LPKMOD Installation Instructions

ManualsBrandsGoodman ManualsFurnace AccessoriesPropane (LP) Conversion Kit for GCVM961005DX

DESCRIPTION

This natural gas to L.P. (liquid petroleum) gas conversion kit

allows modulating

furnaces to be used on L.P. gas applications.

The following table lists the kit number and the applicable mod-

els. The appropriate kit must be matched to the appropriate

model number for safe and reliable operation. Upon opening the

kit, please verify that all parts are in an undamaged condition. IF

ANY DOUBT EXISTS ABOUT THE CONDITIONS OF ANY COM-

PONENT WITHIN THIS KIT, DO NOT USE THIS KIT AND CON-

TACT YOUR SUPPLIER FOR A NEW KIT.

MODEL LIST

LP KIT MODEL

*MVM960603BX

DM96MC0603BX

*MVM960805CX

DM96MC0805CX

*MVM961005DX

DM96MC1005DX

*MVM961155DX

DM96MC1155DX

*CVM960604CX

DC96MC0604CX

*CVM960805DX

DC96MC0805DX

*CVM961005DX

DC96MC1005DX

MODEL LIST

LPKMOD100CF

LPKMOD060UF

LPKMOD080UF

LPKMOD100UF

LPKMOD115UF

LPKMOD060CF

LPKMOD080CF

*=A or G

CONTENTS OF KIT

KIT QTY

Installation Instructions 1

L.P. Burners 3

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 4

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 5

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 5

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 3

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 4

Gas Valve \ Manifold Assy. 1

Installation Instructions 1

L.P. Burners 5

Gas Valve \ Manifold Assy. 1

DESCRIPTION

LPKMOD100UF

LPKMOD080UF

LPKMOD060UF

LPKMOD100CF

LPKMOD080CF

LPKMOD060CF

LPKMOD115UF

All of the fasteners removed to perform this conversion are to

be reused. Any component found to be damaged due to this

conversion must be replaced with factory authorized replace-

ment parts before this furnace can be put into operation.

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to know the product better than the customer.

This includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual.

Pay special attention to all safety warnings. Often during installation or repair it is possible to place

yourself in a position which is more hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product safely and to know it well enough

to be able to instruct a customer in its safe use.

Safety is a matter of common sense...a matter of thinking before acting.

Most dealers have a list of specific good safety practices...follow them.

The precautions listed in this Installation Manual are intended as supplemental to existing practices.

However, if there is a direct conflict between existing practices and the content of this manual,

the precautions listed here take precedence.

LPKMOD CONVERSION KITS

MODULATING FURNACE

NATURAL GAS TO L.P. GAS CONVERSION

IO-769A

September 2013

Summary of content (4 pages)

PAGE 1
LPKMOD CONVERSION KITS MODULATING FURNACE NATURAL GAS TO L.P. GAS CONVERSION DESCRIPTION CONTENTS OF KIT This natural gas to L.P. (liquid petroleum) gas conversion kit allows modulating furnaces to be used on L.P. gas applications. The following table lists the kit number and the applicable models. The appropriate kit must be matched to the appropriate model number for safe and reliable operation. Upon opening the kit, please verify that all parts are in an undamaged condition.
PAGE 2
NOTE: Do not use power tools for any adjustments on gas valves. The following tools and supplies are required: • 2 – Pipe wrenches, properly sized to accommodate the gas piping and connectors • 1 - 5/16" nut driver • 1 – 1/4" nut driver • 1 – manometer to read inlet and outlet pressure of the gas valve (Minimum range: 0”-20” W.C.) • Pipe joint compound or pipe thread tape • Gas leak detection solution like a soap and water solution.
PAGE 3
5. Always use a backup wrench when removing or replacing piping to avoid any undue strains or rotation of controls. 6. Remove the wires from the gas valve. Be sure to remove any wire ties that may be attached to the manifold assembly. 7. Remove the pressure switch hose connected to the gas valve. 8. Remove the 4 sheet metal screws that fasten the manifold/gas valve assembly to the burner box. Retain the natural gas manifold/valve assembly for possible future reconversion to natural gas. 9.
PAGE 4
time during a heating cycle, at which time the display will show “Ft”. While the display is showing “Ft”, pressing and holding the Fault Recall Push-Button for 3 seconds will enable the field test mode and override the normal firing rate sequence at a rate of 100% for 5 minutes or until the end of the call for heat. The display will show the normal “Hi” while the control is firing at 100%.