Manual

For Your Protection, Read Carefully
- Risk of fire. Do not install insula-
tion within 3 inches of fixture sides or wiring
compartment, nor above the fixture in such
a manner as to entrap heat.
· Turn off the power supply.
· Ground the fixture to avoid potential
electrical shocks.
· Do not handle an energized fixture or
energize any fixture with wet hands,
when standing on a wet or damp sur-
face, or in water.
· Double check all electrical connections
to be sure they are tight and correct.
· Match wattage of fixture and lamp ex-
actly.
· Do not remove or insert lamp when power
is on.
· Do not scratch glass or subject lamp to
undue pressure as either may cause
lamp breakage.
· Protect operating lamp from sources
of moisture.
Upon receipt, thoroughly inspect for any
freight damage which should be brought to
the attention of the delivery carrier. Compare
the catalog description listed on the packing
slip with the label on the carton to ensure you
have received the correct merchandise.
Figure 1
Figure 2
TRAHCGNITOOHSELBUORT
nimelborpehtetacol,noitidnocdoognimeesyehtfI.eludomni-emarfropmalehtotegamadelbisivynarofkcehC
.snoitcaevitcerrocdnasesuacelbissopfotsilgniwollofeht
motpmySesuaCelbissoPnoitcAevitcerroC
OTSLIAFPMAL
THGIL
dezigrenetonerutxifehtgnideeftiucriC·
noitcennoceludomrotiucricnirorregniriW·
pmalytluaF·
tuptuotsallabroeniL·
tsallabytluaF·
wolooterutarepmettneibmA·
.dezigrenesitiucrictahterusneotesufrorekaerbtiucrickcehC·
erasnoitcennoctahterusneotxobecilpserutxifenimaxE·
.tcerroc
ylbareferp,pmalrehtonaetutitsbusdnapmalytluafehtevomeR·
lanigiroehtecalper,sthgilpmalehtfI.thgilotnwonksitahteno
.enowenahtiw
.egatlovtiucricnepokcehC.erutxiftaegatlovenilkcehC·
.ytiunitnoctiucrickcehC·
.snoitidnoclatnemnorivnegnitsixetsniagagnitartsallabkcehC·
TUOSEOGPMAL
GNITHGILRETFA
pmalytluaF· nahtrehtarmotpmyssihttibihxelliwpmalayllanoisaccO·
.pmalwenaetutitsbuS.thgilotgniliafylpmis
NOSELCYCPMAL
FFODNA
erutxifotesolcootsinoitalusnI·
hgihootegattawpmaL·
wolegatlovtuptuotsallaB·
)"3tsaelta(eludomdnuoramorfnoitalusnievomeR·
.gnisuohnideificepsegattawpmalllatsnI·
.egatlovtiucricnepokcehC.erutxifehttaegatlovenilkcehC·
DOWNLIGHTING & TRACK SYSTEMS
ONE LITHONIA WAY, CONYERS, GEORGIA 30012, TELEPHONE [phone], FAX [phone]
www.lithonia.com IN CANADA: 1100 50TH AVE., LACHINE, QUEBEC H8T 2V3
Figure 2
1. Install rough-in section as detailed on sepa-
rate instruction sheet.
2. Determine line voltage to fixture (switched
and unswitched power requirements)
3. Verify correct ballast/lamp combination.
1. Pivot emergency ballast assembly onto mount-
ing rails of rough-in section as shown in Fig-
ure 1. Make any necessary vertical adjust-
ments to assure that the bottom of the rough-
in section is flush or slightly above (1/8" max.)
the ceiling line.
2. Make emergency ballast assembly and test
switch/pilot light connection by plugging the
two connectors together (see Figure 2).
3. Push wires and connectors into opening of
test switch/pilot light box fastened to reflec-
tor. Install flex connector into box making sure
that flex is oriented in direction of arrow (see
Figure 3).
Figure 3
Test Switch/Pilot Light Box