3D Hero System ® User Manual + Warranty Info
Firmware Update The 3D HERO System requires two 1080p HD HERO cameras. You will need to make sure both of your HD HERO cameras have the latest firmware installed before using the 3D HERO System. To download the latest firmware, visit: gopro.com/firmware. REQUIRED FREE 3D EDITING SOFTWARE: GoPro CineForm Studio™ Your 3D HERO System allows you to combine two 1080p HD HERO cameras with a 3D HERO Sync Cable to record synchronized videos and photos.
D HERO SysteM Features 1. Master Shutter Button Controls Both Cameras 2. Right Camera Power Button 3. Left Camera Power Button 5. Mounting Fingers 4. Center Mount Adapter 6. 3D HERO Sync Cable 7. Waterproof Housing 8.
ASSEMBLING 3D HERO SYSTEM COMBINING Two CAMERAS FOR 3D VIDEO AND PHOTO CAPTURE NOTE: The 3D HERO System requires two 1080p HD HERO cameras. Each camera requires a fully charged battery and SD card with sufficient memory for recording (GoPro recommends Class 4 or faster SD cards). Each camera’s settings (e.g.: resolution, exposure, record mode, video format (PAL & NTSC)) must match for 3D synchronization to work.
To combine cameras in 3D HERO System waterproof housing: 1. O pen back door to the 3D housing. 2. Insert “right” camera right side up into housing. 3. Insert “left” camera upside down into housing. 4. Insert the 3D HERO Sync Cable into the HERO Bus Port on both cameras. The side that says “R” on the sync cable attaches to the right camera while side that says “L” on the sync cable attaches to the left camera.
USING THE 3D HERO System Additional Notes: IMPORTANT: To capture 3D video and photos, both cameras must be set to identical resolution, record mode and frame rate settings. • Blinking front LCD screen and red LED record lights may or may not blink in sync. This is OK and has no effect on whether or not each camera is in sync with the other. To begin recording video or photos: • Should the battery die or SD card become full on either camera, both cameras will save the files and stop recording. 1.
MOUNTING CONFIGURATIONs IMPORTANT: It is recommended to use dual quick-release buckles for mounting the 3D HERO System whenever possible for maximum stability. Using a single center mounted quick-release buckle is only recommended for chest, helmet, suction cup, and other body worn applications where high vibration or impact are less likely. Use of a single center quick-release buckle in high vibration or high impact scenarios can result in less stable video compared to using two quick-release buckles.
Curved and Flat Surface Mounting The extension arms and quick-release buckles can be used in a number of different orientations depending on what type of surface you are attaching the 3D HERO System to. For example, attach included extension arms to the quickrelease buckles in order to achieve proper orientation when attaching the waterhousing to curved surfaces. Note: When removing the quick-release buckles from the adhesive mounts, push both quick-release buckles out evenly to avoid jamming the buckles.
VIDEO RECORDING TIPS • For best results, keep your subject at least 3 feet away from camera when shooting in photo mode 720p and 960p resolutions. When shooting in 1080p, because of its less wide angle perspective, it’s best to keep your subject at least 5 feet away from the camera. Failure to do so will result in an inability to properly align the two video files for 3D and will cause your eyes to strain when viewing the subject on screen.
Transferring Video And Photos To YOUR Computer Creating 3D Video and Photos with GoPro CineForm Studio Plug the camera into your computer with the included USB cable, turn on the camera, and locate the Removable Disk (SD Card) icon. Once the icon is located: To convert 2D video and photo files into 3D files, you will need to use GoPro CineForm Studio software. GoPro CineForm Studio and associated instructions are available as a FREE download from: gopro.com/3D. 1. Double click the “Removable Disk” icon.
IMPORTANT SAFETY + HANDLING INFORMATION Avoiding Water and Wet Environments When Not in Water Housing WARNINGS Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage to the 3D HERO System or other property. Do not use the 3D sync cable in rain, near wash basins, or in other wet locations when cameras are not inserted in the water housing. Do not spill any food or liquid on the 3D sync cable.
Warranty This product is guaranteed against manufacturing defects for one (1) year from the original date of purchase. GoPro’s sole obligation in the event of such defects during this period is to repair or replace the defective part or product with a comparable part or product at GoPro’s sole discretion. Except for such replacement, the sale, or other handling of this product is without warranty, condition or other liability even though the defect or loss is caused by negligence or other fault.
