Product Manual

ManualsBrandsGPI ManualsDC Powered Fuel PumpsGPRO 12V Fuel Transfer Pump — 20 GPM, Automatic Nozzle, Hose

922105-01B

TABLE OF CONTENTS

General Information .................................................... 2

Installation .................................................................. 2

Operation .................................................................... 3

Maintenance ............................................................... 4

Troubleshooting .......................................................... 5

Specications ............................................................. 6

Parts and Service ....................................................... 6

Illustrated Parts Drawing ............................................ 7

Warranty .......................................................See Insert

11/14

To the owner...

Congratulations on receiving your GPRO™ Fuel Transfer

Pump. We are pleased to provide you with a system designed

to give you maximum reliability and efciency.

Your fuel pump is designed, tested, and approved for use with

gasoline (up to 15% alcohol blends such as E15), diesel fuel

(up to 20% biodiesel blends such as B20) and kerosene. Please

take all due precautions when handling these ammable liquids.

Your safety is important to us.

Also, to assure the longest possible service life, it is important

that you follow the operation and maintenance procedures

outlined in this manual. We are proud to provide you with a

quality product and dedicated support. Together with your

conscientious use, we are sure that you will obtain years of

safe, dependable service.

Victor Lukic, President

Great Plains Industries, Inc.

SAVE THESE INSTRUCTIONS

DO NOT RETURN THIS PRODUCT TO

THE STORE!

Please contact Great Plains Industries before returning

any product. If you are missing parts or experience

problems with your installation, our Customer

Support

Department will be happy

to assist you:

800-835-0113 or

316-686-7361

OWNER'S MANUAL

PRO20-012

12-Volt DC

PRO20-012AD Automatic Diesel Nozzle

PRO20-012MD Manual Diesel Nozzle

PRO20-012PO Pump Only

Summary of content (8 pages)

PAGE 1
OWNER'S MANUAL SAVE THESE INSTRUCTIONS PRO20-012 12-Volt DC PRO20-012AD Automatic Diesel Nozzle PRO20-012MD Manual Diesel Nozzle PRO20-012PO Pump Only DO NOT RETURN THIS PRODUCT TO THE STORE! Please contact Great Plains Industries before returning any product. If you are missing parts or experience problems with your installation, our Customer Support Department will be happy to assist you: 800-835-0113 or 316-686-7361 TABLE OF CONTENTS General Information...............................................
PAGE 2
GENERAL INFORMATION The purpose of this manual is to assist you in installing, operating and maintaining your GPRO™ pump. This manual covers 12-volt DC model PRO20-012. Model Components PRO20-012AD: Includes pump, hose and automatic diesel nozzle. PRO20-012MD: Includes pump, hose and manual diesel nozzle. PRO20-012PO: Includes pump only. NOTE: Suffixes MD, AD and PO are for ordering purposes only. Constructions described above are covered as alternate constructions under the Part No. PRO20 UL Listing.
PAGE 3
Install Pump on Tank • Clean the tank interior of all dirt and foreign material. • Place the pump with suction pipe installed on the tank fitting and tighten securely. Make sure the pump is not cross-threaded. • To prevent pressure build-up and possible fuel leaks through the nozzle, make sure the tank is vented. A vent cap rated at 3 psi or less is recommended. Install Electrical Connections The PRO20-012 must be connected to a 12-volt DC power source only.
PAGE 4
After dispensing fuel, push the switch lever forward to turn the pump off and return the nozzle to the holder. The nozzle may be locked in place to prevent unauthorized use by installing a padlock (not provided) through the hole in the top of the nozzle cover. To Clean or Replace Strainer All pump models have an inlet strainer. If flowrate is reduced, clean or replace strainer (see below). The pump is designed to be self-priming.
PAGE 5
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION A. MOTOR DOES NOT RUN 1. Wiring problem Confirm all connections are tight and correct voltage is getting to the pump. 2. Fuse blown Inspect fuse in fuse holder on power cord. If blown, replace. 3. Rotor or vanes jammed Remove coverplate to expose rotor. Remove any obstructions. Check for excessive vane and slot wear. If damaged, replace. 4. Circuit breaker switch defective Replace switch. 5. Motor bad Contact the factory. 1.
PAGE 6
SPECIFICATIONS APPLICATION: Designed to safely transfer low viscosity petroleum fuels such as gasoline (up to 15% alcohol blends such as E15), diesel fuel (up to 20% biodiesel blends such as B20) and kerosene. Pump is designed for permanent mounting on vented storage tanks. PUMP HOUSING: Cast Iron PERFORMANCE: Pump Rate: Up to 20 GPM (76 LPM) Duty Cycle: 30 min. ON, 30 min. OFF Suction Lift: Up to 15 feet (4.
PAGE 7
ILLUSTRATED PARTS DRAWING 17 37 23 30 26 38 14 33 24 28 7 31 15 35 29 18 16 9 22 21 13 8 20 6 5 19 25 34 36 26 12 26 27 11 32 4 10 2 39 Not included with PRO20-012PO Included with PRO20-012MD only Included with PRO20-012AD only 1 Note: Nozzles not included with PRO20-012PO Not included with PRO20-012PO 3 GPRO™ Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Part No.
PAGE 8
M-3020 Motor for Hazardous Locations © 2014 Great Plains Industries, Inc. All Rights Reserved. Made in U.S.A. and GPROTM are trademarks, and the electric gear pump design is a registered trademark of Great Plains Industries, Inc.