Manual
Table Of Contents
- 1 Safety Instructions
- 2 Applications
- 3 Documentation
- 4 Operating Overview
- 5 Initial Startup
- 6 System Settings
- 6.1 Digital Keyboard
- 6.2 Firmware
- 6.3 Language Selection
- 6.4 Time and Date Settings
- 6.5 Digital Display Settings
- 6.6 Set Display of Leading Zeros
- 6.7 Configuring Password Protection
- 6.8 Viewing the Instrument’s Name
- 6.9 Installing a Functions Expansion
- 6.10 Switching the Instrument Off
- 6.11 Default Settings (instrument reset)
- 7 Control Functions
- 8 Measurements
- 8.1 Enabling Parameter Changes
- 8.2 Insulation Resistance Measurement – RISO Function (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE BT only)
- 8.3 Inter-Turn Short Circuit Measurement – COIL Function (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE only)
- 8.4 Absorption Index Measurement – DAR (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE BT only)
- 8.5 Polarization Index Measurement – PI (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE BT only)
- 8.6 Voltage Measurement
- 8.6.1 Alternating Voltage and Frequency Measurement V AC and Hz with Selectable Low-Pass Filter
- 8.6.2 Duty Cycle Measurement – Duty AC (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE BT only)
- 8.6.3 RPM Measurement – RPM AC (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE BT only)
- 8.6.4 Direct and Pulsating Voltage Measurement, V DC and V (AC+DC)
- 8.7 Resistance Measurement “W”
- 8.8 Capacitance Measurement F
- 8.9 Temperature Measurement with Resistance Thermometers – Temp RTD
- 8.10 Temperature Measurement with Thermocouple – Temp TC
- 8.11 Continuity Test
- 8.12 Diode Testing with Constant Current of 1 mA
- 8.13 Milliohm Measurement – Rlo (2-wire measurement) (METRAHIT IM XTRA BT and METRAHIT IM E-DRIVE only)
- 8.14 Milliohm Measurement – mW/4 (4-wire measurement)
- 8.15 Current Measurement
- 8.15.1 Direct and Pulsating Current Measurement, Direct Connection, – A DC and A (AC+DC)
- 8.15.2 Alternating Current and Frequency Measurement, Direct Connection, – AAC and Hz
- 8.15.3 Direct and Pulsating Current Measurement with Current Clamp Sensor – ADC und A (AC+DC)
- 8.15.4 Alternating Current Measurement with Current Clamp Sensor – AAC and Hz
- 8.16 Measuring Sequences – Test Sequences
- 9 Interface Operation and Software
- 10 Characteristic Values
- 11 Maintenance and Calibration
- 12 Accessories
- 13 Returns and Environmentally Sound Disposal
- 14 CE Declaration
- 15 Addresses
66 Gossen Metrawatt GmbH
12 Accessories
12.1 General
The extensive accessories available for our instruments are
checked for compliance with currently valid safety regulations at
regular intervals, and are expanded as required for new applica-
tions.
You’ll find the right product-specific and recommended universal
accessories for your instrument with all the information you need
(description, order number, etc.)
• on the Internet at www.gossenmetrawatt.com
• in the data sheet for your instrument.
12.2 Technical Data for Measurement Cables
(included with KS17-2 cable set and Z270S probe)
Electrical Safety
Observe the measuring instrument’s maximum values for electrical
safety!
Ambient Conditions (EN 61010-031)
Temp erature -20 C ... + 50 C
Relative humidity 50 ... 80%
Pollution degree
2
Use of KS17-2 and Z270S
Attention!
!
Measurements per DIN EN 61010-031 may only be per-
formed in environments in accordance with measuring
category III with the safety cap attached to the test probe
at the end of the measurement cable.
In order to establish contact inside 4 mm jacks, the safety caps
have to be removed by prying open the snap fastener with a
pointed object (e.g. the other test probe).
13 Returns and Environmentally Sound Disposal
This instrument is subject to directive 2012/19/EC on Waste Elec-
trical and Electronic Equipment (WEEE) and its German national
equivalent implemented as the Waste Electrical and Electronic
Equipment Act (ElektroG) on the marketing, return and environ-
mentally sound disposal of electrical and electronic equipment.
The device is a category 9 product (monitoring and control instru-
ment) in accordance with ElektroG (German Waste Electrical and
Electronic Equipment Act).
The symbol at the left indicates that this device and its
electronic accessories must be disposed of in accor-
dance with applicable legal regulations, and not together
with household trash. In order to dispose of the instru-
ment, bring it to a designated collection point or contact our prod-
uct support department (page 68).
This instrument is also subject to directive 2006/66/EC on batter-
ies and accumulators and waste batteries and accumulators and
its German national equivalent implemented as the Battery Act
(BattG) on the marketing, return and environmentally sound dis-
posal of batteries and accumulators.
The symbol at the left indicates that batteries and
rechargeable batteries must be disposed of in accor-
dance with applicable legal regulations. Batteries and
rechargeable batteries may not be disposed of with
household trash. In order to dispose of the batteries or recharge-
able batteries, remove them from the instrument and bring them
to a designated collection point.
Segregated disposal and recycling conserves resources and pro-
tects our health and the environment.
Current and further information is available on our website at
http://www.gossenmetrawatt.com under the search terms
“WEEE” and “environmental protection”.
Maximum rated voltage
600 V 1000 V
1000 V
Measuring category
CAT IV CAT III CAT II
Maximum rated current 1 A 1 A 16 A
With safety cap attached
—
Without safety cap
——










