T500EN rev.0205 Audio and Video door entry system digital installation Stadio Plus golmar@golmar.es www.golmar.es Golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifications without prior notice.
1 INTRODUCTION First of all we would like to thank and congratulate you for the purchase of this product manufactured by Golmar. The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification and for the manufacturing of products like this one. Its advanced technology and exacting quality control will do that customers and users enjoy with the legion of features this system offers.
DOOR PANEL DESCRIPTION D oor panel description. 4 DOOR PANEL INSTALLATION E mbedding box positioning. 600 closing heads CE-6xx embedding boxes 1xxx 2xxx grille module 1850 1450 1650 3xxx push buttons module The upper part of the door panel should be placed at 1,65m. height roughly. The hole dimensions will depend on the number of door panel modules. Sound module EL530 , on video systems with b/w camera. EL531 , on video systems with color camera. EL540 , on audio systems.
5 DOOR PANEL INSTALLATION 6 DOOR PANEL INSTALLATION P A lace the embedding box. ssembly the sound module. Pass the wiring through the hole made in the bottom part of the embedding box. Level and flush the embedding box. Once the embedding box is placed, remove the protective labels from the attaching door panel holes. Insert the sound module in the grille module.
DOOR PANEL INSTALLATION H 7 8 DOOR PANEL INSTALLATION C old the door panel on the embedding box. ableado de los pulsadores. Select a direction to open the door panel; this selection should ease the door panel wiring. The opening direction will be settled through the hinges position, that must be passed through the header clips as shown.
9 DOOR PANEL INSTALLATION 10 DOOR PANEL INSTALLATION P P ush buttons wiring. The CN2 connector of the EL500 microprocessed circuit has 8 terminals (P1 to P8) for the connection of push buttons or EL516 encoders. The CP terminal of the EL500 circuit must be connected to the push buttons common terminal and to the CP terminal of the push buttons encoders. Connect B terminal to the B terminal of the encoders. To the 1st push b. or to the P terminal of the 1st EL516. To the next push b.
11 DOOR PANEL INSTALLATION D escription of the configuration jumpers. The JP1, JP2, JP3 and JP4 configuration jumpers (from left to right respectively) are placed on the left side of the EL500 circuit, and are accessible by opening the terminal connector protection cover. Jumper JP1 loads the installation with a communications resistor. For a proper system operation, activate this resistor only in the closest door panel to the backbone installation or in the general entrance door panel (if exists).
DOOR PANEL INSTALLATION L amps wiring. 13 14 I POWER SUPPLY INSTALLATION nstalling the FA-PLUS and FA-PLUS/C power supplies. Once the nameplate labels are placed, wire the lamps from different modules and connect them to terminals L1 and L2 of the sound module. If the number of door panel lamps is higher than eight, connect a TF-104 transformer between ~1 and ~2 terminals of the sound module and change JP2 jumper position. f 3,5 x 25 DIN-7971 NOTE: Don't change JP1 jumper position.
15 MONITOR DESCRIPTION f g b Monitor Modelo Nº serie 18Vdc ± 2V Standby 15mA Máximo 450mA 10ºC + 50ºC 0000000000 PLATEA Plus ATENCIÓN Alta tensión. No abrir la tapa. Manipular sólo por personal del servicio técnico. WARNING High voltage. Don't open cover. Handle only by technical service. MASTER SLAVE INTER A1 CODIGO / CODE ESCALERA Stair PISO Floor PUERTA Door MONITOR DESCRIPTION F unction push buttons. On-Off push button.
17 MONITOR ADJUSTMENTS 18 MONITOR CONNECTOR DESCRIPTION E D L562 module for video installations with twisted pair Locate the CN4 connector, that's placed in the monitor base. Remove the existing jumper and plug the EL562 module. NOTE: on this type of installations the EL560 module must be plugged in the EL500 microprocessed circuit (page 12). Refer to the specific installation diagram. escription of the RCPL-Plus monitor connector. a c b d H andling the end of line jumper. 50mm. 50mm.
MONITOR INSTALLATION 19 F 20 MONITORS PROGRAMMING P ix the monitor connector to the wall. rogramming the monitors. Avoid to place the monitor near to heating sources, in dusty locations or smoky environments. To install the monitor directly over the wall, drill two holes of Ø6mm. and use the supplied screws. The upper part of the monitor connector must be placed at 1,60m. height roughly. The minimum distance between the monitor connector and the closest object must be 5cm.
21 TELEPHONE DESCRIPTION D b d a c e escription of the T-940 Plus telephone. 22 TELEPHONE DESCRIPTION T erminal connector description. a. Telephone handset. b. Speaker grille. c. Microphone hole. d. Subjection hole. e. Telephone cord connectors. f. Function push buttons. g. On-Off light indicator. h. Call reception volume control. i. Hook switch. + _ A D INT SA HZ- + , – : positive, ground. A , D : audio, digital communication. INT : intercom. SA : auxiliary calling device output.
TELEPHONES PROGRAMMING 23 P 24 INSTALLATION DIAGRAMS C onnexion of an a.c. lock release. rogramming the telephones. As it is described on page 14, the lock releases to be connected to the door panel must be d.c. type. If an a.c. lock release has been installed before, use a R-3 relay unit and a TF-104 transformer, and connect them to the lock release as it is shown on the enclosed diagram.
25 * Take off JP1 jumper of all the distributors except in the last one. 26 INSTALLATION DIAGRAMS D4L-PLUS CN4 JP1 S + _ Vin Malla Vout A D D1 E v CN4 D2 + _ Vin Malla Vout A D The installation diagram shows the connection of a video system with one or several door panels for the same building. If the system has one door panel only, override the wiring to the second door panel. If the system has more than one door panel, wire the second panel as shown on the diagram.
EL562 JP1 27 EL562 JP1 * Take off JP1 jumper of all the distributors except in the last one. + _ A D Vp Mp Md1 Vd1 + _ A D Vpo Mpo + _ A D CT + _ A D Vpi Mpi INSTALLATION DIAGRAMS + _ A D Vp Mp v D6L-Plus/2H Md6 Vd6 ideo installation without coaxial cable. The installation diagram shows the connection of a video system with one or several door panels for the same building. If the system has one door panel only, override the wiring to the second door panel.
29 T-940 Plus 30 INSTALLATION DIAGRAMS T-940 Plus + _ A D A + _ A D udio installation. The installation diagram shows the connection of an audio system with one or several door panels for the same building. If the system has one door panel only, override the wiring to the second door panel. If the system has more than one door panel, wire the second panel as shown on the diagram. In case of more than two door panels, wire them as the second is connected.
31 OPTIONAL CONNECTIONS E 32 OPTIONAL CONNECTIONS I xternal lock release activation. ntercom function. CV- CV+ - The lock release can be activated at any moment by using an external push button, that must be connected between 'CV–' y '–' terminals of the EL500 circuit. This function will allows to exit from the building being not necessary the use of a key. Platea Plus monitor and T-940 Plus telephone have intercom facility between two units of the same apartment.
33 OPTIONAL CONNECTIONS A ctivation of a second camera. The use of a SAR-90 relay will be required to activate a second camera and an internal modification on the monitor shall be done, as it's described on page 16. This facility disables the intercom function. If both functions are required, use A1 terminal to activate the second camera. To activate this function, press monitor push button at any moment with no dependence of the handset position.
