MT IE GB Instructions for use, installation, and connection Glass-ceramic built-in coking hob
Glass-ceramic built-in cooking hob Dear customer! Glass-ceramic hob is intended for use in households. Our products are packed in environment-friendly materials which can be recycled, disposed of, or destroyed without imposing any burden on the environment. Instructions for use Instructions for use are intended for the user. They describe the appliance and its operation.
Important warnings • Installation of the appliance into a kitchen worktop and its connection to the power mains and the gas supply may only be performed by an adequately qualified technician. • Do not leave small children unattended when the appliance is in operation. Risk of burning and scalding! • During cooking, the overheated fat or oil on the hob may ignite. There is a risk of burning and fire; therefore, control the cooking process at all times. • Do not use the cooking hob for room heating.
Appliance description 1. Cooking zone rear left 2. Cooking zone front left 3. Cooking hob control unit 4. Cooking zone front right 5.
Cooking zones Before using the appliance for the first time Clean the glass-ceramic surface with a damp cloth and some manual dishwashing detergent. Do not use aggressive detergents such as abrasive cleaners that can scratch the surface, abrasive dishwashing sponges, or stain removers.
Cookware Tips on using the cookware Use high-quality cookware with a flat and stable bottom. • Transmission of heat is best when the pan bottom and the cooking zone are of the same diameter, and the pan is placed on the middle of the cooking zone. • When using a tempered glass (Pyrex) or porcelain cookware, please follow the cookware manufacturer’s instructions. • When using a pressure cooker, do not leave it unattended until the desired pressure is reached.
Operating the cooking zones • The cooking hob is fitted with electronic sensor keys which are activated, respectively, when the indicated surface of a particular sensor is touched with a finger for at least one second. • Activation of a sensor key is confirmed by a beep. • Do not place any objects on the sensor key surface (this may trigger error reports). • Make sure the sensor key surface is always clean. Turning on the cooking hob • Touch the on/off sensor key (A) and hold it for at least one second.
Turning off the cooking zones • Select the cooking zone by pressing the relevant sensor key (H). The decimal point (F1) next to the display for the selected cooking zone will light up. • Press the “–” (I) sensor key to set the power level to “0”. • Quick power off: the power level can be instantly set to “0” by pressing the “+” (G) sensor key and “–” (I) sensor key simultaneously. Turning off the cooking hob • The cooking hob may be turned off at any time by pressing the on/off sensor key (A).
hot. Be careful, as there is a risk of burning. If a power failure has occurred when the cooking zones were hot, the indicator “H” or “h” will flash. This is to warn you that the cooking zone may still be hot, but not necessarily, depending on how long the power supply was out of order.
Dish/cooking mode quantity power level cooking duration (min) Soup/reheating 0,5 – 1 lit A7 - 8 4-7 milk/reheating 0,2 – 0,4 lit A1 - 2 4-7 rice/simmering 125 – 250 g approx. 300ml - 600ml water A2 - 3 20 - 25 cooked jacket potatoes 750g – 1,5 kg approx. 600ml – 900ml water A5 - 6 25 - 38 fresh vegetables/ boiling 0,5 – 1 kg approx. 400ml – 600ml water A4 - 5 18 - 25 • The table below lists the examples of some dishes for which rapid heating is appropriate.
Power level u 1 2 3 4 5 6 7 8 9 Maximum operation time in hours 6 6 6 5 5 4 1,5 1,5 1,5 1,5 Temporary cooking progress suspension - STOP & GO (depending on the model) The STOP & GO function enables you to temporarily suspend, or pause the cooking progress (urgent other tasks), while keeping all the settings. Engaging the STOP & GO function • Cooing is temporarily suspended by touching the STOP & GO (C) sensor key. • A signal light (C1) will light up above the sensor key.
B Timer with the option to turn off the cooking zone The switch-off timer facilitates the cooking process by allowing you to set the cooking time for a particular cooking zone. In order to set the switch-off timer, the power level must already have been set (see section “Turning on the cooking zones”). • Press the timer sensor key (D) to activate the timer. “00” is displayed on the timer display (L) and the decimal point (F1) is lit.
To deactivate the timer before the set time has elapsed: • Select the desired timer display (see section Changing the timer setting) – the set time and the corresponding dot that indicates the cooking field will flash. • Press the “–” (I) sensor key to set the value to “00”, or press the “+” (G) and “–” (I) sensor key simultaneously, to reset the value to zero immediately. • If all power levels are set to “00”, the cooking hob will be turned off automatically after 10 seconds.
Cleaning and maintenance Cleaning Figure 1 Figure 2 Figure 3 Figure 4 243910 Figure 5 14 After each use of the glass-ceramic hob, wait for it to cool down and clean it; otherwise, even the smallest food residue will be burnt onto the hot surface next time you use the appliance. For regular cleaning and maintenance of the glass-ceramic surface, use special conditioning agents which form a protective layer on the surface, shielding it from dirt.
Installation Important warnings • Installation of the appliance into a kitchen worktop and its connection to the power mains may only be performed by an adequately qualified technician. • Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should be treated with heat resistant glue (100°C); otherwise, the worktop finish may be discolored or deformed.
Worktop cutout dimensions • Cooking hobs can be installed into worktops that are 30 to 50 mm thick. • The kitchen furniture element underneath the hob should not be fitted with a drawer. If the kitchen furniture element as a horizontal partition wall, it should be installed no less than 60 millimeters from the lower surface of the worktop. The space between the partition wall and the hob must be empty; no objects should be placed into that gap.
Connecting the appliance to the power mains Important warnings • • • • • • • • • The appliance may only be connected by an authorized skilled technician. Electric system protection should comply with all relevant regulations. The connection clips can be accessed when the connection clip covers are opened / removed. Before connecting the appliance, make sure the voltage indicated on the rating plate is consistent with the voltage in your home circuit.
Connection diagram • Incorrect connection may destroy parts of the appliance, making the warranty void. • Before connecting the appliance, make sure the voltage indicated on the rating plate is consistent with the voltage in your home network.
Technical characteristics Rating plate Serial number Code Model Type Trademark Technical information Compliance indications / symbols WE RESERVE THE RIGHT TO MAKE ANY CHANGES THAT DO NOT AFFECT THE FUNCTIONALITY OF THE APPLIANCE.
SVK_ORAITO 243910/en (03-10)
