Product Manual

ManualsBrandsGPI ManualsAC Powered Fuel Pumps115V Fuel Transfer Pump — 30 GPM, Automatic Nozzle, Hose

Rev. B 921929-03

5252 East 36th Street North

Wichita, KS USA 67220-3205

TEL: 316-686-7361

FAX: 316-686-6746

“A Gr e at Pla i ns Ve ntu r es S ub s idi a ry”

www.gpi.net

1-800-835- 0113

TABLE OF CONTENTS

General Information ..........................................................2

Installation ........................................................................2

Operation ..........................................................................4

Troubleshooting ................................................................5

Illustrated Parts Drawing ..................................................6

Speciﬁcations ...................................................................7

Parts and Service .............................................................7

Great Plains Industries, Inc. is a member of

the Petroleum Equipment Institute.

SAVE THESE INSTRUCTIONS

06/08

To the owner...

Congratulations on receiving your GPI Super Duty Fuel Pump.

We are pleased to provide you with a system designed to

give you maximum reliability and efﬁciency.

Your fuel pump is designed, tested, and approved for use

with gasoline, kerosene, and diesel fuel. Please take all due

precautions when handling these ﬂammable liquids. Your

safety is important to us.

Also, to assure the longest possible service life, it is important

that you follow the operation and maintenance procedures

outlined in this manual. We are proud to provide you with a

quality product and dedicated support. Together with your

conscientious use, we are sure that you will obtain years of

safe, dependable service.

President

Great Plains Industries, Inc.

M-3130 & M-3130-RDP Series

115/230 Volt Super Duty Fuel Pump

M-3130-ML Manual Nozzle

M-3130-AL Automatic Nozzle

M-3130-PO Pump Only

Owner’s Manual

Please contact GPI before returning any

product. If you are missing parts or ex-

perience problems with your installation,

our Customer Support Department will be

happy to assist you.

GPI Customer Support

800-835-0113 or

316-686-7361

Summary of content (8 pages)

PAGE 1
5252 East 36th Street North Wichita, KS USA 67220-3205 TEL: 316-686-7361 FAX: 316-686-6746 SAVE THESE INSTRUCTIONS M-3130 & M-3130-RDP Series 115/230 Volt Super Duty Fuel Pump “ A G r e a t P l a i n s Ve n t u r e s S u b s i d i a r y ” www.gpi.net 1-800-835-0113 M-3130-ML Manual Nozzle M-3130-AL Automatic Nozzle M-3130-PO Pump Only Owner’s Manual Please contact GPI before returning any product.
PAGE 2
GENERAL INFORMATION Your pump is designed for use only with thin viscosity petroleum fuels such as gasoline, diesel fuel and kerosene. Do not use this pump for dispensing any fluids other than those for which it was designed. Using the pump with other fuels can damage components and void the warranty. Additional components such as meters, automatic nozzles and filters must be listed for use with fuel transfer systems.
PAGE 3
2. 3. Place the two bolts through the nozzle cover and then place the two flat washers on the bolts. The washers are used as spacers to set the nozzle hanger away from the switch coverplate. CAUTION Connect pump to the proper voltage source. M-3130 series pumps are designed to operate on 115 VAC, 60 HZ or 230 VAC, 60 HZ. Connection to improper voltage will damage pump. Pump is set at factory for low voltage (115-volt).
PAGE 4
OPERATION The pump contains an automatic bypass valve to prevent pressure buildup when the pump is on but the nozzle is closed. Do not leave the pump on for more than 10 minutes with the nozzle closed. DANGER Never leave the pump running without fluid. Dry running can damage the pump components. To prevent physical injury, observe precautions against fire or explosion when dispensing fuel.
PAGE 5
TROUBLESHOOTING Symptom Probable Cause Corrective Action A. MOTOR DOES NOT RUN 1. No electrical power to pump Check breaker, switchbox and wiring. 2. Auxiliary temperature-limiting device tripped Allow motor to cool. Auxiliary temperature-limiting device will automatically reset. 3. Rotor or vanes jammed Remove coverplate and check for damage or obstruction. B. MOTOR RUNS, BUT NO FLOW 1. Tank level low Add fuel to tank. 2.
PAGE 6
ILLUSTRATED PARTS DRAWING M-3130-RDP ONLY 33 14 13 2 1 3 4 5 8 7 6 10 9 11 12 15 29 28 17 27 16 25 22 18 19 Item No. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 904006-38 133032-02 901003-15 121010-11 133041-1 904006-33 133027-1 906006-53 904006-54 133039-03 133026-1 133521-01 13380801 133058-1 133049-1 904006-57 133042-1 20 23 21 A 133502-1 31 No. Req’d. Hex Head Screw 3/8 - 16 x 1.................2 Coverplate..............................................
PAGE 7
SPECIFICATIONS PARTS AND SERVICE The M-3130 fuel pump is designed to safely transfer low viscosity petroleum fuels such as gasoline, kerosene and diesel fuel. The pump is designed for permanent mounting on vented storage tanks, either in-ground or above-ground. RAINPROOF for outdoor use. In order to preserve the UL Listing for pump safety, return the entire pump to the factory for repair or replacement.
PAGE 8
Limited Warranty Policy Great Plains Industries, Inc. 5252 E. 36 Street North, Wichita, KS USA 67220-3205, hereby provides a limited warranty against defects in material and workmanship on all products manufactured by Great Plains Industries, Inc. This product includes a 2 year warranty.