Dresser IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft sloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. I Back Panel Part List E. Front Rail pes. Jo Back Panel Drawer Front Drawer Side L5. 4 pes. 3 pes. K5. Di rawer Bottom Drawer Bettors 6 pes. / 2 pes.
( Assembly Instructions 2/12 ) IMPORTANT » Lie 3 soft cloth between these parts and the flora, * Do not use power tools above 8 volts to assemble. Do not tighten all the screws until each part s properly assembled. = The unit must be revel to work properly. Use the included adjustable levelers to label, STEP 1 Insert Cam Lock Screws into the per-drilled holes in Top (A), Side Panels (8}, Front Rails {F), (G} and Back Panels (J), then tighten.
( Assembly Instructions 3/12 ) STEP 2 Assemble Back Panels {} and {J) with Cam Locks. {See Figure 1) /’1 1/4" Round Head Screw g STEP 3 Attach Front Rails (E) and {F} to Divider (D) with Cam Locks. Attach Front Rail {G) to Divider {D} with 1 174" Round Head Screw.
( Assembly Instructions 4/12 ) STEP 4 Attach unit from Step 2 to unit from Step 3 with Dowels and 11/4" Round Head Screws. < T~ Je— STEP 5 Attach unit to Side Panel {B) with Cam Locks.
( Assembly Instructions 5/12 ) STEP 6 Attach Side Panel {C) 1o unit with Cam Locks. STEP 7 Attach Bottom {H) to unit with Dowels, Cam Locks and 1 1/4" Round Head Screws.
( Assembly Instructions 6/12 ) STEP 8 Attach Top {A) to unit with Dowels, Cam Locks and 1 3/4" Round Head Screws. Note: A Philips screwdriver 5" or less in length is recommended. Lee! unit by adjusting the adjustable levelers on bottom of unit. {See Figure 2} Note: Unit must be elev! to work properly.
C IMPORTANT Assembly Instructions 7/12 » Ta help reduce the rig of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 9 Place unit at desired location. Mark wall with pencil just above and in-line with hole in Top (A). {See Figure 3) Move unit. Drill a 3/8" hole in wall 1 1/2” below mark. Insert Anchor into wall hole and attach Tip-over Restraint to Anchor with 1 1/2” Round Head Screw and Flat Washer.
( Assembly Instructions 8/12 ) Drawer (K) STEP 10 Attach Drawer Sides (K3}, (K4) and Drawer Supports {Ké) to Drawer Back (K2) with 11/4" Fiat Head Screws. Collar st back "1 1/4" Flat Head Screw 1174" Fiat Head Resew ——As. e STEP 11 Insert Drawer Bottom {K5} into groove. Attach Drawer Front (K1) to unit with 1 1/4" Flat Head Screws. STEP 12 Attach Knobs with Machine Screws.
( Assembly Instructions 9/12 ) Drawer (L) STEP 13 Attach Drawer Sides (K3}, (K4) and Drawer Supports {Ké) to Drawer Back (K2) with 11/4" Fiat Head Screws. Roller at back "y 1 1/4" Flat Head Screw 1174" Fiat Head Resew ——As, e STEP 14 Insert Drawer Bottom {L5} into groove. Attach Drawer Front (K1) to unit with 1 1/4" Flat Head Screws. STEP 15 Attach Knobs with Machine Screws. Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 10/12 ) Drawer (M) STEP 16 Attach Drawer Sides (M3}, (M4) and Drawer Supports (K6} to Drawer Back (M2} with 11/4" Fiat Head Screws. Rioter at back STEP 17 Insert Drawer Bottom (L5} into groove. Attach Drawer Front (M1} to unit with 11/4" Flat Head Screws. STEP 18 Attach Handle with Machine Screws. \ Machine Craw Note: Drawer assembly is not complete until 3/4” Flat Head Screws are used in a later step.
( Assembly Instructions 11/12 ) STEP 19 Loosen slightly screws per-installed on back of drawer fronts. 1344 STEP Insert drawers into unit, then U adjust drawer front panels left T ar right and up or down until drawer gaps look proportional. k3K == k-3 STEP 21 Pull each drawer open slowly and re-tighten screws from Step 19. Make sure drawer front panels do not move and lock drawer front panels into position with 3/4" Flat Head Screws.
