Datasheet

ManualsBrandsGossen Metrawatt ManualsClamp MetersCurrent Clamp Meter, TRMS, 59.99kOhm, 19.99kHz, LCD

3-349-794-03

1/8.14

GMC-I Messtechnik GmbH

METRAClip85 and 86

Clamp Multimeters

Applications

• Measurement of starting current for electric motors

• Measurement of motor temperature rise with temperature

sensors

• Measurement of direct current, e.g. automotive batteries

Features

Display Memory (data hold)

The momentary measured value can be “frozen” at the display.

Data Logging (max., min., peak)

Measured values can be stored for long-term observation of mea-

sured quantities. At the same time, maximum, minimum and peak

values (METRAClip86 only) are acquired for the duration of the

selected recording time.

True Inrush

Measurement of motor starting current characteristics based

upon the relationship between amplitude and time.

This function makes it possible to track rapid current changes of

the damped sinusoidal oscillation type by measuring successive

TRMS values which are calculated over ½, 1, 2½, 5 and 10 peri-

ods based upon the largest calculated TRMS value, and are

refreshed via a half-wave.

Relative and Differential Measurements

A momentary measured value can be saved as a reference value.

A differential value based on the momentary measured value and

the reference value can be generated and displayed for each fol-

lowing measurement. Alternatively, the differential value can be

related to the reference value and displayed as a relative value as

a percentage for each following measurement.

Safety Devices

• Visual indication is provided in the event that the measuring

range is exceeded.

• An intermittent acoustic signal warns the user of voltages

which are equal to or larger than the safety voltage of

1000 V

DC or TRMS

Automatic Shutdown

The device is shut down automatically in the event that none of

the keys or the rotary switch are activated for a duration of 10

minutes. Automatic shutdown can be deactivated.

Applicable Regulations and Standards

IEC 61010-1/EN 61010-1/

VDE 0411-1

Safety regulations for electrical equipment for measure-

ment, control and laboratory use

IEC 61010-2-030:2010,

DIN EN 61010-2-030:2010,

VDE 0411-2-030:2011

Safety requirements for electrical equipment for measurement,

control

and laboratory use – Part 2-030: Particular re-

quirements for testing and measuring circuits

IEC 61010-2-032:2012,

DIN EN 61010-2-032:2012,

VDE 0411-2-032:2013

Part 2-032: Particular requirements for hand-held and

hand-manipulated current sensors for electrical test and

measurement

DIN EN 61326

VDE 0843, part 20

Electrical equipment for control technology and labora-

tory use – EMC requirements

• Current and frequency measurement via clamp meter:

600 A AC TRMS and 900 A DC

(automatic or manual switching)

• Multimeter functions via connector sockets:

(AC TRMS and DC) up to 1000 V voltage/frequency measurement

 Resistance and continuity test (acoustic):

Indication if a programmable threshold is fallen short of

Diode test

• Additional measurements:

Relative and differential measurements

METRAClip85:Temperature in °C/°F via type K thermocouple

Adapter function

METRAClip86: Power (W/VA/var), power factor,

THD measurement

Phase sequence (2-wire connection)

• Compact and user-friendly

One-hand operation and illuminated digital display

• Extremely safe thanks to CAT IV 600 V

Summary of content (6 pages)

PAGE 1
METRAClip85 and 86 Clamp Multimeters • • • • • Current and frequency measurement via clamp meter: 600 A AC TRMS and 900 A DC (automatic or manual switching) Multimeter functions via connector sockets: V (AC TRMS and DC) up to 1000 V voltage/frequency measurement  Resistance and continuity test (acoustic): Indication if a programmable threshold is fallen short of Diode test Additional measurements: Relative and differential measurements METRAClip85: Temperature in °C/°F via type K thermocouple Adapter
PAGE 2
METRAClip85 and 86 Clamp Multimeters Common Measuring Functions of the METRAClip85 and the METRAClip86 Measurements via Connector Sockets Measurements via Current Clamp Voltage, V DC Current. A DC Measuring Range Resolution Intrinsic Error under Reference Conditions Measuring Range 0.00  59.99 V 10 mV 0.00 V ... 5.99 V: (1.0% rdg.  10 d) 6.00 V ... 59.99 V (1.0% rdg.  3 d) 600 ... 900 A 1A (1.0% rdg. 3 d) Current, A AC (TRMS) 60.0  599.
PAGE 3
METRAClip85 and 86 Clamp Multimeters Special Measuring Functions of the METRAClip85 Apparent Power (AC, DC+AC) Measuring Range Measurements via Connector Sockets Temperature Measurement with type K Thermocouple Measuring Range 1 Resolution -60.0  599.9 °C -76.0  1111.8 °F 0.1 °C 0.1 °F +600  +1200 °C +1112  +2192 °F 1 °C 1 °F Intrinsic Error 1 under Reference Conditions 1% rdg. 3 °C 1% rdg. 5.4 °F 0.1 mV 0.60  5.99 V 10 mV 0.60  5.
PAGE 4
METRAClip85 and 86 Clamp Multimeters Common Data for the METRAClip85 and the METRAClip86 LCD with Blue Background Illumination Display 7-segment characters Number of places 4-place, 6000 digits Dimensions 222 x 78 mm Reference Conditions Ambient temperature Relative humidity Battery voltage Frequency of AC components in the signal Crest factor of measured AC signals Conductor position Neighboring conductor AC magnetic field Electrical field +23 C 2 C 45 to 75% 9.0 V 0.
PAGE 5
METRAClip85 and 86 Clamp Multimeters Order Information Description Type Article number TRMS clamp multimeter, 1000 V AC/ DC, 600 A AC, 900 A DC, frequency measurement: 20 kHz/V ...
PAGE 6
METRAClip85 and 86 Clamp Multimeters Edited in Germany • Subject to change without notice • PDF version available on the Internet GMC-I Messtechnik GmbH Südwestpark 15 90449 Nürnberg, Germany Phone: +49 911 8602-111 Fax: +49 911 8602-777 e-mail: info@gossenmetrawatt.com www.gossenmetrawatt.