LADDER SHELF WITH STORAGE 1/19
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION AL AR B / nt Fro / nt Fro t/ Fron Fro nt / nt Ava Ava nt Fro nt nt Ava LEFT SIDE QTY 1 C /A vant t an Av E / nt Fro t an Av / nt Fro G FR / nt Fro / nt Fro t an Av LEFT SIDE PANEL QTY 1 t an Av TOP SHELF CABINET QTY 1 SHELF QTY 1 SHELF QTY 1 FL SHELF QTY 1 RIGHT SIDE QTY 1 D / nt Fro t an Av Fro nt / t an Av Av an t RIGHT SIDE PANEL QTY 1 BOTTOM SHELF CABINET QTY 1 5/19
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION I H BACK PANEL QTY 1 KL J DRAWER FRONT QTY 2 L KR LEFT DRAWER SIDE QTY 2 DRAWER BACK QTY 2 RIGHT DRAWER SIDE QTY 2 DRAWER BOTTOM QTY 2 6/19
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 1 2 3 ALLEN KEY BOLT M6 x 50 mm QTY 4 ALLEN KEY BOLT M6 x 30 mm QTY 10 5 4 ALLEN KEY SCREW M6 x 30 mm QTY 8 ALLEN KEY BOLT & CROSS NUT M6 X 50 mm QTY 12 SETS 6 WOOD BOLT CAP QTY 12 7 9 8 PHILLIPS SCREW ROUND HEAD M4 x 15 mm QTY 12 ALLEN KEY QTY 1 HANDDLE M4 x 25 mm QTY 2 SET CAM LOCK PIN CAM LOCK QTY 8 SET 10 a. M4 X 25 - QTY 2 ( 1 is extra ) b. M4 X 15 - QTY 1 c.
COMPONENTS–KEY DIAGRAM AL AR / nt Fro / nt Fro / nt Fro B C D H / nt Fro nt nt Ava nt Ava FL Fro nt Ava E nt Ava t van /A nt Fro / nt Fro nt Ava G t van /A FR nt Fro t van /A J KL I L KR 8/19
ASSEMBLY STEP 1 I KL 9 KR 9 1. A ach four Cam Lock Pins 9 to back of Drawer Front I . 2. Align Cam Lock Pins with guide holes and a ach Drawer Sides KL , KR . 3. Insert two Cam Locks 9 into guide holes on each Drawer Side KL , KR . 4. Use flathead screwdriver secure Cam Locks. STEP 2 KR L KL I 1. Slide Drawer Bo om L firmly into slots on Drawer Sides KL ,KR and Drawer Front I .
ASSEMBLY STEP 3 J KR 4 L KL 6 1. Align Drawer Back J with Drawer Sides KL , KR . 2. A ach back using two Allen Key Screws 4 through guide holes on each Side KL , KR . 3. Use Allen Key 6 to ghten screws. Do not over- ghten. STEP 4 8 I 8 1. Use Phillips Screwdriver to a ach Handle 8 to Drawer Front I . Repeat Step 1-4 for the second drawer. NOTE: The screwdriver is not included in the hardware pack.
ASSEMBLY STEP 5 1 6 Front / Avant E Front / Avant FR Front / Avant FL 1. Attach Top Shelf Cabinet E to Side Panels FL , FR using four Allen Key Bolts 1 . 2. Use Allen Key 6 to tighten Bolts. Do not over-tighten.
ASSEMBLY STEP 6 2 6 Front / Avant Front / Avant FR FL Front / Avant Front / Avant G 1. Attach Bottom Shelf Cabinet G to Side Panels FL , FR using four Allen Key Bolts 2 . 2. Use Allen Key 6 to tighten Bolts. Do not over-tighten.
ASSEMBLY STEP 7 Fro nt / Fro nt / Ava nt Ava nt H 7 1. A ach Back Panels H to back of assembled ( E,FL ,FR,G ) using Phillips Screws Round Head 7 into guide guide holes. 2. Use Phillips screwdriver to ghten screws. Do not over- ghten.
ASSEMBLY STEP 8 B AL / nt Fro C nt Ava / nt Fro nt Ava FR D nt Fro / nt Fro t van /A nt Ava E / nt Fro G nt Ava / nt Fro / nt Fro nt Ava nt Ava / nt Fro 3 FL 3 3 3 nt Ava 6 3 1 3 3 nt / 6 nt Ava Fro 3 1. A ach Shelves B C D to Le Side AL . 2. Insert Cross Nuts 3 into guide holes in Shelves B C D with the slot facing out. Use a flathead Screwdriver to turn it to align with the Bolts 3 . 3. A ach assembled (E,FL,FR,G,H) to Le Side AL using 3 Allen Key Bolts 1 . 4.
ASSEMBLY STEP 9 3 6 3 3 3 3 / nt Fro nt Ava 3 AR 1 6 B / nt Fro nt Ava / nt Fro AL FR C nt Ava / nt Fro nt Ava D / nt Fro nt Ava E / nt Fro G nt Ava / nt Fro nt Ava FL 1. To a ach Shelves B C D and assembled (E,FL,FR,G,H) to Right Side AR, repeat step 8.
ASSEMBLY STEP 10 5 / nt Fro / nt Fro nt Ava nt Ava 5 / nt Fro / nt Fro nt Ava 5 nt Ava nt Fro ant / Av nt / Fro ant Av 1. Insert twelve Wood Bolt Caps 5 into exposed bolt holes on Sides A .
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 11 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
WARRANTY Thank you for purchasing our product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. We reserve the right to repair or replace the defective product, at its discretion. This product is guaranteed for 12 months if used for normal purposes.
