Operation Manual

Instructions for use, installation and connection
41
Oven illumination
• When the oven is on, the lamp is also on, regardless of the
operation mode.
• If the oven is off, touch the sensor (1) and select the symbol
"Light" (1), then touch the light ON/OFF sensor (5) turn the
lamp on. Next touch of the ON/OFF sensor turns the lamp
off.
Selection and setting of oven temperature
After selecting the type of food and oven function mode, by
pressing the sensors (3a/3b) you may select the desired oven
temperature in the range from 30 – 250°C (depending upon the
selected operation mode) in 5°C intervals.
During the operation, oven temperature may
be randomly increased or decreased within
the permitted temperature range (see chart)
by pressing the sensors (3a/3b).
Table of data for operation mode (with a sensor 2)
Operation mode
Preset
temperature (°C)
200 160 200 170 250 160 160 150 -
Preset time
(h/min)
---------
Possibillity of max.
set temperature (°C)
250 250 250 250 250 220 220 200 -
Oven thermostat signal lamp (d3-2)
• Signal lamp is on; oven temparture is below the setting and
the oven is heating.
• Signal lamp is off; the temperature in the oven has reached
the set temperature.
• Signal lamp is flashing regularly; the oven is set to the end of
operation mode with the adequate sensor (d4-2); the
preparation of food has not started as yet (the appliance
automatically computes the relevant moment of starting the
oven operation).
Setting the operation time
• The time of oven operation may be selected in the range
from 0 to 6 hours, in 1 minute intervals.
• After selecting the function mode and the temperature, by
pressing the sensor 4 you may now select the operation time
from 0 to 6 hours, in 1 minute intervals.
• Touch the selection sensor (4), the display
(d4-1) starts flashing. By touching sensors (4a/4b) set the
desired operation time.
• Turn the oven on with the ON/OFF sensor (5).
• When the set time has elapsed, the oven is switched off
(signalled by the beep, oven operation time symbol (d4-1)
and the relevant signal lamp (5a) are flashing).
• By touching any sensor (except the ON/OFF sensor (5),
which turns the sound signal off and switches the oven on)
you may switch the sound signal off, otherwise it is turned off
automatically after 7 minutes.
Oven operation time may be changed during
the operation.
Setting the end of operation time
• This function is used when you wish to select the end of
operation (cooked food) at exactly the pre-selected time.
• The function may be used only with previously set time of
operation ((d4-1) is on).
• By touching the selection sensor (4) symbol (d4-2) flashes,
and the display (d4-6) flashes the sum of daily current time
and the oven operation time. Use the sensor (4a) to set the
desired end of oven operation.
• Switch the oven on with the ON/OFF sensor (5). The
appliance awaits the start of operation (oven thermostat
signal lamp symbol flashes regularly (d3-2), oven operation
time symbol is on (d4-1) and end of operation time symbol
(d4-2) is also on.
• The starting time is now defined automatically. At the
moment the oven starts the operation, the end of operation
symbol (d4-2) goes off, oven illumination is on, and the oven
thermostat signal lamp (d3-2) is on until the set temperature
is reached.
• Eventual immediate start of operation may be provoked by
simultaneous pressing of sensors (4a/4b) (for approximately
5 seconds).
Alarm timer
This function may be applied separately, and is not in
connection with the oven operation. It is use whenever you
wish to be warned at a pre-selected time.
• By touching the selection sensor (4) provoke flashing of the
alarm timer symbol (d4-4) (the display (d4-6) flashes
"»00:00«). Set the desired time with sensors (4a/4b) in the
range from 0 to 99 minutes in 1 minute intervals. The
countdown starts after approximately 5 seconds, the alarm
timer symbol (d4-4) is on, the display (d4-6) indicates the
current time.
• By touching the selection sensor (4) you may check and
correct the remaining time, indicated on the display (d4-6).
• By simultaneous pressing of sensors (4a/4b) (approximately
5 seconds) the remaining time may also be set to »00:00«.