Installation Instructions

ManualsBrandsGoodman ManualsFurnacesMasonry Vent Kit - Upflow

Description

This kit is for use on 80% AFUE, 33” tall “H” and “S” model

furnaces installed in the upflow position only. This field in-

stalled kit may be used when a single forced draft furnace is

independently vented into a tile lined masonry chimney. This

kit may only be used with interior masonry chimneys or

qualifying exterior masonry chimney applications identified in

tables on Page 7.

The kit incorporates a flue high limit safety switch which will

interrupt power to the gas valve when a backdraft condition

exists.

The table on page 2 lists the kit number, the applicable models,

and the limit setting. The appropriate kit must be matched to

the appropriate model number for safe and reliable operation.

MVK-01 & MVK-02

MASONRY VENT KIT

INSTALLATION INSTRUCTIONS

ATTENTION INSTALLING PERSONNEL

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION

Prior to installing this masonry vent kit, refer to the National

Fuel Gas Code (NFPA 54ANSI Z223.1) or in Canada, CAN/

CGA-B149.2-M91 to ensure that the installation is in compli-

ance with those and all local codes. Prior to installation,

ensure the condition of the masonry chimney meets the

requirements outlined in the National Fuel Gas Code (NFPA

54/ANSI Z223.1), or the Standard for Chimneys, Fireplaces,

Vents, and Solid Fuel Burning Appliances (NFPA 211), or in

Canada, CAN/CGA-B149.1 and .2.

PLEASE READ AND FOLLOW THESE INSTRUCTIONS

CAREFULLY.

As a professional installer, you have an obligation to know the product better than the customer.

This includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety warnings.

Often during installation or repair, it is possible to place yourself in a position which is more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough

to be able to instruct a customer in its safe use.

Safety is a matter of common sense... a matter of thinking before acting.

Most dealers have a list of specific, good safety practices... follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, if there is a direct conflict

between existing practices and the content of this manual, the precautions listed here take precedence.

NOTE: Information contained in this manual (IO-754*),

supersedes MVK-01 and MVK-02 data found in the furnace IO.

I0-754D

June 2013

Summary of content (8 pages)

PAGE 1
MVK-01 & MVK-02 MASONRY VENT KIT INSTALLATION INSTRUCTIONS Description This kit is for use on 80% AFUE, 33” tall “H” and “S” model furnaces installed in the upflow position only. This field installed kit may be used when a single forced draft furnace is independently vented into a tile lined masonry chimney. This kit may only be used with interior masonry chimneys or qualifying exterior masonry chimney applications identified in tables on Page 7.
PAGE 2
CONTENTS KIT CONTENTS Important Information .......................................................... Kit Contents ....................................................................... Model List .......................................................................... Tool List ............................................................................. Masonry Vent Kit Instructions ............................................ Wiring Diagram ..........................................................
PAGE 3
NOTE: MVK-02 bottom plate includes a keying tab. Furnace models for which the MVK-02 is approved has a keying slot in the furnace top. The keying tab on the MVK-02 fits into the keying slot in the furnace top on applicable furnace models. Verify that the masonry vent kit model is applicable to your furnace model prior to installation. If your furnace model is correct for the MVK02 and the keying slot is not present on the furnace top, furnace top 0121F00463DG must be purchased.
PAGE 4
6. Position the masonry vent kit body to the bottom plate and secure using the (2) screws supplied with the vent kit. The safety limit must be on the right side when facing the furnace. Ensure the flue pipe inside the masonry vent kit fits over the furnace flue top. 8. Masonry Vent Kit Wiring a. Locate the 2-wire wiring harness included with the masonry vent kit. b. Locate the wiring harness end with (2) female 1/4” quick connect terminals.
PAGE 5
CHIMNEY INSPECTION CHART Refer to the National Fuel Gas Code (NFPA 54/ANSI Z223.1), or the Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances (NFPA 211) or, in Canada, the Canadian Installation Codes (CAN/CGA-B149.1 and .2) for additional requirements.
PAGE 6
MASONRY CHIMNEY FLUE CAPACITIES - SINGLE FURNACE WITH TYPE B DOUBLE WALL VENT CONNECTOR Height, Late ral H, (ft) , L, (ft) Minim um Internal Chim ney Are a 28 in2 38 in2 50 in2 63 in2 78 in2 95 in2 Appliance Input Ra ting in Thousa nds of Btu per Hour 86 130 180 247 320 401 82 117 165 231 298 376 6 2 5 8 2 5 8 93 88 83 145 134 127 198 183 175 266 247 239 350 328 318 446 423 410 10 2 5 10 103 96 87 162 148 139 221 204 191 298 277 263 388 365 347 491 466 444 15 2 5 10 15 114 107 97 89 1
PAGE 7
EXTERIOR MASONRY CHIMNEY APPLICATIONS TABLE PERMITTED EXTERIOR CHIMNEY APPLICATION * ** MINIMUM 99% WINTER DESIGN TEMPERATURE* PERMITTED CHIMNEY +17°F (-8°C) or Warmer ** Exterior Masonry Chim neys The 99% Design Dry-Bulb (db) temperatures are found in the 2005 ASHRAE Fundamentals Handbook CD and Chapter 28. Fig. G.2.4 in the NFPA54/ANSI Z223.1-2009 (Appendix G) also provides winter design temperatures for some locations. Chimneys with one or more sides exposed to the outdoors below the roof line.
PAGE 8
NOTE: SPECIFICATIONS AND PERFORMANCE DATA LISTED HEREIN ARE SUBJECT TO CHANGE WITHOUT NOTICE Quality Makes the Difference! All of our systems are designed and manufactured with the same high quality standards regardless of size or efficiency. We have designed these units to significantly reduce the most frequent causes of product failure. They are simple to service and forgiving to operate. We use quality materials and components. Finally, every unit is run tested before it leaves the factory.