Installation Instructions

20
HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING.
MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO
MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING
RYCON
COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2
W2
E
C
Y2R
R
Y2G
IF NEEDED
HEATPUMP - 2 STG EMHT 1 STG AUX - 1 OUTDOOR T'STAT
Y1
Y1
O
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
C
R
Y1
W2W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1
THERMOSTATS
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
ROOM
THERMOSTAT
2-SPD HEATPUMP
1st STAGE HEATER
2nd STAGE HEATER
NO AUX HEAT IN HEATPUMP MODE UNTIL T’STAT CLOSES
O
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.)
W2 AND OT2 CLOSED ENABLES HI SPD
FAN HEATING
E ENABLES LOW SPD FAN HEATING
3.) OT1 PJ4 AND OT2 PJ2 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE “OFF” POSITION
OUTDOOR
THERMOSTAT
REMOVE
PRODUCTION
WIRE Y1-O
Figure 33
TWO STAGE COOLING WITH CONVENTIONAL TWO STAGE THERMOSTAT
(ENCLOSED WITH ADD ON 1N006 DIODES)
TSTWK01 KIT REQUIRED
ENCODED THERMOSTAT
PN. B136827 1 REV. A
ZD2
ZD3
ZD1
TEST
1N4005
DIODES
PN. B1368274
PJ6
PJ2
PJ4
HUM
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
24 VAC
Y1
HEATPUMP
Y1 Y/Y2 HUM
HUMIDISTAT
THERMOSTATS
24 V
230 V
2 SPD REMOTE
CONDENSING
UNIT
TSTWK01
BOARD
TO COMMON ON
TSTWK01 BOARD
TO Y ON
TSTWK01 BOARD
HUMIDISTAT
(OPTIONAL)
HUMIDISTAT
(OPTIONAL)
SEE NOTE 1
NOTES:
1.) STAT OPENS ON HUMIDITY RISE
2.) DIP SWITCH #4 MUST BE IN THE ON POSITION
CUT HUM PJ6 FOR HUMIDISTAT OPERATION
2ND STAGE HEATER
1ST STAGE HEATER
CUT OT1 PJ4 FOR 2-STAGE HEAT OPERATION
TSTWK01
TRANSFORMER
ENCODED 2 SPD COOLING - WITH 1 OR 2-STG HEAT
Figure 34
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.