GMES80 Installation Manual

22
1 2 3 1 2 3
Position
OFF OFF OFF ON OFF OFF
Motor Speed
COOL
Y T1 T2
1 2 3 1 2 3 *1 2 3
ON ON OFF OFF ON OFF OFF OFF ON
Motor Speed
COOL
T3 T4 T1+T2
1 2 3 1 2 3 1 2 3
OFF ON ON ON OFF ON ON ON ON
Motor Speed
COOL
T1 T1 T1
COOL MOTOR SPEED DIP SWITCH SETTING (S1-1, S1-2, S1-3)
* = DEFAULT SETTING
1 2 *1 2 1 2 1 2
Position OFF OFF ON OFF ON ON OFF ON
Motor
Speed
HEAT
W T1 T2 T3 T4
HEAT MOTOR SPEED DIP SWITCH SETTING (S2-1, S2-2)
* = DEFAULT SETTING
*3 4 3 4 3 4 3 4
Position OFF OFF ON OFF OFF ON ON ON
Motor
Speed
FAN
G T1 T2 T4 T1+T2
FAN MOTOR SPEED DIP SWITCH SETTING (S2-3, S2-4)
* = DEFAULT SETTING

WARNING
T
O AOI PERSONAL INJURY OR EATH, O NOT REMOE ANY INTERNAL
COMPARTMENT COERS OR ATTEMPT ANY AJUSTMENT.
E
LECTRICAL
COMPONENTS ARE CONTAINE IN BOTH COMPARTMENTS.
C
ONTACT A
UALIFIE SERICE AGENT AT ONCE IF AN ABNORMAL FLAME APPEARANCE
SHOUL EELOP.

Refer to your furnace rating plate for the maximum ESP (ex-
ternal duct static) rating.
Total external static refers to everything external to the furnace
cabinet. Cooling coils, lters, ducts, grilles, registers must all
be considered when reading your total external static pres-
sure. The supply duct pressure must be read between the
furnace and the cooling coil. This reading is usually taken by
removing the “A” shaped block o󰀨 plate from the end on the
coil; drilling a test hole in it and reinstalling the block o󰀨 plate.
Take a duct static reading at the test hole. Tape up the test
hole after your test is complete. The negative pressure must
be read between the lter and the furnace blower.

T O AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK ,
TURN OFF POWER TO THE FURNACE BEFORE CHANGING SPEED TAPS .
WARNING
Furnaces are equipped with a EEM circulator blower motor.
This provides ease in adjusting blower speeds. Refer to the
Blower Performance Data in the back of the manual for proper
selection of heating and cooling speeds.
To adjust the circulator blower speed, proceed as follows:
1. Motor speed Tap wiring must remain in factory position
on the control board and motor
2. There are 4 speed Tap wires to the motor T1, T2, T3,
T4.)
3. There are 5 speeds available, depending on DIP switch
settings mentioned in air ow tables for each size
furnace.
4. Cooling speed can be adjusted by adjusting S1-1, S1-2,
S1-3 (see cooling airow Chart for reference).
5. Heating speed can be adjusted by adjusting S2-1, S2-2
(see Heating airow Chart).
6. Circulation / Continuous Fan speed can be adjusted by
adjusting S2-3, S2-4 (see Circulation airow Chart).
7. Verify Proper temperature rise as outlined in the
Temperature Rise section of Startup Procedure and
Adjustment. Please refer to the tables below for dip
switch settings.
CONNECTOR ID DESCRIPTION CONNECTOR VOLTAGE
L LINE, L1 LINE, L1
G GROUND CHASSIS GROUND
N LINE, L2 LINE, L2
C SIGNAL COMMON 24VAC COMMON
1 TAP 1 24VAC
2 TAP 2 24VAC
3 TAP 3 24VAC
4 TAP 4 24VAC
5 TAP 5 24VAC
Motor Tap Identification
S1-4 Min Nom Max Units
ON
*150
Seconds
OFF 100 Seconds
Heat Off Delay (S1-4)
* = DEFAULT SETTING