BioSpray®-10C Surface Sanitation System Operating and Maintenance Instructions Read before operating.
CONTENTS: GENERAL...................................................................................................................................... 3 IMPORTANT SAFETY INSTRUCTIONS...................................................................................... 3 IDENTIFYING MAIN PARTS........................................................................................................ 4 INSTALLATION/SETUP.............................................................................................
GENERAL The BioSpray®-10C unit is designed for intermittent use and will come with a 10 lb. capacity CO2 tank. Continuous use for 20 minutes will result in freezing and the tank will need time to thaw. WARNING IMPORTANT SAFETY INSTRUCTIONS To prevent operator injury and damage to the equipment, please read and observe the following basic safety precautions: 1. Read and understand all instructions before using. 2. Keep this manual with the unit at all times. 3.
IDENTIFYING MAIN PARTS (BioSpray®-10C) Spray Gun Regulator Spray Gun Pressure Gauge CO2 Tank Pressure Gauge Coil Hose Front Stand Outlet Connector Rear Door Wheels 4 BIOSPRAY®-10C 1020
INSTALLATION/SETUP 1. Remove from packaging and inspect unit. If anything is damaged, contact Goodway Technologies immediately (800-333-7467). 2. Place the surface sanitization system on a flat surface. Installing the CO2 Tank (BioSpray®-10C): 1. Open the rear door 2. Detach and loosen both straps that will hold in the 10 lb. CO2 tank 3. Carefully install new tank against brackets, on top of rubber pads on left hand side of the unit. Make sure the connector on the tank is facing to the right. 4.
OPERATING INSTRUCTIONS 1. Attach Goodway approved formula to spray gun. NOTE: To do this, carefully remove the foil seal on the top of the bottle, making sure that no debris gets into the bottle, as that will impede the spraying. Be careful not to overtighten the bottle, it only has to be snug to seal. 2. Connect the spray gun to the coil hose. 3. Connect the coil hose to the outlet connector on the top of the unit. 4. Open the CO2 tank valve by turning it counter clockwise ¾ - 1 turn. 5.
INCREASING THE PRESSURE: When increasing the pressure of this BioSpray® unit, be aware of the following: 1. The pressure may need to be increased for spraying longer distances or for the removal of bio-burdens. 2. The standard PSI rating for operation is 24-26 PSI while spraying. After intermittent use at higher pressure, the regulator should be reset to 24-26 PSI. 3. To increase the pressure, turn the regulator clockwise until you reach the desired pressure.
TIP: Depending on your usage, volume and needs, it is recommended to have an extra set of CO2 tanks on hand, so that you can continue using your BioSpray® System while your empty CO2 cylinders are being refilled. WARNING: Use only 10 lb. (BioSpray®-10C) preferably aluminum tank with a 7” diameter. If a spare tank is needed, please call Goodway Technologies at (800) 333-7467 toll-free or email us at goodway@goodway.com. Do not use any CO2 tank with a dip tube.
TECHNICAL INFORMATION Operating Pressure 24-26 PSI Working Tank Pressure 800-1000 PSI (Full Tank) Operating Environmental Temperature 68°F +/- 20°F (20°C +/- 11°C) Air Flow 5.4 CFM Siphon Rate 160 mL/min (5.4oz/min) Tank Safety Relief 3000 PSI Regulator Safety Relief 150 PSI TROUBLESHOOTING Problem Constant ‘hissing’ noise Spray gun is sputtering Cause Solution Damage to spray gun or coil hose Check both parts to be sure where the damage has occurred.
PARTS BREAKDOWN (BioSpray®-10C) 6 4 5 8 3 9 7 2 14 1 11 16 15 10 13 12 PARTS NUMBER (BioSpray®-10C) Pos Part Number Description Qty 1 SANI-091 Cover 1 2 SANI-096 Bottle Holder 3 3 SANI-100 Bottle Stop 1 4 SANI-014 0-160 PSI Pressure Gauge, Regulator 1 5 SANI-015 0-2000 PSI Pressure Gauge, Tank 1 6 811 Handle Hook 1 7 9672 Door Hook 1 8 SANI-092 Rear Door 1 9 SANI-009 Latch, Rear Door 2 10 6226 Wheel 2 11 SANI-101 Hinge, Rear Door 5 12 9008 Foot 2
NOTES BIOSPRAY®-10C 1020 11
HVAC & FACILITY MAINTENANCE SOLUTIONS Provides innovative maintenance solutions for a wide variety of industries including commercial HVAC, food and beverage processing, power generation and manufacturing. For Sales Call: 1-800-333-7467 For Service Call: 1-800-370-2855 GOODWAY® TECHNOLOGIES CORPORATION 420 West Avenue, Stamford, CT 06902 USA Tel: 203-359-4708 · Toll-Free Tel: 800-243-7932 Fax: 203-359-9601 · Toll-Free Fax: 800-359-9625 Email: goodway@goodway.com Visit: www.goodway.
