Instructions for Use Washing machine
Thank you for your confidence in purchasing our washing machine, and congratulations on the excellent choice. Your new washing machine meets the requirements of modern treatment of laundry. It is rational in the consumption of energy, water and washing agents. Our appliances are friendly to the environment. Some of the materials may be recycled, others deposited or decomposed. To avoid pollution of environment, once your appliance is no longer useful, take it to your local authorized waste appliance dealer.
Description of washing machine 1. 2. 3. 4. Front panel Detergent dispenser Door (depending on the model) Filter lid 5. 6. 7. 8. Adjustable legs Water outlet hose Water inlet hose Mains power cable Technical information (depending on the model) • Max. load: 4,5 kg Dimensions slim aparat (w x d x h): 600 mm x 440 mm x 850 mm Depth with door open: 88 cm Weight (net): 76 kg Nominal voltage: 2000 W 141576 • Max.
Cautions • Be sure to remove transport brackets prior first use of the appliance. Attempted operation of the blocked machine may result in irreparable damage which is not covered by the manufacturer’s warranty! • When connecting your washing machine to water supply, be sure to use brand new water inlet hose and appropriate sealing gaskets (attached). • Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be damaged if frozen.
Installation and connection Package removal In removing the wrapping be careful not to damage the appliance with a sharp object. Before connecting the appliance, let it warm up to room temperature (wait for two hours). • Our appliances are packed in environmentally friendly materials which may be recycled, deposited or decomposed without any threat to the environment. • To this end all wrappings are marked accordingly. Removal of transport brackets • Move the pipes.
• If you have a tumble dryer of the same dimensions, you can place it on top of the washing machine. Water inlet connection To ensure correct operation of the appliance, water pressure inlet must be between 0,05 and 0,8 MPa. Minimum water pressure can be established by measuring the quantity of poured out water. 3 litres of water must be poured out from completely opened tap in 15 seconds.
Water outlet connection • Fix the outlet hose to run into the sink or the bathtub, or connect it directly to the wall drain outlet (diameter min. 4 cm). • Wall drain must be installed properly and must enable occasional cleaning. • Fasten the outlet hose support with a piece of rope led through the hose elbow, to prevent the hose from slipping to the floor. The end of outlet hose should be placed between minimum 60 cm and maximum 100 cm above the floor level.
Operation A B C D - program selector MENU knob SELECTION knob short program knob Program selector E F G H Basic programs - easy ironing knob START/PAUSE knob door knob (depending on the model) display Partial programs Cotton Heavy duty Rinse Synthetics Softening Delicate Pumping water Wool Spinning Manual wash Jogging Mix Functional knobs Knob B (MENU) - Use this knob to scroll around main menu. Knob C (SELECTION) - Use this knob to scroll around main menu.
Before first use - Selecting language To change the language in which the information appear on the display, press simultaneously the key MENU (B) and SELECTION(C), and turn the program selector (A) from position “0” to the first program in clockwise direction (Cotton 95°C). The name of actually selected language appears on the display. Scroll down the selection of languages by pressing the SELECTION knob (C), until you find the desired language. Then turn the program selector back to position “0”.
Washing machine operation 1. Name of the program, 2. Duration or time of day, 3. Symbols for activation of additional functions, 4. Water quantity in liters, 5. Spin RPM Program is selected by turning the program selector from the “0” position to the desired washing program. The display indicates particular washing program, selected by the program selector.
Delicate This is a program for delicate fabrics (dresses, skirts, blouses) and curtains. Wool Especially gentle program for washing wool and garments made from mixture of other fabrics with wool, appropriately marked for machine washing. Manual wash Very gentle program concluded with short gentle spin (max. 400 RPM). It is suitable for washing fabrics from flax, silk, wool or viscose, marked accordingly for manual wash.
are displayed in sequence. If you do not wish to activate or change certain displayed function, press knob B (MENU) to move to the next available function.Functions with the choice of multiple available settings, display the default one in bold (spin RPM, extra rinse, more water, sound signal). Using the SELECTION knob (C) you may change settings. Activation of a particular function is confirmed by the relevant symbol appearing on the display.
Pre-wash Used for washing heavily stained laundry, especially with superficial stains. In default setting the pre-wash function is off. It is activated by pressing the SELECTION knob (C) on programs for cotton, synthetics, delicate and mixed laundry. Soaking This program is intended for removal of stubborn stains. In default setting the soaking function is off. It is engaged by pressing the SELECTION knob (C). Soaking time may be set from 1 h to maximum 6 hours, in 30 minute steps.
SELECTION button (C) reset the selected time. Sound signal Sound signal beeps when a knob is pressed (function selection), and it also signals the end of washing program and reporting failures. In default setting the sound signal is on. You may select to switch the sound signal off, or increase volume. sound signal off Legend: normal sound signal setting increased volume setting If you switch the sound signal off the display indicates relevant symbol .
Rinse Independent program for rinsing delicate laundry, without intermediate spinning and with short final spin. You may use it for rinsing manually washed delicate laundry. You may engage the reduced spin RPM function. Softening This program is intended for softening, bleaching or impregnating of washed laundry. It is completed with aggressive spinning at high RPM. You may engage the reduced spin RPM function.
Start the operation Program is activated by pushing the START/PAUSE button (F). Sound signal confirms the start, the display indicates first washing stage and time left to the end of washing. Washing stages are consecutively displayed in accordance with the selected program. If the machine is set with the delayed start, it will start operating after the delay time expires. If the pump stop function was set, the program will stop at the final rinse and the display indicates flashing sign pump stop (RINSE).
it had been interrupted. Permanent suspension - change of program By turning the program selector to the position “0” the program is permanently suspended. Consequently you may select a new program (see Program selection). • Failures Program is suspended in case a failure occurs. This is signalled by the relevant reading on the display and a sound signal (see cf. Troubleshooting).
manner: - Press MENU (B) and Easy ironing knobs (E), and turn the program selector to the first clockwise program. Display reads SENSOR CALIBRATION. - Start calibration by pushing the START knob (F). The machine performs calibration procedure automatically. During the process the reading SENSOR CALIBRATION is flashing. When the procedure is completed, the display reads END. - Return the program selector (A) back to “0” position.
Tips for washing and energy saving • Before washing sort out the laundry according to the type, degree of dirtiness and color resistance. • Prior selecting the washing program consult the sewn tab with information on a particular piece of laundry (see Maintenance chart on the last page). • Wash separately the new colored textile products for the first time. • Wash heavily soiled laundry in small quantities and add more detergent. • Treat stubborn stains with special stain remover, it will save energy.
• Insert particularly delicate linen (stockings, delicate female underwear, etc.) into the special bag. • High spin RPM leave less moisture in laundry which dries out much quicker in the tumble dryer, thereby saving energy. Do not put clods of detergent into the soap dispenser as the tube in the washing machine may clog. Cleaning and maintenance Disconnect the washing machine from the mains before cleaning! • The casing should be cleaned with soft cloth and mild detergent.
• Wash it under running water using a brush, and dry it. Remove any leftover dried detergent from the bottom of the casing. • Clean the entire rinsing area of the washing machine with a brush, especially the nozzles on the upper side of the rinsing chamber. • Clean frequently the water inlet hose screen under running water. • After each wash wipe the door rubber gasket. This will prolong its useful life. • Open the filter lid using flat screwdriver or similar tool.
• Insert the filter back as shown on the picture (arrow and pointer), and tighten by turning it in clockwise direction. To ensure good sealing the gasket surface (A) must be dirt free. (depending on the model) Failures If the washing machine identifies failures in the operation, it reports it immediately. Sound alarm is heard and the display reads ERROR. Number identifies the type of failure.
Failure The machine does not work (display is not illuminated). Possible cause Machine is not powered. Water does not enter the machine. Filter is not tightly screwed in. Inlet pipe is not tightly screwed to the machine or to the water faucet. Outlet pipe fell to the floor. The machine is not properly leveled. Transport brackets are not removed. Unevenly distributed laundry, especially with very small quantities (for ex. only the bathrobe). Excessive measure of detergent.
Failure Softener is not completely rinsed, or water is left in the dispenser dish. Washing time is longer than usual. Time indicated on the display is corrected during the washing cycle. Possible cause Sucking cover is not correctly positioned or is clogged. • Low temperature of inlet water. • Due to unevenly distributed load, the machine has activated the UKS*. • Low mains voltage. • There has been a failure in the power supply. • Clean water sensor is engaged.
Tables Program chart - 7 kg WA 73xxx,... (depending on the model) Cotton 7 60 Cotton heavy * 7 60 Cotton 1700 RPM RPM 800 - 1700 95 Energy cons. kWh 1000 - 1700 7 Water cons. L 800 - 900 Temp. (°C) Cotton Spin max. (RPM) Type of laundry Max.
Program chart - 6 kg WA 63xxx,... (depending on the model) Energy cons.
Program chart - 6/7 kg WA 64xxx, WA 74xxx,... (depending on the model) kg Type of laundry Energy cons. kWh RPM RPM 6kg 1200 - 1800 Water cons. L 1200 - 1800 Spin max. (RPM) Temp. (°C) Max.
Program chart - 4,5 kg 95 Cotton 4,5 60 Cotton heavy * 4,5 60 Cotton 4,5 40 Synthetics 2 60 Synthetics 2 40 Synthetics 1400 1000 Energy cons. kWh Temp. (°C) 4,5 1000 - 1400 Max. load (kg) Cotton Spin max. (RPM) Type of laundry 800 - 900 Water cons.
z/z z/z z z z z/z z/z z z z Cold wash Soaking Pre-wash z Higher water level z Cotton heavy Spin speed Rinse hold Easy iron Cotton Short program Basic programs / Program Extra rinse / clean water sensor Program chart/Additional functions z Synthetics z z/z z/z z z z z Delicate z z/z -/z z z z z Wool z z/z z Manual wash z z/z z Jogging Mix z z z z/z -/z z z/z z/z z z z z Partial programs Rinse z/- Softening z/- Pumping water Spin z/- 141576
Maintenance chart Normal wash Max. washing temp. 95°C Delicate wash Whitening Max. washing temp. 40°C Max. washing temp. 60°C Whitening in cold water Max. washing temp. 30°C Manual washing Washing not allowed Whitening not allowed Ironing Hot iron max. 200°C Hot iron max. 150°C Hot iron max.
PS PG3,4 141576/en (03-08)
