User manual

26 GMC-I Messtechnik GmbH
6 Menu Structure and Parameters
* /r15 as from firmware version 004
Main menu level Submenu level Parameters level Parameters level
Display A Display B Display A Display B Display A Display B Display A Display B
setvp devic devic limit vl_l 0. 0 . 00 vl_h 60. . 000
SETUP DEVICE Limit value parameter Voltage setting limit value, L = lower, U = upper
Setup menu
devic ovp ovp on ovdly 0. 0 . 00
Overvoltage menu Overvoltage protection on/off Overvoltage delay time
devic oCp oCp off oCdly 0. 0 . 00
Overcurrent menu Overcurrent protection on/off Overcurrent delay time
devic Cfg_d pon rst sset off
Device settings after power on
setvp dpy1f dpy1f dpy dpy-a vo dpy-b 1o
SETUP DISPLAY & INTERFACE Digital display settings Display A – standard display: Uo Display B – standard display: Io
Display and interface menu
dpy1f an1f trg-1 off trg-2 off
Analog interface settings Trigger input 1 on/off Trigger input 2 on/off
dpy1f bvs addr 12 bavd 9600
Interface settings Device address
6)
(IEEE488) Transmission speed (RS232)
setvp seq seq ctrl seq go seq hold
SETUP SEQUENCE Access sequence Start sequence (RUN), footnote 3 Stop sequence
Sequence menu
seq Cond i seq-n 0 Strt 0097
Sequence settings Sequence no. (subsequence) footnote 1 Start address
seq ed it mem-a 0100 vset 39 . 000
Edit sequence Voltage setpoint
seq mem load 0105 store 0105
Memory functions Load sequence value Save as sequence value
setvp meas meas mm-v1 mm-v1 off v_ 9 . 992
SETUP MEASUREMENT EXTREME MEASUREMENT Min-Max memory Minimum measured voltage value
Measuring menu
meas v1-Cs meas v1_Cs vc_ 0 . 000
meas Cfg_m m-lp 3 m-tab
meas spec rl0ad footnote 5 30. . 531
Avx 1nfo l-Err 000 era 3
AUXILIARY Events and status memory Last error no. Events memory A
Memory and calibration menu
vers1 rel 01 . . 001 vpd no
Firmware revision Firmware version Firmware update
adjvs 7.10.11 voff # vfs #
Balancing routine Balancing date Voltage setpoint zero point Voltage setpoint upper limit


MENU











ESC

ESC

ESC

ESC

ESC

ESC

ESC

ESC

ESC

ESC
A
B
7
6
5
4
2
 
vl_h 60000
Set parameter (example: upper limit value for voltage setpoint)

vl_h 60000
 
Select entry position (decimal place).
Acknowledge selection.
vl_h 40000
 
Increase/decrease value – alternative:
vl_h 40000

Acknowledge parameter
ESC
Jump back to higher menu level.
A
ovp off
Select parameter – switch function on/off.
 Acknowledge selection.
ovp on
Select status
ovp on
 Acknowledge parameter.
B
 
(here: off, on, r01 ... r12/r15*).
Number blinks, NUM LED key lights up.
Enter value directly with the numeric keypad.
or abort procedure with
ESC
setup seq
LED display (display A / B)
Key
Parameter not yet set
 
Scroll within the parameters level.

Select submenu or parameters level.
ESC
Jump back to higher menu level.
setup seq
#
Setting value is displayed, after which the
6
Hot key for direct parameter selection
measured value is entered and acknowledged with .
Select parameters.
