Installation Instructions

18
HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING.
MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO
MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WARNING
R
YCON COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2
W2
EC
Y2R
RY2G
IF NEEDED
HEATPUMP - WITH 1 STG EMHT 1 STG AUX HEAT
Y1
Y1
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
R YCON
COM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
C
R
Y1
W2
W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1
THERMOSTATS
O
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
O
1st STAGE HEATER
2nd STAGE HEATER
ROOM
THERMOSTAT
2 SPD HEATPUMP
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.) E AND W2 ENABLE HI SPD FAN COOLING
3.) IF OT2 PJ2 JUMPER IS CUT “E” AND “W2”
ENABLE LOW SPD FAN HEATING
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE “OFF” POSITION
REMOVE
PRODUCTION
WIRE Y1-O
Figure 29
RYCON
COM
O
W2 ED
HEATPUMP
CONDENSER
CO
W2 W2
ECY2R RY2G
IF NEEDED
HEATPUMP - 2 STG EMHT 1 STG AUX HEAT
Y1 Y1
J1
R1
R3
CR10
R2
CR9
PJ6
PJ2
PJ4
OT1
OT2
HUM
12345678
PLEASE REFER
TO MANUAL
FOR PROPER
DIP SWITCH
CONFIGURATION.
W1 W2
RYCON
COM
O
W2 ED
S
WI
TC
H
DI
P
O
N
O
FF
24 VAC
C
R
Y1
W2W1
OUTDOOR
HEATPUMP
CONDENSER
DS1
CR1
CR2
CR5
CR6
CR7
CR8
CR3
CR11
J2 J3
1
4
C2
1
5
Y1RC G Y/Y2OT2 HUM
HUMIDISTAT
OT1OTC
W/W2E\W1
THERMOSTATS
O
HUMIDISTAT
(OPTIONAL)
SEE NOTE 4
ROOM
THERMOSTAT
2 SPD HEATPUMP
1st STAGE HEATER
2nd STAGE HEATER
O
NOTES:
1.) Y ENABLES HI SPD FAN COOLING
2.)
W2 ENABLES HI SPD FAN HEATING
E ENABLES LOW SPD FAN HEATING
3.) IF OT2 PJ4 MUST BE CUT FOR THIS
CONFIGURATION
4.) CUT HUM PJ6 JUMPER IF USING HUMIDISTAT
STAT OPENS ON HUMIDITY RISE
5.) DIP SWITCH #4 MUST BE IN THE “OFF” POSITION
REMOVE
PRODUCTION
WIRE Y1-O
Figure 30
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.