Operation Manual

Instructions for use, installation and connection
40
Prior first use
Oven
Take all the accessories out of the oven and clean it with warm
water and your usual mild detergent. Never use aggressive
cleaners as they might cause scratches!
During the first heating the oven might produce a somewhat
unpleasant smell of a new product. This is normal, just
ventilate the place thoroughly!
Tips for the use of oven
• If possible use dark, silicone coated or enamel baking pans,
because of their excellent thermal conductivity.
• Preheating of oven is necessary only if recommended by the
recipe or if written in the chart below.
• Heating of empty oven consumes a lot of energy. Save it by
baking several pizzas or cakes consecutively, one after the
another, while the oven is still warm from the previous
one.Towards the end of baking, the oven may be switched
off about 10 minutes before the pletion, thereby making use
of the remaining.
General setting options in oven control
• Sound signal volume
− When no other function is active it is possible to set the
sound signal volume by touching the sensor (4b). The
display (d4-6) indicates symbols of 4 volume levels.
• Sound signal duration:
− oven operation period sound signal (d4-1), end of oven
operation (d4-2) and meat probe (d4-3) last 7 minutes;
− alarm timer sound signal (d4-4) lasts 3 minutes
− After the expiry of indicated time the sound signal goes
off automatically.
• Each proper touch of sensor is accompanied by a beep.
• Changing the value setting speed
The value setting speed is doubled after 5 seconds of
continuous sensor pressing.
• Simultaneous pressing of (-) and (+) sensors (3a/3b) ali
(4a/4b)
Resets the settings to “0”, except for the temperature
setting display (d3-1) which is changed to 30°C, and the
end of operation sensor (d4-2) which changes to indicate
the time of day.
In case the ON/OFF sensor (5) is not pressed within 5
seconds, all settings are reset automatically, except for the
time of day and the alarm timer.
<
In case of eventual power failure which is less
that 1 minute long, all settings remain
unchanged and the oven resumes normal
operation (if activated).
Use of oven
Alternatives with the oven on:
• Changing or setting the oven temperature
(d3-1)
• Changing or setting oven operation time (d4-1)
• Changing or setting end of oven operation
(d4-2)
• Changing or setting meat probe temperature (d4-3) if the
meat probe is connected
Alternatives with the oven off:
• By using the food selection sensor (1) or mode selection
sensor (2) you may select the type of food (1) or function
mode (2), and you may change or set the oven temperature
(d3-1), oven operation time (d4-1), end of oven operation
(d4-2), meat probe (if the type of food or function mode had
been selected before) (d4-3) alarm timer (d4-4) and the time
of day (d4-5).
• changing or setting the alarm timer and the current daily time
(d4-4).
Setting the time of day
• After the appliance is connected to the mains the display
(d4-6) flashes »12.00« and the symbol (d4-5).
• By touching the sensors (4a/4b) you may set the exact daily
time (approximately 5 seconds after the setting is finished
the symbol (d4-5) goes off and the display (d4-6) indicates
the correct daily time.
Changing the current daily time
The time of day may be changed at any time (except in case of
activated end of operation mode (d4-2) is on) by doing the
following:
• Touch the selection sensor (4) and select the current time
selection mode ((d4-5) is flashing).
• by means of sensors 4a/4b set the current time (symbol (d4-
5) and the time displayed are flashing (d4-6))
• after 5 seconds the display indicates (d4-5) correct current
time (symbol (d4-5) goes off).
• in case of power failure shorter than 1 minute, the current
daily time remains unchanged.