66b‡ Part 24E555 121063 123787 66c‡ 123788 66d 66e 66f 66g 66h 555561 16C785 16C786 16C787 113641 Description Qty KIT, temperature sensor 2 O-RING, fluroroelastomer 1 FITTING, elbow, 45°; 3/8 jic x 1 1/4-18 npt FITTING, elbow, 45°; 5/16 jic x 1 1/4-18 npt RING, retaining, 3/8 1 HOUSING, thermowell 1 MANIFOLD, fluid 1 SPACER, sensor 1 GAUGE, pressure, fluid; sst 1 * Included in 287718 Pump Inlet Kit (one side). ‡ 24E555 Kit includes “A” and “B” side adapters.
Parts 311075U 59
Parts Part No. 249576, 120 V, Nonheated Proportioner Part No.
Parts Nonheated Proportioners Ref. Part Description Qty 1 24R382 CART; see page 67 1 2 24L000 TANK, with lid and outlet fitting; 2 LDPE; includes item 2a 2a 15F895 . O-RING, lid, tank 1 4 111800 SCREW, cap, hex hd; 5/16-18 x 12 5/8 in. (16 mm) 5 24K984 DRYER, desiccant 1 6 24K976 MUFFLER, vent 1 7 101044 WASHER, plain; 1/2 in. (13 mm) 1 8 119973 LANYARD; 14 in.
Parts Part No. 287655, 120 V Bare Proportioner Part No. 287656, 240 V Bare Proportioner 207 201 (Ref) 206 203 207 205 204 202 ‡221 208* 209* 210* 37 224 211* 215‡ 223 220‡ 227 207‡ 201 †212 †213 †214 †213 222‡ ◆216 218 220‡ 219 217◆ 207‡ TI6978a Ref.
Parts Part No. 249499, Insulated Hose Bundle with recirculation lines 301 302 (Ref) 302 304 303 (Ref) 305 Ref. 301 302 303 TI6991a Part Description Qty 249508 HOSE, fluid (component A), mois2 ture guard; 1/4 in. (6 mm) ID; no. 5 JIC fittings (mxf); 35 ft (10.7 m) 2 249509 HOSE, fluid (component B); 1/4 in. (6 mm) ID; no. 6 JIC fittings (mxf); 35 ft (10.7 m) Ref. 303 304 305 Part Description Qty 1 15G342 HOSE, air; 1/4 in. (6 mm) ID; 1/4 npsm (fbe); 35 ft (10.
Parts Part No. 24L004, 120 V Heated Display Part No. 24L005, 240 V Heated Display 404 402 414 405 416a 416 416a 401 404 (Ref) 421 415 417 402 403 409 408 407 406 412 410 411 410 413 424 TI6979a Ref.
Parts Part No. 249537, 120 V Nonheated Display Part No. 249538, 240 V Nonheated Display 403 405 414 416a 402 404 416 416a 401 404 (Ref) 415 421 417 409 410 408 406 407 423 411 412 413 Ref.
Parts Part No. 24L009 Recirculation Manifold, Heated Models 505 504 Ref. 501 502 503 Part 24K993 111763 239914 503a 503b 504 505 506 507 508 15E022 111699 224807 187625 111600 100721 100840 509 510 116704 119998 503 506 503a 503b ▲512 501 508 502 512▲ 189285 507 510 Description Qty MANIFOLD, recirculation 1 ELBOW; 1/4 npt (mbe) 2 VALVE, recirc/spray; includes 2 items 503a, 503b . SEAT 1 .
Parts Part No. 249582, Cart 612 611 607 609 608 603 602 602 604 612 605 610 604 606 WL D Ref.
Suggested Spare Replacement Parts Suggested Spare Replacement Parts Keep the following spare parts on hand to reduce downtime.
Dimensions Dimensions LQ PP All Models ti6974b LQ 311075U P P PP Q L 69
Technical Data Technical Data Maximum fluid working pressure Electrical requirements 2000 psi (14 MPa, 140 bar) Model AP9570, CS9570: 120 Vac, 1 phase, 50/60 Hz, 3500 W; requires two separate, dedicated 15 A circuits Model AP9571, CS9571: 240 Vac, 1 phase, 50/60 Hz, 3800 W; requires two separate, dedicated 10 A circuits Model AP9572, CS9572: 240 Vac, 1 phase, 50/60 Hz, 3800 W; requires a single dedicated 16 A circuit Model 249806, 24R984: 120 Vac, 1 phase, 50/60 Hz, 1800 W; requires a single dedicated 15
Technical Data Tank Capacity Fluid Outlets Fluid Circulation Returns Air Inlet Air Outlet Gun Compressed Air Requirements Hose Markings Weight (empty) Wetted Parts 7 gal. (26.5 liters) each (nominal) Component A (ISO): -5 JIC male Component B (RES): -6 JIC male Component A (ISO): -5 JIC male Component B (RES): -6 JIC male 1/4 in. quick-disconnect industrial type pin fitting 1/4 npsm(m) Fusion Gun (purge air and operating air): 4 scfm (0.112 m3/min) MD2 Gun with disposable mixer kit: 14 scfm (0.
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
