Installation Instructions

19
HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING.
MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO
MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING
RYCON
COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2
W2
E
C
Y2R
R
Y2G
IF NEEDED
HEATPUMP - 2 STG EMHT 2 STG AUX - 1 OUTDOOR T'STAT
Y1
Y1
O
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCONCOM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
C
R
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1
THERMOSTATS
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
ROOM
THERMOSTAT
2-SPD HEATPUMP
1st STAGE HEATER
2nd STAGE HEATER
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.)
W2 ENABLES LOW SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD
FAN HEATING.
E ENABLES LOW SPD FAN HEATING
3.) IF OT2 PJ4 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE “OFF” POSITION
O
1ST STAGE AUX HEAT ENABLED BY ROOM T’STAT
2ND STAGE AUX ENABLED BY ROOM T’STAT AND OUTDOOR T’STAT
REMOVE
PRODUCTION
WIRE Y1-O
Figure 31
RYCON
COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2 W2
ECY2R RY2G
IF NEEDED
HEATPUMP - 2 STG EMHT 2 STG AUX - 2 OUTDOOR T'STATS
Y1 Y1O
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
C
R
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1
OTCW/W2E\W1
THERMOSTATS
OT1 OT2OTC
OUTDOOR
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
ROOM
THERMOSTAT
2 SPD HEATPUMP
1st STAGE HEATER
2nd STAGE HEATER
OT1
O
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.)
W2AND OT1 CLOSED ENABLES LOW SPD FAN HEATING
W2 AND OT2 CLOSED ENABLES HI SPD FAN HEATING.
E ENABLES LOW SPD FAN HEATING
3.) OT1 PJ4 AND OT2 PJ2 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE “OFF” POSITION
NO AUX HEAT IN HEATPUMP MODE UNTIL OUTDOOR T’STAT CLOSES
OT2
REMOVE
PRODUCTION
WIRE Y1-O
Figure 32
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.