User manual

GMC-I Messtechnik GmbH 49
4.14.6 Trigger Function Selection
Example: Select „Tran“ in trigger function selection (Trig Function).
For the above operating procedures, the corresponding SCPI commands should be:
TRIG:FUNC TRAN Selects transient operation (TRAN) for trigger function
4.14.7 Knob Function
Example: Enable the knob function.
4.14.8 Key Sound
Example: Enable the key sounds.
4.14.9 Communication Interface
Example 1: Select RS232 interface; set the baud rate to 9600; set parity check to None; set data bit to 8; set stop bit to 2;
enable the flow control.
Example 2: Select GPIB interface, set the address to 18.
Procedure Description Display
1 Press the key to enter into the main menu.
Load Default :
Yes *No
2
Use the ▼ key to select the menu item “Trig Function”; use the knob or the ◄ key to select the parameter “Tran”.
Press the Enter key to confirm.
Trig Function :
*Tran List
3 Press the key to exit the main menu.
0.000V 0.000A
0.000
A CCH OFF
Procedure Description Display
1 Press the key to enter into the main menu.
Load Default :
Yes *No
2
Use the ▼ key to select the menu item “Knob”; use the knob or the ◄ key to select the parameter “On”.
Press the Enter key to confirm.
Knob :
On *Off
3 Press the key to exit the main menu.
0.000V 0.000A
0.000
A CCH OFF
Procedure Description Display
1 Press the key to enter into the main menu.
Load Default :
Yes *No
2
Use the ▼ key to select the menu item “Key Sound”; use the knob or the ◄ key to select the parameter “On”.
Press the Enter key to confirm.
Key Sound :
On *Off
3 Press the key to exit the main menu.
0.000V 0.000A
0.000
A CCH OFF
Steps Description Display
Step 1 Press the key to enter into the main menu.
Load Default :
Yes *No
Step 2
Use the ▼ key to select the menu item “Interface”; use the knob or the ◄ key to select the parameter “RS232”.
Press the Enter key to confirm.
Interface :
*RS232 USB GPIB
Step 3
Use the ▼ key to select the menu item “Baud Rate”; use the knob or the ◄ key to select the parameter “9600”.
press the Enter key to confirm.
Baud Rate :
*9600 19200
Step 4
Use the ▼ key to select the menu item “Knob”; use the knob or the ◄ key to select the parameter “On”.
Press the Enter key to confirm.
Wählen Sie mit Hilfe der Taste ▼den Menüpunkt „Parity Check“. Setzen Sie mit dem Drehgeber oder der Taste ◄ den Parameter
auf „None“. Betätigen Sie die Taste Enter, um die Eingabe zu bestätigen.
Parity Check :
*None Even Odd
Step 5
Use the ▼ key to select the menu item “Data Bit”; use the knob or the ◄ key to select the parameter “8”.
Press the Enter key to confirm.
Data Bit :
*8 7
Step 6
Use the ▼ key to select the menu item “Stop Bit”; use the knob or the ◄ key to select the parameter “2”.
Press the Enter key to confirm.
Stop Bit :
1 *2
Step 7
Use the ▼ key to select the menu item “Flow Control”; use the knob or the ◄ key to select the parameter “On”.
Press the Enter key to confirm.
Flow Control :
On *Off
Step 8 Press the key to exit the main menu.
0.000V 0.000A
0.000
A CCH OFF
Steps Description Display
Step 1 Press the key to enter into the main menu.
Load Default :
Yes *No
Step 2
Use the ▼ key to select the menu item “Interface”; use the knob or the ► key to select the parameter “GPIB”.
Press the Enter key to confirm.
Interface :
RS232 USB *GPIB
Step 3
Use the ▼ key to select the menu item “GPIB Address”; use Entry keys or the knob together with ◄ ► keys to select the
parameter “18”. Press the Enter key to confirm.
GPIB-Adresse :
18
Step 4 Press the key to exit the main menu.
0.000V 0.000A
0.000
A CCH OFF