Product Manual

ManualsBrandsGPI ManualsAC Powered Oil PumpsOil Pump — 8 GPM, 115 Volt

Rev. C 922029-01

05/12

To the owner...

Congratulations on receiving your GPI oil pump. We are

pleased to provide you with a system designed to give

you maximum reliability and efciency.

Your pump is designed for use with motor oil, gear oil,

hydraulic oil and waste oil. If used with antifreeze, do not

exceed 50% water. Please take all due precautions when

handling these liquids. Your safety is important to us.

Also, to assure the longest possible service life, it is im-

portant that you follow the operation and maintenance

procedures outlined in this manual. We are proud to

provide you with a quality product and dedicated sup-

port. Together with your conscientious use, we are sure

that you will obtain years of safe, dependable service.

President

Great Plains Industries, Inc.

5252 East 36th Street North

Wichita, KS USA 67220-3205

TEL: 316-686-7361

FAX: 316-686-6746



SAVE THESE INSTRUCTIONS

Oil Pump

Models L 5016, L 5116 & L 5132

Owner’s Manual

STOP

DO NOT RETURN

THIS PRODUCT

TO THE STORE!

Please contact GPI before

returning any product. If

you are missing parts or

experience problems with

your installation, our Customer

Support Department will be

happy to assist you.

GPI Customer Support

800-835-0113 or

316-686-7361

TABLE OF CONTENTS

General Information ..................................................... 2

Safety Instructions ....................................................... 2

Installation ................................................................... 2

Operation ..................................................................... 3

Maintenance ................................................................3

Troubleshooting ........................................................... 4

Viscosity Charts ........................................................... 5

Illustrated Parts List ..................................................... 6

Specications .............................................................. 7

Service.........................................................................7

Great Plains Industries, Inc. is a member of

the Petroleum Equipment Institute.

Summary of content (8 pages)

PAGE 1
5252 East 36th Street North Wichita, KS USA 67220-3205 TEL: 316-686-7361 FAX: 316-686-6746 SAVE THESE INSTRUCTIONS Oil Pump Models L 5016, L 5116 & L 5132 Owner’s Manual STOP DO NOT RETURN THIS PRODUCT TO THE STORE! Please contact GPI before returning any product. If you are missing parts or experience problems with your installation, our Customer Support Department will be happy to assist you. GPI Customer Support 800-835-0113 or 316-686-7361 TABLE OF CONTENTS General Information....
PAGE 2
GENERAL INFORMATION The purpose of this manual is to assist you in installing, operating and maintaining your GPI Oil Pump. This pump is a positive displacement, direct drive pump. It is your responsibility to: • know and follow applicable national, state and local safety codes pertaining to installing and operating electrical equipment for use with petroleum fluids. • ensure that all equipment operators have access to adequate instructions concerning safe operating and maintenance procedures.
PAGE 3
. Screw suction pipe into inlet threads of pump base. 4. Insert the suction pipe through the tank bung. Screw pump into tank bung to secure the pump to the tank. (Figure 1) Figure 1 12-volt DC Powered Pumps (Model L 5016): This GPI Oil Pump is factory wired for 12-volt DC. Circuit must be protected with a 50 amp automotive-type fuse (not supplied). The power cord is not supplied with the pump. GPI recommends a minimum power cord of 10/3 AWG. Do not exceed 15 feet of cord.
PAGE 4
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION A. PUMP WON’T PRIME 1. Dirty strainer screen Remove and clean strainer. 2. Suction line problem Check for leaks in suction line. 3. Pump outlet is blocked or valve is shutoff Check pump outlet system for blockage. 4. Fluid level below suction pipe Refill tank or add longer suction pipe. 5. Fluid viscosity exceeds pumps rated capability Refer to the Viscosity Charts for viscosity limits. 6.
PAGE 5
VISCOSITY CHARTS 5
PAGE 6
ILLUSTRATED PARTS LIST Item No. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 6 110264-1 110264-2 110187-09 142001-01 142002-01 142021-01 142500-01 142005-01 142008-01 142009-01 142014-01 142015-01 142016-01 142022-01 142023-01 90100389 90100387 90100388 904002-24 904005-59 90400807 90400793 90400794 90400795 90600658 No. Req’d. Suction Pipe Assembly....................................... 1 Suction Pipe Assembly.......................................
PAGE 7
SPECIFICATIONS Model: L 5016 12-volt DC Pump Model: L 5116 115-volt AC 1/2 HP Model: L 5132 115-volt AC 1 HP Pump Housing: Aluminum Aluminum Aluminum Pump Rate: 16 QPM (15 LPM) 16 QPM (15 LPM) 32 QPM (30 LPM) Duty Cycle: 30 min. ON, 30 min. OFF Performance: Max. Viscosity Pumped: 390 CPS 30 min. ON, 30 min. OFF 30 min. ON, 30 min. OFF 1160 CPS 970 CPS Operating Temperature: Maximum temperature is +140° F (+60° C) (See Viscosity Chart for minimum temperature.
PAGE 8
Limited Warranty Policy Great Plains Industries, Inc. 5252 E. 36 Street North, Wichita, KS USA 67220-3205, hereby provides a limited warranty against defects in material and workmanship on all products manufactured by Great Plains Industries, Inc. This product includes a 1 year warranty from date of purchase as evidenced by the original sales receipt. A 30 month warranty from product date of manufacture will apply in cases where the original sales receipt is not available.