User manual

GMC-I Messtechnik GmbH 25
4.7 Operating Menu via the FUNCTION Key
The FUNCTION menu consists of the following functions for
configuring the KONSTANTER’s parameters:
Function group Function Parameter (numeric / text)
Setup
SEt OCP TP: oFF / on
Pon TP: rSt / SbY / rcL
UI
-
TP: oFF / on / rSt
rnd TP: 0 / -1 / -2
Analog Interface
AnIF trG TP: oFF / out / rcL / SEq / LLO / UI
-
Sequence Function
SEq* tSEt NP: xx.xx
tdEF NP: xx.xx
Strt NP: xxx (11 ... 252)
StoP NP: xxx (12... 253)
reP NP: xxx (cont. or 1 ... 255)
SEq** TP: Go, Strt, StoP, hold, StEP, cont.
* Sequence function: appears at left-hand display, right-hand display is blank.
** Parameter selection for sequence control: appears at left-hand display, selected parameter
appears at right-hand display.
Interface Configuration
bUS Addr NP: 0 / 1 / ... / 13 /... / 30 / (UNL)
bAUd NP: 50 / 75 / 150 / 200 / ... / 4800 /
9600 / 19200
dbit NP: 7 / 8
Pbit TP: nonE / ZEro / EVEn / odd / onE
Sbit NP: 1 / 2
NP: Numeric Parameters
Can be selected as a specified value or as a value within an
interval with corresponding resolution.
•Adjust resolution (decimal place) by pressing the <RESOL> key.
Select the value with the <> key or the <> key.
Displayed value = selected value.
TP: Text Parameters
Select parameters with the <> key or the <> key.
Acknowledge your selection by pressing the <ENTER> key.
Settings
Press the <FUNCTION> key at the front of the KONSTANTER.
If no settings have yet been changed via the FUNCTION menu
after switching the device on, the SEt function group is accessed by
pressing the <FUNCTION> key.
If settings have already been changed in the function menu, the last
edited function group or function is accessed automatically.
Accessing the last edited function:
If you want to configure a function included in the current
function group, select the function group by pressing the
<FUNCTION> key. Detailed information is included in the
respective section of this chapter.
If you want to configure a function from another function group, first
return to the
function group menu
by pressing the
<CE/LOCAL>
key.
Exit the function menu completely:
Press the <CE/LOCAL> key once again.
! Device is returned to Uout / Iout display.
Figure 4.7 a Accessing the Functions Submenu
If the function group menu is currently open, you can access
the following function groups:
If the desired function group does not appear immediately at
the left-hand display, repeatedly press the <FUNCTION> key
until the name of the desired function group appears at the
left-hand display (SEt in this example).
Forward scrolling
through function groups in this menu:
Repeatedly press the <FUNCTION> key or
Press and hold the <FUNCTION> key and repeatedly press the
<> key at the same time.
Reverse scrolling through function groups in this menu:
Press and hold the <FUNCTION> key and repeatedly press the
<> key at the same time.
Accessing functions in the selected function group:
Press the <ENTER> key.
Figure 4.7 b Switching Amongst Individual Function Groups
Note
The order in which the commands are explained in the following sections
corresponds to the actual sequence for manual operation of the SSP
KONSTANTER. This makes it easy to configure device functions and parameters
without leafing back and forth through the instructions!
FUNCTION
FUNCTION
ENTER
FUNCTION
+
Jump to
last edited
function group
Jump to
last edited
function
e.g.
e.g.
e.g.
*
CE/LOCAL
FUNCTION
FUNCTION
FUNCTION
+
FUNCTION
+
FUNCTION
+