™ playsets ™ playsets Outing with Tube Slide - Wood Roof Model: 1851EW *51-1075-W* 51-1075-W (BOXES: 1851-1, 1851-2, 1853, 1857, Slide Box & Tube Slide Box) Copyright © 2019 Gorilla Playsets All Rights Reserved 166 Etowah Industrial Court Canton, GA 30114 www.gorillaplaysets.com -NOTICE- REV: 11.20.2019 This playset is intended for residential use only. it is not intended nor warranted for either public or commercial use.
Please inspect and inventory all parts immediately upon accepting delivery. Use the inventory pages in the manual to make sure you have received all necessary parts. The quickest method to get any parts that are missing or damaged is to use our “Quick Response Center” located at: www.gorillaplaysets.com/support DO NOT RETURN THIS PRODUCT TO THE RETAILER OR CONTACT THE RETAILER DIRECTLY. THE RETAILER DOES NOT STOCK COMPONENTS. PLEASE RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE.
GORILLA PLAYSETS WARRANTY – 2019 Gorilla Playsets® (“Gorilla”) warrants its play sets to be free from defects in workmanship and materials, under normal use and conditions, for 10 years for above ground structural wood components and for one year for all other components (e.g., swings, hardware, plastics, tarps, rope ladder, etc.).
IMPORTANT SAFETY GUIDELINES This product is recommended for use by children ages 3-11. This product is intended for residential use only and not intended for use in any public setting. A safety surface such as mulch or recycled tire should be used under the play set to prevent injury from falls. Also a 6 foot safety zone should be used around the entire play set. As with any home project, good judgment and respect for power tools will greatly reduce the risk of injury.
PRODUCT REGISTRATION - OUTING WITH TUBE SLIDE - WOOD ROOF (1851EW) Gorilla Playsets ™ manufactures 3 EASY WAYS TO REGISTER the finest quality products that are designed for outstanding strength and durability. We back Complete the online registration form at: OPTION 1 http://www.gorillaplaysets.com/register our products with unparalleled warranties.
THIS PAGE INTENTIONALLY LEFT BLANK
IMPORTANT – PLEASE READ Congratulations! You have just purchase one of the finest residential wooden swing sets available today. As with any wooden product that spends its entire life outside, in varying elements, it is important to know what to expect with your new swing set so that your family can enjoy it for many years. As your swing set acclimates to its new environment, natural characteristics of the wood can show in the form of checks, or “cracks” in the lumber.
IMPORTANT DOCUMENTS CUSTOMER MUST READ AND RETAIN Please go to the following links and read important SAFETY information prior to using your new play structure. http://www.gorillaplaysets.com/Swing-Set-Safety-s/85.htm https://www.gorillaplaysets.com/Maintenance-s/129.htm http://www.gorillaplaysets.com/manuals.html (Click on your specific model) http://www.gorillaplaysets.com/Warranty-s/82.htm NOTE: Your children’s safety is our #1 concern.
Model: 1851EW (BOXES: 1851-1, 1851-2, 1853, 1857, Slide Box & Tube Slide Box) REV: 11.20.
TABLE OF CONTENTS Safety Guidelines……………………………………….......……........................................Pages 3-7 Leveling Fort, General Information and Definitions…………………................................Pages 7-9 How to Install T-nuts, and Swing Beam Loading.........................................................Pages 10-12 Site Plan, Safety Zone, Required Tool List and Kit Contents......................................Pages 13-15 Hardware, Lumber and Accessory Checklists....…………………………….................
Safety and Maintenance Tips for Your New Play Set: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children.
Safety and Maintenance Tips for Your New Play Set: (continued) Playgrounds should be inspected on a regular basis. If any of the following conditions are noted, they should be removed, corrected or repaired immediately to prevent injuries. • Hardware that is loose, worn or that has protrusions or projections. • Exposed equipment footings. • Scattered debris, litter, rocks, or tree roots. • Splinters, large cracks and decayed wood components.
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM Specification F 1292.
Play Set Surfacing Recommendations: Below are some of the recommendations that the U.S. Consumer Product Safety Commission (CPSC) offers from its Handbook for Public Playground Safety. The guide can be downloaded in full at www.cpsc.gov/PageFiles/122149/325.pdf 1. Protective Surfacing - Since almost 60% of all injuries are caused by falls to the ground, protective surfacing under and around all playground equipment is the most critical safety factor on playgrounds.
2. Fall Zones - A fall zone, covered with a protective surfacing material, is essential under and around equipment where a child might fall. This area should be free of other equipment and obstacles onto which a child might fall. Stationary climbing equipment and slides should have a fall zone extending a Minimum of 6’ in all directions from the perimeter of the equipment. Swings should have a fall zone extending a minimum of 6’ from the outer edge of the support structure on each side.
General Info to Review Before Installation • Depending on your experience, assembly of the playset can take as little as 6 hours up to 24 hours, depending on size, after inventory of parts; therefore, we recommend you set aside a full two days for assembly. • Identify all of the parts for your play set. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts.
This page is a list of definitions and explanations used throughout our instructions to aid you in the assembly of your play set. Offset Holes- Throughout the installation procedures we will refer to parts with offset holes. This refers to the orientation of the holes on the board. An offset hole is one that is closer to one side than it is the other or in other words, it is not centered on the board.
Common Installation Practice Installing T-nuts When installing T-nuts into the wood, use a smooth faced hammer to set the face of the T-nut flush into the wood. Corner Post T-nut This picture shows the T-nut inserted and installed flush to the wood. Flush (Correct) Insert the barrel of the T-nut into the predrilled hole. Using a smooth faced hammer, drive the T-nut until the face of the T-nut is flush to the wood. This picture shows an end view of the T-nut installed flush to the wood.
HOW A T-NUT WORKS USUALLY THE FIRST STEP IN OUR ASSEMBLY INSTRUCTIONS IS TO INSERT T-NUTS INTO THE CORNER POSTS. A T-NUT IS A FASTENER WHICH IS THREADED ON THE INSIDE AND IT FUNCTIONS JUST LIKE A STANDARD HEX NUT. YOU INSERT THE T-NUTS INTO THE PREDRILLED HOLES IN THE CORNER POSTS. THE T-NUT HAS A BARREL SHAPED END WHICH GOES INTO THE HOLE IN THE CORNER POST. THE T-NUT ALSO HAS A FLANGE SHAPED END WITH TEETH.
SWING BEAM LOADING Weight Limits for Accessories: The weight limit for a Swing Belt is 225 lbs. (Although 150lbs is the maximum recommended swinging weight capacity for the swing position.) The weight limit for a Trapeze Bar is 125 lbs. Maximum Allowable swinging weight for a three position swing: 1) The maximum allowable swinging weight at each Swing Belt position is 150 lbs. 2) The maximum allowable swinging weight at the Trapeze position is 125 lbs. 3) The MAXIMUM SWING BEAM LOAD IS 425 lbs.
Outing 1851EW Overhead with Dimensions Please familiarize with the manual, parts/components and general Fall Height: 75" (with 6"yourself of safety surfacing in place) Playset height: 9' - 6-1/8" construction process of your new playset before getting started.
SAFETY ZONE - 1851EW MORE TEXT SAFETY ZONE 15 26'-9 16 " 6'-0" 12'-6" 6'-0" 1 27'-4 8 " 6'-0" 12'-6" 6'-0" 6'-0" 6'-0" 6'-0" (6) foot unobstructed safety perimeter around playset recommended 14
REQUIRED TOOL LIST: ___ Standard or Cordless Drill w/ Phillips Bit (#2 square bit provided) ___ Drill Bits 1/8”, 3/16”, 3/8”.
11-0104 #8 X 1" 1851 HARDWARE WOOD SCREW PAGE 1 OF 3 QTY: 8 REV A: 9/23/2019 JH #8 X 1-1/4" WOOD SCREW QTY: 48 1700Z 1325Z #8 X 1-1/2" WOOD SCREW QTY: 40 9 1701Z #8 X 2" WOOD SCREW QTY: 100 8 1342Z #8 X 2-1/2" WOOD SCREW QTY: 54 1327Z 7 #8 X 3" WOOD SCREW QTY: 10 1077Z 6 #14 X 2-1/2" PAN HEAD WOOD SCREW QTY: 2 1329Z #14 X 1-1/4" TRUSS HEAD WOOD SCREW QTY: 6 1/4" SPLIT LOCK WASHER QTY: 2 1341Z 5/16" SPLIT LOCK WASHER QTY: 32 1332Z FS2897 4 #2 SQUARE DRIVE BIT QTY: 1 FS2824 3 5/16 T-NUT QT
1478Z NOTE: CARRIAGE BOLTS OVER 6" MAY BE UP TO 1/4" SHORTER DUE TO MANUFACTURER TOLERANCES.
11-0104 1851 HARDWARE PAGE 3 OF 3 REV A: 9/23/2019 JH NOTE: HEX BOLTS MAY COME PARTIALLY OR FULLY THREADED DEPENDING UPON THE MANUFACTURER. 9 1" 5/16" X 1" HEX BOLT QTY: 2 1702Z 5/16" X 1-1/2" HEX BOLT QTY: 4 8 1703Z 5/16" X 1-3/4" HEX BOLT QTY: 2 7 6 1706Z 5 5/16" X 3-1/2" HEX BOLT QTY: 12 1715Z 4 5/16" x 3-3/4" HEX BOLT QTY: 8 1705Z 3 FS 2837 2 3/8" BOLT COVER QTY: 20 1 USE THE RULER TO THE RIGHT TO MEASURE YOUR BOLTS AND SCREWS.
11-0106 #8 X 3/4" 1853 HARDWARE WOOD SCREW PAGE 1 OF 1 QTY: 44 REV A: 9/20/2019 JH #8 X 1" WOOD SCREW QTY: 40 #8 X 1-1/4" WOOD SCREW QTY: 200 1725Z 1700Z 9 1325Z #8 X 1-1/2" WOOD SCREW QTY: 64 8 1701Z #8 X 2" WOOD SCREW QTY: 24 1342Z 7 #8 X 2-1/2" WOOD SCREW QTY: 2 1327Z 6 5 4" 5/16" x 4" HEX BOLT QTY: 4 1713Z 4 NOTE: HEX BOLTS MAY COME PARTIALLY OR FULLY THREADED DEPENDING UPON THE MANUFACTURER.
11-0109 1857 HARDWARE PAGE 1 OF 1 REV A: 9/20/2019 JH #8 X 1-1/4" WOOD SCREW QTY: 10 1325Z #8 X 1-1/2" WOOD SCREW QTY: 3 1701Z #8 X 2" WOOD SCREW QTY: 14 3/8 X 1-1/8"L BLACK PLASTIC PLUG QTY: 3 9 8 1342Z #8 X 2-1/2" WOOD SCREW QTY: 36 1327Z 7 #8 X 3" WOOD SCREW QTY: 4 1077Z 6 5 4" 5/16" X 4" HEX BOLT QTY: 2 1713Z NOTE: HEX BOLTS MAY COME PARTIALLY OR FULLY THREADED DEPENDING UPON THE MANUFACTURER.
1851EW PICTURE DESCRIPTION WAVE SLIDE QTY.
PICTURE DESCRIPTION QTY.
PICTURE DESCRIPTION QTY.
PICTURE DESCRIPTION QTY.
1851 STAMPED ID & DESCRIPTION PICTURE HINT! R FO LOOK P STAM T R ON PA 1851A LADDER BACK 5/8" X 3-3/8" X 18-1/2" 1851B PANEL SLAT 3/4" X 2-5/8" X 24-1/2" 1851D DECK SPACER QTY.
PICTURE STAMPED ID & DESCRIPTION QTY.
PICTURE STAMPED ID & DESCRIPTION QTY.
PICTURE STAMPED ID & DESCRIPTION 1851AA CROSS MEMBER 1" X 3-3/8" X 68-1/2" 1851AC LADDER SIDE L/H 1-3/8" X 3-3/8" X 53" 1851AD LADDER SIDE R/H 1-3/8" X 3-3/8" X 53" 1851AE ROCK WALL SIDE SUPPORT 1-3/8" X 3-3/8" X 56" 1851AF SWING BEAM MOUNT 3" X 3" X 44" 1851AG SWING LEG 3" X 3" X 95" 1851AH CORNER POST 1 3" X 3" X 95" QTY.
PICTURE STAMPED ID & DESCRIPTION QTY.
1853 PICTURE DESCRIPTION 1853A ROOF BOARD 1/2" X 3-5/16" X 48" 1853B WINDOW SUPPORT BATTEN QTY.
PICTURE DESCRIPTION QTY.
1857 PICTURE DESCRIPTION QTY.
PICTURE DESCRIPTION 1857H FOOTER 4 1-3/8" X 3-3/8" X 18" 1857I VERTICAL FILLER 1-3/8" X 3-3/8" X 28-5/8" 1857J TOP PANEL BOARD QTY.
STEP 1: SWING BEAM MOUNT 1: PLACE THE TORQUE WASHERS OVER THE END OF THE CARRIAGE BOLTS AS SHOWN WITH THE TEETH FACING AWAY FROM THE HEAD OF THE BOLT. HAMMER THE HEAD OF THE BOLT TO SET THE TEETH INTO THE CORNER POSTS. 2: FASTEN THE SWING BEAM MOUNT WITH WASHERS AND LOCK NUTS.
STEP 2: SWING BEAM PLATE 1: INSTALL THE SWING BEAM PLATE WITH THE POINTED END FACING AS SHOWN.
STEP 3: END SANDBOX BOARD 1: INSTALL T-NUTS AND THEN FASTEN THE END SANDBOX BOARD AS SHOWN BELOW. THE COUNTERBORED HOLES FACE OUT.
STEP 4: DECK SUPPORT 1: INSTALL T-NUTS AND THEN FASTEN THE DECK SUPPORT AS SHOWN BELOW. THE COUNTERBORED HOLES SHOULD BE ON THE BOTTOM AND SHOULD FACE OUT.
STEP 5: ROCK WALL SIDE TOP PANEL BOARD 1: INSTALL T-NUTS AND THEN FASTEN THE ROCK WALL SIDE TOP PANEL BOARD AS SHOWN BELOW. THE COUNTERBORED HOLES SHOULD FACE OUT.
STEP 6: END SANDBOX BOARD 1: INSTALL T-NUTS AND THEN FASTEN THE END SANDBOX BOARD AS SHOWN BELOW. THE COUNTERBORED HOLES SHOULD BE AT THE TOP FACING OUT.
STEP 7: DECK SUPPORT 1: INSTALL T-NUTS AND THEN FASTEN THE DECK SUPPORT AS SHOWN BELOW. THE COUNTERBORED HOLES SHOULD BE ON THE BOTTOM AND SHOULD FACE OUT.
STEP 8: T-NUTS 1: INSTALL T-NUTS AS SHOWN BELOW ON THE INSIDE FACE OF EACH CORNER POST. 14 T-NUTS WILL BE USED.
STEP 9: PANEL SUPPORT 1: FASTEN THE PANEL SUPPORT TO THE FRONT AS SHOWN. THE COUNTERBORED HOLES SHOULD BE ON THE TOP AND SHOULD FACE OUT.
STEP 10: ARCH BOARD 1: FASTEN THE ARCH BOARD TO THE FRONT AS SHOWN. THE COUNTERBORED HOLES SHOULD BE ON THE BOTTOM AND SHOULD FACE OUT.
STEP 11: SIDE SANDBOX BOARD R/H 1: FASTEN THE SIDE SANDBOX BOARD R/H TO THE FRONT AS SHOWN. THE COUNTERBORED HOLES SHOULD BE ON THE BOTTOM AND SHOULD FACE OUT.
STEP 12: SIDE SANDBOX BOARD L/H 1: FASTEN THE SIDE SANDBOX BOARD L/H TO THE REAR AS SHOWN. THE COUNTERBORED HOLES SHOULD BE ON THE BOTTOM AND SHOULD FACE OUT.
STEP 13: BOTTOM PANEL BOARD 1: FASTEN THE BOTTOM PANEL BOARD TO THE REAR AS SHOWN.
STEP 14: FORT SIDE SUPPORTS 1: INSTALL A T-NUT INTO EACH FORT SIDE SUPPORT AND THEN FASTEN EACH SUPPORT AS SHOWN. USE A SPEED SQUARE TO ENSURE THE SANDBOX BOARD IS SQUARE TO THE CORNER POSTS PRIOR TO ATTACHING THE FORT SIDE SUPPORTS. CORNER POST FORT SIDE SUPPORT SPEED SQUARE 90.
STEP 15: LEVELING THE PLAY SET AND ADDING SCREWS 1: LEVEL AND SQUARE THE BOARDS AT THE DECK LEVEL FIRST. THEN INSTALL SCREWS. 2: LEVEL AND SQUARE THE REMAINDER OF THE BOARDS AND THEN INSTALL SCREWS.
STEP 16: ROCK WALL SIDE SUPPORTS 1: INSTALL A T-NUT INTO EACH ROCK WALL SIDE SUPPORT AND THEN FASTEN EACH SUPPORT AS SHOWN.
STEP 17: PANEL SUPPORTS 1: MAKE A MARK ON EACH CORNER POST AT THE DIMENSIONS SHOWN. 2: PLACE THE BOTTOM OF EACH PANEL SUPPORT ON THE MARK AND FASTEN AS SHOWN.
STEP 18: LADDER ASSEMBLY 1: INSTALL A T-NUT INTO EACH OF THE LADDER SIDES. 2: PLACE ONE OF THE LADDER SIDES ON THE GROUND WITH THE CHANNELS FACING UP. 3: INSERT THE LADDER STEPS INTO THE CHANNELS AND PLACE THE SECOND LADDER SIDE ON TOP. 4: FLUSH THE FRONT CORNER OF EACH STEP TO THE FRONT OF THE LADDER SIDE. THEN FASTEN THE STEP TO THE LADDER SIDE WITH TWO SCREWS. REPEAT FOR THE OTHER STEPS. 5: FLIP THE LADDER OVER AND REPEAT SUBSTEP 4 FOR THE OTHER SIDE.
STEP 19: ATTACHING THE LADDER 1: FLUSH THE RIGHT SIDE OF THE LADDER TO THE INSIDE OF THE CORNER POST. 2: MAKE THE BOTTOM OF EACH 90 BRACKET 3/4" ABOVE THE BOTTOM OF THE BOARD. 3: MARK THROUGH THE HOLES IN THE BRACKETS ONTO THE BOARD. 4: DRILL 3/8" HOLES WHERE MARKED. 5/16" Washer 5: INSTALL T-NUTS INTO THE BACK OF THE BOARD. T-Nut 5/16" Lock Washer 6: FASTEN THE BRACKETS AS SHOWN.
STEP 20: DECK BOARDS 1: LAY THE DECK BOARDS AND DECK SPACERS ACROSS THE DECK SUPPORTS AS SHOWN. NOTE THE TWO HOLES AT THE CENTER OF THE DECK SPACER WILL FACE OUT. 2: FASTEN THE DECK SPACERS WITH ONE SCREW ON EACH END. FASTEN THE DECK BOARDS WITH TWO SCREWS ON EACH END.
STEP 21: TOP PANEL BOARD (REAR) 1: PLACE THE VERTICAL FILLER BOARDS ON TOP OF THE BOTTOM PANEL BOARD. 2: PLACE THE TOP PANEL BOARD ON TOP OF THE VERTICAL FILLER BOARDS. 3: FASTEN THE TOP PANEL BOARD AS SHOWN. 4: REMOVE THE VERTICAL FILLER BOARDS.
STEP 22: CENTER POSTS 1: CENTER THE CENTER POST BETWEEN THE CORNER POSTS ON THE INSIDE OF THE ARCHED BOARD. MAKE SURE THE OUTSIDE FACE OF THE CENTER POST IS FLUSH TO THE OUTSIDE FACE OF THE CORNER POSTS. THE BOTTOM OF THE CENTER POST MUST BE IN CONTACT WITH THE DECK SPACER PRIOR TO INSTALLING SCREWS THROUGH THE DECK SPACER. INSTALL SCREWS AS SHOWN. 2: PLACE THE VERTICAL POST AS SHOWN RESTING ON TOP OF THE DECK SPACER. INSTALL SCREWS AS SHOWN.
STEP 23: DECK STRINGER 1: CENTER THE DECK STRINGER UNDER THE DECK BOARDS AS SHOWN. 2: INSTALL THE 1-1/2" WOOD SCREWS FIRST, THEN THE 2" AND 2-1/2" WOOD SCREWS.
STEP 24: FILLER BOARDS 1: PLACE THE VERTICAL FILLER AGAINST THE CORNER POST FLUSH TO THE OUTSIDE AS SHOWN. FASTEN AS SHOWN. 2: PLACE THE VERTICAL FILLER AGAINST THE VERTICAL POST FLUSH ON BOTH SIDES. FASTEN AS SHOWN. 3: PLACE A BLACK PLASTIC PLUG INTO THE THREE OPEN HOLES IN THE REAR CORNER POSTS AS SHOWN.
STEP 25: PANEL/WALL SLATS 1: PLACE PANEL SLATS ON THE INSIDE OF THE PANEL SUPPORT BOARDS. THE TOP OF EACH PANEL SLAT SHOULD BE FLUSH TO THE TOP OF THE PANEL SUPPORT. 2: SPACE THE PANEL SLATS AS SHOWN BELOW AND FASTEN AS SHOWN. REAR SLAT SPACING (VIEW FROM REAR OF PLAY SET) #8 x 1-1/4" Wood Screws Slats Flush at top.
STEP 26: ROOF SUPPORTS 1: LAY THE ROOF SUPPORTS DOWN ON A FLAT SURFACE WITH THE COUNTERBORED HOLES FACING DOWN. ALIGN THE ANGLED ENDS OF THE ROOF SUPPORTS FLUSH WITH ONE ANOTHER. 2: PLACE A ROOF PEAK SUPPORT ON TOP OF THE ROOF SUPPORTS AS SHOWN. THE EDGES SHOULD BE FLUSH WHERE SHOWN BELOW. 3. CHECK THAT THE HOLES ARE 42-1/2" CENTER TO CENTER AS SHOWN BELOW. 4: FASTEN THE ROOF PEAK SUPPORT AS SHOWN. 5: REPEAT SUBSTEPS 1-4 TO MAKE ANOTHER ROOF SUPPORT ASSEMBLY.
STEP 27: INSTALLING ROOF SUPPORT ASSEMBLIES 1: PLACE THE ROOF SUPPORT ASSEMBLIES ON THE OUTSIDE OF THE CORNER POSTS AS SHOWN WITH THE COUNTERBORED HOLES FACING OUT. 2: FASTEN EACH ROOF SUPPORT ASSEMBLY AS SHOWN.
STEP 28: SWING BEAM AND SWING HANGERS 1: LINE UP THE HOLES IN THE SWING HANGERS WITH THE HOLES IN THE SWING BEAM. 2: FASTEN EACH HANGER WITH THE FASTENERS AS SHOWN.
STEP 29: SWING BEAM - ANGLED PLATES 1: INSTALL BRACKETS TO SWING LEGS AS SHOWN. 2: DO NOT TIGHTEN HARDWARE AT THIS POINT. A 1851AG SWING LEG THESE SHOULD BE PARALLEL AFTER FASTENING THEM.
STEP 30: SWING BEAM - LEGS 1: INSTALL BEAM 90 PLATE AS SHOWN. 2: ATTACH CROSS MEMBER AS SHOWN. HINT: USE HAMMER TO INSTALL T-NUTS.
STEP 31: SWING BEAM TO SWING BEAM LEGS 1: CAREFULLY PLACE THE SWING BEAM BETWEEN THE SWING BEAM BRACKETS (LEFT AND RIGHT) AS SHOWN IN THE DIAGRAM BELOW. SWING BEAM BRACKETS (LEFT AND RIGHT) SWING BEAM SWING BEAM AND LEGS UP 2: ASSEMBLE WITH FASTENERS AS SHOWN **DO NOT FULLY TIGHTEN FASTENERS AT THIS POINT.
STEP 32: SWING BEAM TO SWING BEAM LEGS 1: FASTEN THE SWING BEAM TO THE 2499 BRACKET WITH THE HARDWARE SHOWN.
STEP 33: SWING BEAM - SCREWS 1: TIGHTEN UP ALL OF THE BOLTS AT THIS TIME. 2: INSTALL SCREWS AS SHOWN BELOW.
STEP 34: SWING BEAM - ATTACH TO PLAY SET 1: PLACE SWING BEAM ON SWING BEAM PLATE AND ATTACH AS SHOWN. HINT: USE HAMMER TO TAP BOLT TO SEAT THE TORQUE WASHER.
STEP 35: ROOF BOARDS 1: PLACE THE ROOF BOARDS NEAR THE PEAK FLUSH TO ONE ANOTHER. 2: OBSERVE THE OVERHANG DIMENSIONS BELOW BEFORE FASTENING THE ROOF BOARDS. FASTEN ROOF BOARDS AS SHOWN. INSTALL 3 ROOF BOARDS PER SIDE. OTHERS WILL BE INSTALLED LATER.
STEP 36: ROOF STRINGERS 1: CENTER THE ROOF STRINGERS UNDER THE MIDDLE HOLE IN THE ROOF BOARDS. 2: FASTEN AS SHOWN. #8 x 1" Wood Screw 1853H ROOF STRINGER FLUSH ROOF STRINGER EQUAL DISTANCE EQUAL DISTANCE BOTTOM EDGE OF ROOF STRINGER ENDS SHOULD BE FLUSH TO EACH OTHER.
STEP 37: ROOF BOARDS 1: OBSERVE THE OVERHANG DIMENSIONS BELOW BEFORE FASTENING THE ROOF BOARDS. 2: FASTEN SEVEN MORE ROOF BOARDS ON EACH SIDE OF THE ROOF. THE BOTTOM TWO ROOF BOARDS ARE LEFT OFF FOR NOW SO THAT THE SIDE WALLS MAY BE ADDED NEXT.
STEP 38: WINDOW TOP PANEL BOARDS 1: PLACE EACH WINDOW TOP PANEL BOARD WITH THE BEVEL SIDE UP AT THE DIMENSIONS SHOWN. 2: FASTEN EACH WINDOW TOP PANEL BOARD AS SHOWN.
STEP 39: WINDOW CENTER FILLER/VERTICAL SUPPORT 1: MAKE MARKS ONTO THE INSIDE OF THE BOARDS AT 7/16" AND 13-5/16". PLACE THE TOP OF THE WINDOW CENTER FILLER DOWN 7/16" FROM THE TOP OF THE WINDOW TOP PANEL BOARD AND FASTEN. 2: PLACE THE BOTTOM OF THE WINDOW CENTER FILLER DOWN 13-5/16" FROM THE TOP OF THE WINDOW TOP PANEL BOARD AND FASTEN. 3: LINE UP THE TOP END OF THE WINDOW VERTICAL SUPPORTS WITH THE TOP OF THE UPPER WINDOW CENTER FILLER BOARDS.
STEP 40: SIDE WINDOWS 1: CENTER EACH WINDOW OVER THE OPENING AND FASTEN AS SHOWN.
STEP 41: ROOF BOARDS 1: OBSERVE THE OVERHANG DIMENSIONS BELOW BEFORE FASTENING THE ROOF BOARDS. 2: FASTEN TWO MORE ROOF BOARDS ON EACH SIDE OF THE ROOF.
STEP 42: SUNBURST SUPPORT 1: PLACE THE SUNBURST SUPPORT DIRECTLY UNDERNEATH THE ROOF SUPPORTS AS SHOWN. 2: THE FACE OF THE SUNBURST SUPPORT MUST BE FLUSH TO THE FRONT FACE OF BOTH ROOF SUPPORTS. MAKE THE SUNBURST SUPPORT PARALLEL TO THE ARCH BOARD UNDER IT. 3: INSTALL HARDWARE AS SHOWN.
STEP 43: FRONT WALL BOARDS 1: DRAW A LINE 1-3/4" DOWN FROM THE TOP OF THE ARCH BOARD ON THE INSIDE. ALIGN THE BOTTOM OF THE BOARDS WITH THIS LINE. 2: CENTER THE MIDDLE VERTICAL WINDOW SUPPORT 2 AND THEN FASTEN IT. 3: USE DIAGRAM SHOWN TO SPACE THE BOARDS. THE SHORTEST BOARDS HAVE 1/4" SPACING BETWEEN THEM. 4: FASTEN ALL BOARDS AS SHOWN.
STEP 44: WINDOW SUPPORT BATTENS 1: CENTER A WINDOW SUPPORT BATTEN AT THE TOP AND BOTTOM OF THE OPENINGS. THE BOTTOM OF THE TOP BATTENS SHOULD BE FLUSH TO THE BOTTOM END OF THE VERTICAL WINDOW SUPPORT 3 BOARDS. THE TOP OF THE BOTTOM BATTENS SHOULD BE FLUSH TO THE TOP END OF THE VERTICAL WINDOW SUPPORT 3 BOARDS. 2: FASTEN EACH BATTEN AS SHOWN.
STEP 45: FRONT WALL WINDOWS 1: PLACE THE BOTTOM OF EACH WINDOW 2-1/2" OFF THE TOP OF THE ARCH BOARD. CENTER THE WINDOW SIDE TO SIDE IN THE OPENING. 2: FASTEN THE WINDOW AS SHOWN. REPEAT FOR THE SECOND WINDOW.
STEP 46: SUNBURSTS 1: PLACE A SUNBURST AGAINST THE ROOF SUPPORTS UNDER THE ROOF OVERHANG. 2: SECURE THE SUNBURST AS SHOWN. 3: REPEAT SUBSTEPS 1 & 2 ON THE OPPOSITE SIDE OF THE ROOF.
STEP 47: ROCK WALL ROCKS 1: LAY OUT THE ROCK WALL BOARDS ON THE GROUND IN A PATTERN AS SHOWN. 2: FASTEN EACH ROCK TO THE ROCK WALL BOARD WITH THE FASTENERS INCLUDED IN THE ROCK BAG.
STEP 48: ROCK WALL BOARDS AND STRINGER 1: MEASURE DOWN 3/4" ON THE BACK SIDE OF THE TOP ROCK WALL BOARD AND MAKE A MARK. 2: PLACE THE TOP OF THE ROCK WALL STRINGER ON THE MARK AND FASTEN IT AS SHOWN. 3: PLACE THE TOP ROCK WALL BOARD INTO POSITION FLUSH AGAINST THE CORNER POSTS. SECURE IT TO THE ROCK WALL SIDES WITH THE 2" SCREWS AS SHOWN. 4: CONTINUE DOWN THE ROCK WALL INSTALLING ALL OF THE ROCK WALL BOARDS IN THE PATTERN SHOWN.
STEP 49: SLIDE BLOCK 1: MEASURE TO DRILL THE HOLES AS SHOWN AND MAKE MARKS. 2: DRILL 1/8" HOLES AT THE MARKS AND INSTALL THE SLIDE BLOCK. #8 x 1-1/2" Wood Screws DRILL THROUGH TWO 1/8" HOLES FOR SCREWS 10" 1 24" 1 44" 1851P SLIDE BLOCK 1851P SLIDE BLOCK NOTE: TWO SLIDE BLOCKS ARE INCLUDED BUT ONLY ONE IS USED FOR THIS PLAYSET.
STEP 50: SLIDE 1: PLACE THE SLIDE MOUNTING TAB BACK 3-9/16" FROM THE FRONT BOARD ON THE PLAY SET. 2: CENTER THE SLIDE IN THE OPENING. 3: PRE-DRILL 1/8" HOLES AT THE INDENTATIONS IN THE SLIDE INTO THE DECK SPACER 1" DEEP. 4: SECURE THE SLIDE TO THE DECK SPACER WITH #14 X 1-1/4" TRUSS HEAD SCREWS. **DO NOT OVERTIGHTEN SCREWS** #14 x 1-1/4" Truss Head Screws **DO NOT OVERTIGHTEN** DECK SPACER FRONT BOARD 9 3 16 " SLIDE **ONCE SLIDE IS INSTALLED DO NOT LIFT THE BOTTOM END OR DAMAGE COULD OCCUR.
STEP 51: HANGING THE SWINGS 1: PLACE EACH OF THE SWING CHAINS ONTO THE HOOK OF THE SWING HANGERS. PLACE CHAINS ONTO HIGHER OR LOWER LINKS TO ADJUST THE HEIGHT OF THE SWING. 2: REPEAT THIS PROCESS FOR THE TRAPEZE SWING.
STEP 52: CLIMBING ROPE 1: THREAD THE ROPE AS SHOWN IN THE DIAGRAM BELOW. TIE A FIGURE 8 KNOT BEHIND THIS HOLE ADD UP TO THREE THUMB KNOTS TO AID IN CLIMBING. TIE THUMB KNOTS BEHIND THIS HOLE UNTIL ALL OF THE ROPE IS USED. FOR SAFETY, ENSURE THAT THE ROPE IS TIGHT ENOUGH SO THAT IT CANNOT BE LOOPED BACK ON ITSELF. KEEP TYING THUMB KNOTS AT THE BOTTOM END OF THE ROPE UNTIL THERE IS NO REMAINING LOOSE ROPE. DO NOT CUT ENDS OF ROPE.
STEP 53: FLAG KITS 1: INSTALL THE FLAG KITS ON THE ROOF SUPPORTS AT THE FRONT OF THE FORT. THE BASE OF THE FLAG WILL COVER UP THE BOLTS THAT ATTACH THE ROOF SUPPORTS TO THE CORNER POSTS. 2: ATTACH THE FLAG KITS WITH THE HARDWARE PROVIDED.
STEP 54: STEERING WHEEL 1: DRILL A 3/16" HOLE BY 1" DEEP INTO THE REAR CENTER POST AS SHOWN. 2: PLACE THE SPACER INSIDE THE STEERING WHEEL. 3: SECURE THE STEERING WHEEL TO THE REAR CENTER POST WITH THE WASHER AND THE LAG SCREW PROVIDED. DO NOT OVER-TIGHTEN! 4: SNAP THE STEERING WHEEL CAP INTO THE HUB OF THE STEERING WHEEL. DRILL HOLE HERE SPACER WASHER LAG SCREW STEERING WHEEL CAP STEERING WHEEL DETAIL B B 1 12" 11 1 16 " REAR CENTER POST Drill 3/16" hole by 1" deep.
STEP 55: TELESCOPE 1: MAKE A MARK CENTERED ON THE RAILING 4" FROM THE INSIDE OF THE CORNER POST. 2: CENTER THE TELESCOPE BASE OVER THE MARK AND FASTEN WITH THE SCREW PROVIDED. 3: SNAP THE ENDS OF THE BASE INTO THE SOCKETS ON THE SIDES OF THE TELESCOPE.
STEP 56: SAFETY HANDLES 1: PLACE THE SAFETY HANDLES AS SHOWN. ATTACH THEM WITH THE HARDWARE THAT IS INCLUDED WITH THEM.
STEP 57: GROUND STAKES 1: HAMMER A GROUND STAKE INTO THE EARTH NEXT TO EACH SWING LEG AT AN ANGLE. DO NOT HOLD THE UPPER PORTION OF THE STAKE. 2: ATTACH TO THE SWING LEG WITH THE HARDWARE PROVIDED WITH THE GROUND STAKE. 3: HAMMER A GROUND STAKE INTO THE EARTH NEXT TO EACH CORNER POST NEAR THE ROCK WALL SIDE. DO NOT HOLD THE UPPER PORTION OF THE STAKE. 4: ATTACH TO THE SWING LEG WITH THE HARDWARE PROVIDED WITH THE GROUND STAKE.
STEP 58: NAME PLATE/SAFETY WARNING PLATE 1: ATTACH THE ALUMINUM NAME PLATE CENTERED ON THE FRONT OF THE SWING BEAM WITH #8 X 1-1/4" WOOD SCREWS. 2: ATTACH SAFETY WARNING PLATE AS INDICATED WITH SCREWS INCLUDED WITH PLATE. PLACE NAME PLATE HERE AND SECURE WITH #8 X 1-1/4" WOOD SCREWS. SAFETY WARNING PLATE (AIign bottom of plate with bottom of board and secure with screws included with plate.
STEP 59: BOLT CAPS 1: IF A BOLT CAP MAY BE INSTALLED ONTO BOLT END AND IS NOT EASILY REMOVED THEN DO SO. IF IT IS EASILY REMOVED THEN DO NOT INSTALL.
PART 2 TUBE SLIDE 93
SA 1522 Tube Slide Hardware REVA: 11-14-2019 JH 9 5/16" x 2-1/2" LAG SCREW QTY: 4 8 5/16" x 1-1/2" LAG SCREW QTY: 10 5/16" x 1" HEX BOLT QTY: 5 5/16" x 3/4" HEX BOLT QTY: 45 7 6 5 4 5/16" WASHER QTY: 114 3 5/16" LOCK NUT QTY: 51 2 NOTE: OTHER FASTENERS ARE INCLUDED IN THIS HARDWARE KIT BUT THEY ARE NOT REQUIRED TO BUILD THIS PLAYSET. 1 USE THE RULER TO THE RIGHT TO MEASURE YOUR BOLTS AND SCREWS. PICTURE VIEWS SHOWN ABOVE ARE 1:1 SCALE AND CAN BE USED TO MATCH BOLT AND SCREW SIZES.
PICTURE DESCRIPTION QTY.
STEP 1: TUBE SLIDE 1: FASTEN THE ENTRANCE SECTION LEFT/RIGHT PIECES TOGETHER AS SHOWN.
STEP 2: TUBE SLIDE FASTEN ELBOW SECTIONS TOGETHER AS SHOWN.
STEP 3: TUBE SLIDE 1: ALIGN THE FLANGE OF EACH SECTION WITH ONE ANOTHER. 2: ROTATE THE ELBOW SECTION CLOCKWISE TWO HOLES. 3: FASTEN THE SECTIONS TOGETHER AS SHOWN.
STEP 4: TUBE SLIDE 1: MAKE SURE THE "T" IS LOCATED AT THE TOP OF THE ENTRANCE PANEL ON THE OUTSIDE BEFORE SECURING. 2: FASTEN THE ENTRANCE PANEL TO THE ENTRANCE SECTION AT THE FOUR LOCATIONS SHOWN.
STEP 5: TUBE SLIDE 1: ALIGN THE SLIDE BASE (FOOTER) TO THE ELBOW SECTION WITH ONE HOLE EXPOSED. 2: FASTEN THE SLIDE BASE (FOOTER) TO THE ELBOW SECTION AS SHOWN AT THREE LOCATIONS.
STEP 6: TUBE SLIDE 1: REFER TO THE BOTTOM RIGHT IMAGE FOR SLIDE LOCATION. HAVE AN ASSISTANT HELP PLACE AND HOLD THE SLIDE WHILE YOU INSTALL THE LAG SCREWS. 2: REFER TO THE TOP RIGHT IMAGE FOR THE FASTENERS. THE SAME FASTENERS ARE USED ON THE OTHER SIDE AS WELL. ALSO SEE DIAGRAM AT MIDDLE LEFT.
STEP 7: TUBE SLIDE 1: MARK OUT A POSITION FOR THE GROUND STAKE ON THE INSIDE OF THE SLIDE BASE (FOOTER). 2: REMOVE THE SLIDE BASE (FOOTER). THEN HAMMER IN THE GROUND STAKE UNTIL 2" REMAINS ABOVE THE GROUND. 3: RE-INSTALL THE SLIDE BASE (FOOTER) ONTO THE ELBOW. 4: FASTEN THE SLIDE BASE (FOOTER) TO THE GROUND STAKE WITH SCREWS.
STEP 8: TUBE SLIDE FOOTER SUPPORT ASSEMBLY 1: PLACE THE PARTS ON A FLAT SURFACE AND FASTEN AS SHOWN. 1857G FOOTER 3 1857H #8 X 2-1/2" Wood Screws (8 TOTAL) FOOTER 4 1857G FOOTER 3 2: SANDWICH FOOTER 1 BETWEEN THE FOOTER 2 PIECES AND FASTEN AS SHOWN. 1857F 1857E FOOTER 1 FOOTER 2 #8 X 2-1/2" Wood Screws (4 TOTAL) 1857E FOOTER 2 3: INSTALL MORE SCREWS AS SHOWN. #8 X 2-1/2" Wood Screws (8 TOTAL) #8 X 2-1/2" Wood Screws (2 TOTAL) 4: FASTEN THE SUPPORT BRACKET TO THE VERTICAL 1857F BOARD AS SHOWN.
STEP 9: TUBE SLIDE - FOOTER SUPPORT 1: IN ORDER TO INSTALL THE FOOTER SUPPORT ASSEMBLY INTO THE POSITION SHOWN YOU MAY HAVE TO DIG DOWN INTO THE YARD. THIS IS NORMAL. 2: REMOVE THE 3/4" LONG HEX BOLT AND REPLACE IT WITH A 1" LONG HEX BOLT FOR THE SUPPORT BRACKET. 3: INSTALL MORE 3/4" LONG BOLTS IN THE OPEN HOLES AS SHOWN. A UPON INSTALLATION THIS EDGE SHOULD BE EVEN WITH OR SLIGHTLY BELOW GRADE. FOOTER SUPPORT WILL BE PARTIALLY BELOW GRADE UPON INSTALLATION.
