Installation Instructions

ManualsBrandsGoof Proof Showers ManualsFlooring & RugsKirb-Perfect

Kirb-Perfect®

(2) Attach top panel

to assembled side

panels using the

(8) 3/4” stainless

self-tapping screws

supplied.

(Be sure the arrows

on top panel are

pointed to inside of

the shower. Do not

over tighten.)

(5) Pack and ll side and top panels of attached

curb with mud.

(We recommend a lightweight wall mud for ease

of workability.)

(4) Fit assembled

curb over membrane

wrapped 2x4s, attach

with galvanized nails

(not supplied) to the

exterior only.

(Caution: Do not

nail to inside of

curb, doing so

will jeopardize the

integrity of the liner!)

(6) Let curb dry over night and use a latex modied mortar to set tile.

(Note: We recommend a roll-on waterproong membrane to be added to the

surface of the curb for additional protection prior to the installation of tile.)

LIFETIME WARRANTY - Mark E Industries, Inc. warrants that Kirb-Perfect® products are free from defects in materials and workmanship. Warranty does not cover

damage due to obvious misuse, abuse or modication. We will repair or replace without charge, at our option, any part that should prove defective. Part(s) must be

returned, freight prepaid, with proof of purchase.

Instructions for

membrane wrapped curb

Be sure liner is installed according to all

ANSI specications and Plumbing codes.

(3) Trim inside panel

to allow for pre-

pitch, using snips,

hacksaw or

grinder.

(1) Assemble the 2 side panels

with the (2) 1 1/4” screws

supplied.

(Be sure not to over tighten)

Anchor Holes (only

for use on OUT-

SIDE of membrane

wrapped 2 x 4s)

Manufactured by:

MARK E INDUSTRIES

28921 US Hwy. 19 N. Clearwater, FL 33761

Toll Free: 1-866-771-9470

http://www.kirb-perfect.com/kirb-perfect.html

e-mail: info@markeindustries.com

Summary of content (4 pages)

PAGE 1
Kirb-Perfect® Instructions for membrane wrapped curb Be sure liner is installed according to all ANSI specifications and Plumbing codes. Anchor Holes (only for use on OUTSIDE of membrane wrapped 2 x 4s) (1) Assemble the 2 side panels with the (2) 1 1/4” screws supplied. (Be sure not to over tighten) (2) Attach top panel to assembled side panels using the (8) 3/4” stainless self-tapping screws supplied. (Be sure the arrows on top panel are pointed to inside of the shower. Do not over tighten.
PAGE 2
Kirb-Perfect® Instructions for non-wood curb Be sure liner is installed according to all ANSI specifications and Plumbing codes. Anchor Holes (only for use on OUTSIDE of membrane wrapped 2 x 4s) (1) Trim inside panel to allow for prepitch, using snips, hacksaw or grinder. (2) Hold liner up in center of curb and position between center posts. Screw together with the (2) 1 1/4” screws supplied. (Be sure not to over tighten.) Trim excess liner even with top of center post.
PAGE 3
Kirb-Perfect® Instruciones para el bordillo con membrana Asegúrese de que el forro se instale de acuerdo a las especificaciones ANSI y los códigos de plomería. Agujeros de anclaje (solo para usar en la pared EXTERNA de la membrana de 2 x 4s) (1) Ensamble los 2 paneles laterales con los dos tornillos suministrados de 1 ¼ “.
PAGE 4
Kirb-Perfect® Instrucciones para el bordillo sin madera Asegúrese de que el forro se instale de acuerdo a las especificaciones ANSI y los códigos de plomería. (1) Corte el panel interior para darle espacio al prepitch, usando tijeras, sierra para metales o afilador. Agujeros de anclaje (solo para usar al EXTERIOR de la membrana de 2 x 4s) (2) Mantenga el forro hacia arriba en el centro del bordillo y colóquelo entre los postes centrales. Sujételo con los (2) tornillos de 1 ¼ “ suministrados.