Instructions - Parts List Mini Fire-Ball® 225, 50:1 Grease Pump Packages 309967C EN Portable units for dispensing heavy grease. See page 2 for model numbers. 5000 psi (34 MPa, 345 bar) Maximum Working Pressure 100 psi (0.7 MPa, 7 bar) Maximum Air Working Pressure Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.
Models Models Model No.
Warnings Warnings The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual, refer back to these pages for a description of the specific hazard. WARNING EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury.
Operation/Service WARNING FIRE AND EXPLOSION HAZARD When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources, such as cigarettes and portable electric lamps. • Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
Installation Installation Air compressor: follow manufacturer’s recommendations. General Information Dispense valve: ground through connection to a properly grounded fluid hose and pump. NOTE: Reference numbers and letters in parentheses in the text refer to the callouts in the figures and parts drawing. NOTE: Always use genuine Graco parts and accessories, available from your Graco distributor. Fluid supply container: follow local code.
Installation Typical Installation The installation shown below is only a guide for selecting and installing system components and accessories. Contact your Graco distributor for assistance in designing a system to suit your particular needs.
Installation Models 246910, 253362, and 253384 (FIG. 2) 1. Remove the cover from the pail, and scoop the lubricant from the center to the sides of the pail to make its surface concave. through the follow plate grommet. The pump stop plate(4b) will secure the pump in place. 4. Place the cover (4a) on the pail, and tighten the thumbscrews (4f). 2. Center the follow plate (5) in the pail opening.
Installation Models 246911, 246913, 253385 and 253386 (FIG. 3) 4. Secure the cover (4) on the pail with the three thumbscrews (A). 1. Remove the fluid outlet adapter included with the pump, and screw the holster (6) into the pump outlet using thread sealant. 5. Install shim (11) on top of drum. Align holes in shim with holes in cover (4). 2. Models 246913 and 253386: Assemble the truck (7) as shown in the parts drawing on page 13.
Installation Models 246914, 246917, 253387 and 253390 (FIG. 5 and FIG. 4) 3a 1. Remove the cover from the pail, and scoop the lubricant from the center to the sides of the pail to make its surface concave. 9b 3c 2. Center the follow plate (5) in the pail opening. Press the follow plate firmly downward and rotate it over the lubricant surface to eliminate air pockets and prevent channeling. 4 3. Place the cover (4) on the pail and tighten the thumbscrews (A). 11 A 4.
Installation Models 246915, 246916, 253388 and 253389 9b (FIG. 6) 1. For Models 246915 and 253388: Assemble the portable base (8) as shown in the parts drawing on page 15 2c, 2d 4 2b For Models 246916 and 253389: Assemble the truck (7) as shown in the parts drawing on page 15. 6 A 2. Remove the fluid outlet adapter included with the pump, and screw the holster (6) into the pump outlet, using thread sealant. 11 3.
Operation Operation Pressure Relief Procedure 1. Shut off the air to the pump. 2. Bleed off the air pressure by closing the air regulator (self–relieving type), or closing the bleed–type master air valve installed upstream of the air regulator, or disconnecting the air supply hose at the quick–disconnect. 3. Hold a metal part of the gun or valve firmly to the side of a grounded metal waster container and trigger to relieve fluid pressure. Start–up: Single or Multiple Pump Systems 1.
Parts Parts Models: 246910, 253362, 253384 35-50 lb (16-23 kg) pail size . Ref. Part 1 2 Description Qty 246909 PUMP, Mini Fire-Ball 225 50:1 (with handle) See manual 309966 for parts. 1 253361 PUMP, Mini Fire-Ball 225 50:1 (without handle) Model 253362 See manual 309966 for parts. 1 236058 DISPENSE KIT; 12 ft (3.7 m) hose; See parts list on page 17.
Parts Models: 246911, 253385 35-50 lb (16-23 kg) pail size Ref Part Description Models: 246913, 253386 35-50 lb (16-23 kg) pail size Qty Ref Part Description Qty 1 246909 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 1 246909 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 2 236058 DISPENSE KIT; 12 ft (3.7 m) hose; See parts list on page 17. 1 2 236058 DISPENSE KIT; 12 ft (3.7 m) hose; See parts list on page 17. 1 4 204574 COVER, model 253385.
Parts Models: 246914, 253387 120 lb (55 kg) drum size Ref Part Description 3 1 246780 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 3 222072 Hose and Fitting Kit; 6 ft (1.8 m) hose; See parts list on page 17. 1 4 204574 COVER, model 253387. See manual 306345 for parts. 1 24R350 COVER, model 246914. See manual 306345 for parts. 1 220654 FOLLOW PLATE, model 253387. See manual 306345 for parts. 1 24F902 FOLLOW PLATE, model 246914. See manual 306345 for parts.
Parts Models: 246915, 253388 120 lb (55 kg) drum size Ref Part Models: 246916, 253389 120 lb (55 kg) drum size Description Qty Ref Part Description Qty 1 246780 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 1 246780 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 2 236058 DISPENSE KIT; 12 ft (3.7 m) hose; See parts list on page 17. 1 2 236058 DISPENSE KIT; 12 ft (3.7 m) hose; See parts list on page 17. 1 4 204574 COVER, model 253388.
Parts Models: 246917, 253390 400 lb (180 kg) drum size Ref Part Description Qty 1 246781 PUMP, Mini Fire-Ball 225 50:1 See manual 309966 for parts. 1 3 222072 Hose and Fitting Kit; 6 ft (1.8 m) hose; See parts list on page 17. 1 4 200326 COVER See manual 306345 for parts. 1 5 223845 FOLLOW PLATE, model 253390. See manual 306345 for parts. 1 24F903 FOLLOW PLATE, model 246917. See manual 306345 for parts. 1 9 240979 CE Kit for 253389 See parts on page 19.
Parts Components and Kits Ref No. 2: Dispense Kit 236058 Ref Part Description Ref No. 3: Hose and Fitting Kit 222072 Qty Ref Part Description Qty 2a 109151 HOSE; 1/4 npt(mbe) x 12 ft (3.7 m) 1 3a 203320 HOSE; air, buna-N; 3/8 npt(mbe) x 6 ft (1.
Parts Ref No. 7: Truck 203650 Ref Part Ref No. 8: Portable Base 203622 Description Qty Ref Part Description Qty 7a 203651 BASE, truck; bare 1 8a 191750 BASE, drum 1 7b 101251 WHEEL 2 8b 102547 2 7c 159912 NUT, thumb, 5/16-18 2 BOLT, hex head; 5/16”-18 x 1.5” 7d 159913 CLAMP, hold down; (for steel drums only) 2 8c 100214 WASHER, lock 2 8d 191747 BRACKET 2 2 7e 154636 WASHER, 5/8”, 16 GA 4 8e 100132 WASHER, flat 7f 100609 SCREW, machine, panhead; 1/4-20 x 0.
Sound Data Ref No.9: CE Kit 240979 9b Ref Part Description Qty 9a 156849 NIPPLE 1 9b 109075 REGULATOR, air, with gauge 1 9c 103347 VALVE, safety 1 9d 222011 CLAMP, grounding 1 9e † CE Label (not shown) 1 † Attention: To comply with CE directives, the CE identification label must be affixed to the back of the cart or to the top of the drum cover. Permanently mark the date of assembly on the label. 9a 9c 9d FIG.
Graco Information For the latest information about Graco products, visit www.graco.com. For patent information, see www.graco.com/patents. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590 All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
