Z-Wave Window/Door Detector User’s Manual TD1110Z1
ABOUT THIS MANUAL This manual is designed for use with the Z-Wave Window / Door Detector. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice.
a. for FCC 15b devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents 1. Introduction ............................................................................................................1 Features ............................................................................................................................. 2 Package Contents .............................................................................................................. 3 LED Indicator .......................................................................................
1. Introduction This detector enables you to detect when your window/door is opened or closed. This detector allows you to assign lights or appliances to turn on and off when the attached window/door is being opened or closed. You can monitor any window/door status in your home through PC connectivity using a Z-wave USB dongle when you are away from home.
Features Simple plug and play installation. Support device linking for triggering multiple devices to provide maximum security. Fully compatible with Z-wave enabled network, capable of communicating with any Z-wave certified device Package Contents Z-Wave Window / Door Detector x1 1.5 V AAA battery x2 User’s Manual x1 LED Indicator Color Red Description Light : When the window or door is open.
Wireless Range The Z-Wave Lamp Dimmer Switch is made wireless by Z-Wave technology. Typical range for a wireless module is approximately 100 feet. When installing the module consider an open area with little obstruction for the best signal and performance. Avoiding the obstruction between the module and controller may make a negative effect on wireless performance and range.
2.
Product Description Below is a description of button, light and plugs for the Z-Wave Window / Door Detector. LED The light will blink to indicate that the module has been entered “Program Mode” or when it is communicating wirelessly to the Z-Wave controller, such as Z-Wave Dongle. Contact Magnet The magnet is used to detect if the window or door are open. Magnetic contact is placed next to the Window / Door Detector.
Cable Conduit This product provides extending switch function for user’s use. Please purchase a normal on/off switch first and in order to maximize the utility and use of this product, please take the following steps to install this additional function. 1. Please open the battery lid by prepared screwdriver. User can see two hole beside this product clearly. 2. Now connect prepared normal switch to this two hole by screwdriver as instruction.
3. Make sure the operation and status of LED indicator are working, please put the battery lid back and ready to use.
Installation Requirements To install this product you must have Z-Wave enabled controller, such as Z-Wave Dongle, to make an association with Z-Wave Window / Door Detector. Installing the Z-Wave Window / Door Detector NOTE ======================================================= Before you install or use this Z-Wave Window / Door Detector, please install your Z-Wave controller first and make an inclusion for your Z-Wave device. Not all Z-Wave enabled remote controls have the same installation process.
To mount your Z-Wave device The Z-Wave Window/Door Detector can be mounted on any location that can be open or closed, such as closets, doors, windows, safes. The Z-Wave Window/Door Detector can be mounted in two ways: Double Sided Tapor Screws. These instructions will go over the screw mounting method. 1. Unscrew the Battery Lid from the Door/ Window Sensor and slide the lid off. 2. Use the screws that provided in the mounting kit to screw the lid onto your desired location. 3.
3. Specifications Item Description Protocol Z-Wave Sensor Type Magnet Power Mode Self Power Power Battery 1.5V AAA size * 2 Low battery indicator : Battery indicator shows when the LED Indicator battery voltage falls below at normal position (Dual color) Red color : Door/Window open status Green color : Low battery status. Frequency 908.42MHZ( US)/ 868.
4. Regulatory Compliance FCC Conditions This device complies with Part 15 of the FCC Rules.
