User manual

GMC-I Gossen-Metrawatt GmbH 3
Contents Page
Contents Page
1 Initial Inspection – Warnings . . . . . . . . . . . . . . .4
2 Initial Start-Up – Dimensional Drawings . . . . . .5
2.1 Dimensional Drawing . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Preparing for Operation . . . . . . . . . . . . . . . . . . . . . .6
2.2.1 Installing the Optional GPIB Interface Module . . . . . . . . . . . 6
2.2.2 Setup as Benchtop Device . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.3 Installation to a 19'' Device Cabinet . . . . . . . . . . . . . . . . . . 6
2.2.4 Connection to the Mains . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.5 Connecting Power Consumers . . . . . . . . . . . . . . . . . . . . . . 6
2.2.6 Connection to Computer Interfaces . . . . . . . . . . . . . . . . . . . 6
2.2.7 Connecting the Analog Interface . . . . . . . . . . . . . . . . . . . . . 7
2.3 Switching the Device On . . . . . . . . . . . . . . . . . . . . .7
3 Technical Description . . . . . . . . . . . . . . . . . . . .9
4 Technical Data . . . . . . . . . . . . . . . . . . . . . . . .12
4.1 General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.2 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.3 Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5 Controls, Display Elements and Terminals . . .16
5.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
5.2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
6 Menu Structure and Parameters . . . . . . . . . .20
7 Analog Interface . . . . . . . . . . . . . . . . . . . . . . .22
7.1 Connector pin assignments . . . . . . . . . . . . . . . . . .22
7.2 Auto-sensing mode . . . . . . . . . . . . . . . . . . . . . . . .24
7.3 Status Signal Outputs . . . . . . . . . . . . . . . . . . . . . . .24
7.4 Regulating Output Voltage . . . . . . . . . . . . . . . . . . .25
7.5 Controlling Output Current . . . . . . . . . . . . . . . . . . .25
7.6 Voltage Monitoring Output . . . . . . . . . . . . . . . . . . .26
7.7 Current Monitoring Output . . . . . . . . . . . . . . . . . . .26
7.8 Trigger Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
7.9 Parallel Connection . . . . . . . . . . . . . . . . . . . . . . . . .28
7.9.1 Direct Parallel Connection . . . . . . . . . . . . . . . . . . . . . . . . 28
7.9.2 Master-Slave Parallel Connection . . . . . . . . . . . . . . . . . . . 29
7.10 Series Connection . . . . . . . . . . . . . . . . . . . . . . . . .30
7.10.1 Direct Series Connection . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.10.2 Master-Slave Series Connection . . . . . . . . . . . . . . . . . . . . 31
7.11 Varying the Internal Output Resistance Value . . . .32
8 Descriptions of Operating Commands . . . . . .33
9 Status and Events Management . . . . . . . . . . .50
10 Table of Operating and Query Commands . . .52
10.1 Adjustable Functions and Parameters . . . . . . . . . .52
10.2 Queriable Functions and Parameters . . . . . . . . . . .54
10.3 Sequence Status Diagram . . . . . . . . . . . . . . . . . . .56
10.4 Memory Structure . . . . . . . . . . . . . . . . . . . . . . . . .57
11 System Messages . . . . . . . . . . . . . . . . . . . . .58
12 Operating Software . . . . . . . . . . . . . . . . . . . . 60
13 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
14 Order Information . . . . . . . . . . . . . . . . . . . . . 64
15 Repair and Replacement Parts Service
DKD Calibration Laboratory* and Rental
Instrument Service . . . . . . . . . . . . . . . . . . . . 64
16 Product Support . . . . . . . . . . . . . . . . . . . . . . 64