Installation & Assembly

1of2
Package Contents
A
B
Fixture
Body
x1
Shade
x1
STEP 1 Install Stem to Fixture
Body
-
A. Place Stem (G) between Tabs on
the side of Fixture Body (A).
Pass Mounting Ball with Bolt (H)
through holes on Tabs and Stem
(G). Thread Mounting Ball (F)
onto bolt and hand tighten until
snug to secure Stem (G).
Figure 1
Tab
D
Lock
Ball
x1
F
Mounting Ball
x3
C
Shade Holder
x1
A
E
Lock
Ball 2
x2
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
BulbRecommended: (5)MediumBase100WMaximum,Alternatebulb(5)23WCFL
EstimatedAssembly Time:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Hardware Contents
AA
Crossbar Assembly
x1
G
Stem
x3
H
Mounting Ball
with Bolt
x3
F
H
G
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
A. Remove mounting balls from the Crossbar Assembly (AA). Fit the
ceiling canopy of the Fixture Body (A) to the Crossbar Assembly
(AA) and secure with mounting balls. Note: The Ceiling Canopy
should be snug against the ceiling and the mounting balls. If not,
adjust the length of the nipple on the Crossbar Assembly (AA) by
unscrewing the preassembled hex nut and lock washer and then
Figure 2
STEP 2 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Outlet Box
screwing the mounting
screws in or out of the
crossbar until the correct
length is achieved. Once the
Ceiling Canopy is secure,
remove the mounting ball
and Ceiling Canopy and
proceed to Step 4.
Ceiling
Canopy
AA
Hex Nut and
Lock Washer
Mounting
Screw
A
Mounting Ball
Figure 3
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy on the Fixture Body (A) over the outlet box. Align the holes
Ceiling
Canopy
AA
Mounting
Screw
A
Mounting Ball
Figure 5
in the Ceiling Canopy with
the mounting screws, then
attach the Ceiling Canopy
using the previously
removed mounting balls.
Hand tighten until snug.
STEP 6 Attach Shade to Fixture Body-
A. Seat Shade (B) inside of Shade Holder (C). Life Shade Holder (C)
with Shade (B) upward. Pass the hole on one Tab at Shade Holder
Assembly Instruction