User manual

GMC-I Gossen-Metrawatt GmbH 21
1 Allows for viewing and processing of the following “condi (condition) parameters”
in setup memory n specified by “Seq-n” (application: subsequences)
2 Entry of numeric value n# is additionally possible, start address ≤ n ≤ stop address,
→ resume sequence at memory location n#
Parameters level Parameters level Parameters level Parameters level Parameters level Parameters level
Display A Display B Display A Display B Display A Display B Display A Display B Display A Display B Display A Display B
1l_l 0.0 . 00 1l_h 60 . 000
Current setting limit value, L = lower, U = upper
ovset 40 . 000
Overvoltage protection trigger value
oCset 80 . 000
Overcurrent protection trigger value
sink off C-dyn r save 01 rcl 01 t 16 14 20 2006 08 04
Footnote 4 Footnote 5 Time (hhmm) Year (YYYY) M/D (mmdd)
ddc 15
Display delay time
sig-1 off sig-2 off sig-3 off a1_v off a1_1 off
Signal input 1 on/off Signal input 2 on/off Signal input 3 on/off Voltage input on/off Current input on/off
db 8 pb none sb 1 vsb 115.2t
Number of data bits Parity bit Stop bit (1 or 2)
Footnote 2 Footnote 2
seq cont. seq stop seq Strt seq step seq bstp seq esc
Resume sequence Stop sequence Jump to start address Forward step-by-step Backwards step-by-step Exit sequence
stop 0123 rep cont. tdef 1 . 000
Stop address Repeat sequence Default time
1set 10. . 000 tset tdef fset nf
Current setpoint Dwell time Default time Function
seq_c 0105 seq_c st-sp seq_r 0101 seq_i 0108
Delete memory location 105. Delete start-stop mem. loc. Delete & shift mem. loc. Paste & shift mem. loc.
v- 9 . 998 1_ 0 . 204. 1- 0 . 212.
Max. measured voltage value Min. measured current value Max. measured current value
vc- 60 . 000 1c_ 0. . 000 1c- 60 . 000
m-cfg em_v em_1
erb 0 erC 0 Cra 1 crb 0
Events memory B Events memory C Status memory A Status memory B
1off # 1f5 #
Current setpoint zero point Current setpoint upper limit
8 9
Additional key functions:
With sequence status RUN (after GO or CONT)
[ENTER] HOLD
[ESC] Abort at actual address
[0]
Abort and jump to final value
With sequence status STOP (after Strt, Hold,
StEP or bStP)
[UP] STEP
[DOWN] BACKSTEP
[ENTER] CONT
[ESC] Abort at actual address
[0]
Abort and jump to final value
See sequence status diagram chapter 10.3
*) The sequence is also aborted at the actual
address, when turning an increment knob
or pressing a select button.
(sequence-status READY)
↵
ESC
0
U
V
↵
ESC
0
Y Z
3 Other display options can be selected while a sequence is being executed with
the
Y and Z keys:
The display does not return automatically to the standard display setting with this
option, but rather when the sequence function has been completed or aborted.
< Selected standard display setting
MEM-A 0005
Current memory location address
rrEp cont
Remaining number of repetitions
SEq-n 00
Run is part of the main sequence
FSEt __rv
Sequence function parameter
tSEt tdEF
Memory location-specific dwell time
USEt ISET For example calculated intermediate values for
a ramp function
Uout IOUt Momentary measured values
Y
Z
4The Y and Z keys can be used as follows for scrolling while a selected RCL
function is being executed (displays A and B blink until the selection is
acknowledged with the ENTER key, or until the function is otherwise aborted).
rcl 02 Access setup register 02
outp on
vset 12
. 000
1set 25
. 000
pset 1500
. . 0
oup on
ovset 80
. . 00
oCp off
oCset 80 .
. 00
pon rst
trg-1 off
trg-2 off
a1-v off
1 . off
Strt 0001
stop 0005
Y
Z
5) Display function does not
change automatically back to
standard display